The class device only handles descriptor information specific to the class,
and shared descriptor information is passed through parameters and
handled by the composite driver.
Signed-off-by: zhangyuan21 <zhangyuan21@xiaomi.com>
The original code hard-coded card detection to the low when card is
inserted and high when not. This might not be true on every board
because it depends on the slot and wiring used. The second reason is
because it is also possible to detect card with D3 pin pull-up when the
slot does not provide dedicated card detection switch.
This introduces new argument to the sam_hsmci_initialize to allow
invert of card detection pin. It also applies this invert to existing
boards as that was the state up to this point.
In order to support multiple LCD instances per board, add a pointer from
lcd_planeinfo_s to the lcd_dev_s which it belongs to. Also enhance the
putrun, getrun, putarea and getarea methods to pass through the
lcd_dev_s pointer to the respective device driver.
Port all LCD device drivers to this lcd_planeinfo_s extension.
Enhance SSD1306 driver to support multiple LCDs.
Signed-off-by: Michael Jung <michael.jung@secore.ly>
This introduce common folder structre and rework scripts & tools
files. The linker scripts were reorganized to use best the current
infrastructure which uses a template to create a final samv7.ld
file based in the current SoC memories and bootloader definitions.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
After define memory sizes for samv7 it is possible unify linker scripts.
This add necessary changes to perform such operation.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Gregory Nutt is the copyright holder for those files and he has submitted the
SGA as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
SPI0 is used for the connection of the LCD controller.
Additional SPI and GPIO signals definitions:
SPI0_NPCS1 - SPI Chip Select, PD25
GPIO_LCD_CD - Command/Data, pin PB2
GPIO_LCD_RST - Reset, pin PB3
boards/arm/samv7/samv71-xult/src/sam_st7789.c is
derived from boards/arm/imxrt/teensy-4.x/src/imxrt_st7789.c
Signed-off-by: Jaroslav Beran <jara.beran@gmail.com>
sam_ili9488.c:1605:7: error: label 'errout_with_dmadog' used but not defined
bcmf_sdio.c:855:16: error: passing argument 1 of 'wd_start' from incompatible pointer type
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
to save the preserved space(1KB) and also avoid the heap overhead
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: I694073f68e1bd63960cedeea1ddec441437be025
so the lower half driver don't need include the specific board.h
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: Icf6638a6865bac42150b5957376e55909f041d40
so the lower half driver don't need include the specific board.h
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: I2ff5c30049a5c5e8ee90baea56e9f4cb1a8a4f87
Summary
The naming standard at https://cwiki.apache.org/confluence/display/NUTTX/Naming+FAQ requires that all MCU-private files begin with the name of the architecture, not up_.
This PR addresses only these name changes for the up_*.h files. There are only three, but almost 1680 files that include them:
up_arch.h
up_internal.h
up_vfork.h
The only change to the files is from including up_arch.h to arm_arch.h (for example).
The entire job required to be compatible with that Naming Convention will also require changing the naming of the up_() functions that are used only within arch/arm and board/arm.
Impact
There should be not impact of this change (other that one step toward more consistent naming).
Testing
stm32f4discovery:netnsh
