sergiotarxz/nuttx
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
28,883 Commits 1 Branch 0 Tags 291 MiB
95cbbf552b
Commit Graph

1629 Commits

Author SHA1 Message Date
Konstantin Berezenko
95cbbf552b Change STM32 tickless to use only one timer 2017-03-30 10:40:05 -07:00
Juha Niskanen
5577f58458 STM32 RNG: Fix semaphore initial value and disable priority inheritance 2017-03-29 07:12:19 -06:00
Gregory Nutt
92da8068ed Merge branch 'master' of bitbucket.org:nuttx/nuttx 2017-03-26 06:57:35 -06:00
raiden00pl
f3367233b6 stm32_comp.c: typo 2017-03-26 09:36:53 +02:00
raiden00pl
c1090164f5 stm32/Kconfig: update COMP and OPAMP definitions 2017-03-26 09:34:17 +02:00
raiden00pl
6594c65a77 stm32_comp.c: cosmetic 2017-03-26 09:30:23 +02:00
Gregory Nutt
7d57a2b2bd Trivial changes from review of last PR. 2017-03-25 10:38:41 -06:00
raiden00pl
a806aedb13 STM32F33: Support for COMP character driver 2017-03-25 16:57:43 +01:00
Alexander Oryshchenko
61ff3c6b84 I needed to use DS3231, I remember that in past it worked ok, but now for stm32f4xx is used another driver (chip specific, stm32f40xxx_i2c.c) and DS3231 driver doesn't work. After investigating a problem I found that I2C driver (isr routine) has a few places there it sends stop bit even if not all messages are managed. So, e.g., removing stm32_i2c_sendstop (#1744) and adding stm32_i2c_sendstart after data reading helps to make DS3231 working. Verified by David Sidrane. 2017-03-24 06:44:33 -06:00
Aleksandr Vyhovanec
82a84a8d98 Merged nuttx/nuttx into master 2017-03-24 11:40:09 +03:00
no1wudi
4c6680df99 Merged in no1wudi/nuttx (pull request #291) 
fix compile error when disabled the flash data cache corruption for stm32 f1xx

Approved-by: Gregory Nutt <gnutt@nuttx.org>
 2017-03-24 00:58:26 +00:00
no1wudi
fd76a3db05 fix spacing 2017-03-24 08:52:46 +08:00
no1wudi
5797e84893 Merged nuttx/nuttx into master 2017-03-24 08:40:40 +08:00
David Sidrane
66910577be stm322_flash:missing unlock on F1 HSI off path 2017-03-23 14:22:45 -10:00
David Sidrane
7e3bec635b stm32_i2c_alt:Move def of regval to top func def per CS 2017-03-23 11:50:37 -10:00
David Sidrane
d25f8710d2 stm32f40xxx_i2c:Duplicate non CS dev of regval 2017-03-23 11:37:12 -10:00
David Sidrane
f5cf22d871 stm32_i2c_alt:Duplicate non CS dev of regval 2017-03-23 11:36:44 -10:00
David Sidrane
c2a1b719be stm32_flash:Need conditinal on non F4 targets 2017-03-23 11:33:32 -10:00
rg
9353ca6039 STM32 I2C: Do not allow CONFIG_I2C_POLLED and CONFIG_I2C_DMA 2017-03-23 11:24:18 -06:00
Aleksandr Vyhovanec
06af125e45 The interrupt occurs over the counter overflow 2017-03-23 17:34:45 +03:00
no1wudi
45f5d30e2e fix compile error when disabled the flash data cache corruption for stm32 f1xx 2017-03-23 13:38:26 +08:00
Gregory Nutt
3fb0a00c35 Small changes from review of last PR. Plus spacing and typo fix. 2017-03-22 17:32:52 -06:00
Gregory Nutt
947acd6c1a Small changes from review of last PR 2017-03-22 15:53:12 -06:00
José Roberto de Souza
b9b4f184a7 stm32: Add workaround for flash data cache corruption on read-while-write 
This is a know hardware issue on some STM32 see the errata of your model
and if you make use of both memory banks you should enable it.
 2017-03-22 13:14:19 -07:00
José Roberto de Souza
09f70c462d stm32: Make up_progmem thread safe 
Writing to a flash sector while starting the erase of other sector
have a undefined behavior so lets add a semaphore and syncronize
access to Flash registers.

But for the semaphore to work it needs to be initialized so each
board needs call stm32_flash_initialize() on initialization, so
to avoid runtime problems it is only using semaphore and making
it thread safe if initialized, after all boards starts to call
stm32_flash_initialize() we can remove the boolean and the check.
 2017-03-22 13:14:15 -07:00
José Roberto de Souza
80f56e75f9 stm32: Fix erase sector number for microcontrolers with more than 11 sectors 
Erase a sector from the second bank cause the bit 4 of SNB being set
but never unsed, so trying to erase a sector from the first bank
was acually eraseing a sector from the second bank.
 2017-03-22 12:42:20 -07:00
rg
82a5dfddb4 The attached .patch implements DMA support for the stm32f4 I2C. Max and I have verified that it works on our systems. 2017-03-21 16:44:11 -06:00
no1wudi
7d6ee0f222 fix a typo 2017-03-20 09:50:27 +08:00
Gregory Nutt
e8a30890f2 Cosmetic changes from review of last PR. 2017-03-19 13:05:31 -06:00
raiden00pl
651b8360c6 STM32F33: Add COMP support 2017-03-19 18:36:44 +01:00
raiden00pl
c760d00158 stm32f33xx_comp.h: fix typos 2017-03-19 18:27:31 +01:00
raiden00pl
fd42900dcc STM32F33: Add ADC support 2017-03-18 16:34:24 +01:00
raiden00pl
49e4e62aab STM32F33: Move DMA logic to a separate files 2017-03-18 16:31:06 +01:00
David Cabecinhas
08e92abb0b ARM: Remove redundant interrupt stack coloring 2017-03-16 19:13:39 +08:00
David Cabecinhas
86400a252d ARM: Fix off-by-one interrupt stack allocation in 8-byte aligned architectures 2017-03-14 20:01:45 +08:00
Gregory Nutt
4d33f26717 Update some comments 2017-03-12 12:33:44 -06:00
Gregory Nutt
d9cdb6c383 STM32; OTG host implementations of stm32_in_transfer() must obey the polling interval for the case of isochronous and itnerrupt endpoints. 2017-03-12 08:39:30 -06:00
Gregory Nutt
98a98a0c8b Minor change for consistency with a previous commit. 2017-03-12 07:20:10 -06:00
Gregory Nutt
9b11187b2a STM32 OTG HS: A little research reveals that only the F2 RCC initialization set the OTGHSULPIEN bit and Photon is the only F2 board configuration that uses OTG . Therefore, we can simplify the conditional logic of the last PR. Negative logic was used (#ifndef BOARD_DISABLE_USBOTG_HSULPI) to prevent bad settings in other configurations. But give these facts, the preferred positive logic now makes more sense (#ifdef BOARD_ENABLE_USBOTG_HSULPI). 2017-03-11 18:00:38 -06:00
Gregory Nutt
e0f7b9582a STM32: Review of last STM32 F2 PR. Progate changes to STM32 F4 and F7 OTGHS. Rename some configs/photon/src files. Naming can be either photon_ or stm32_ but must be consistent. 2017-03-11 16:31:11 -06:00
Simon Piriou
70d8f0189d stm32f20xxx: add BOARD_DISABLE_USBOTG_HSULPI flag 2017-03-11 18:15:18 +01:00
Gregory Nutt
aadf6c6e16 STM32 F33: Fix another error in ADC base address usage. 2017-03-10 17:49:32 -06:00
Gregory Nutt
852b189910 STM32 F33 ADC: Correct bad definitions of base addresses; Fix naming collision by changing colliding STM32_ADC12_BASE to STM32_ADC12_CMN_BASE 2017-03-10 17:46:19 -06:00
Gregory Nutt
24816cb08b All STM32 host drivers. In IN endpoint retry, delay for a clock tick to give some breathing space for the CPU. EXPERIMENTAL change. 2017-03-10 10:25:43 -06:00
David Sidrane
acaebb361b STM32, STM32 F7, and STM32 L4: Clone Freddie Chopin's I2C change to similar STM32 I2C drivers. 
Save elapsed time before handling I2C in stm32_i2c_sem_waitstop()
   This patch follows the same logic as in previous fix to
   stm32_i2c_sem_waitdone().
   It is possible that a context switch occurs after I2C registers are read
   but before elapsed time is saved in stm32_i2c_sem_waitstop(). It is then
   possible that the registers were read only once with "elapsed time"
   equal 0. When scheduler resumes this thread it is quite possible that
   now "elapsed time" will be well above timeout threshold. In that case
   the function returns and reports a timeout, even though the registers
   were not read "recently".
   Fix this by inverting the order of operations in the loop - save elapsed
   time before reading registers. This way a context switch anywhere in the
   loop will not cause an erroneous "timeout" error.
 2017-03-10 05:07:39 -10:00
Freddie Chopin
3cd66af889 ave elapsed time before handling I2C in stm32_i2c_sem_waitstop() 
This patch follows the same logic as in previous fix to
stm32_i2c_sem_waitdone().

It is possible that a context switch occurs after I2C registers are read
but before elapsed time is saved in stm32_i2c_sem_waitstop(). It is then
possible that the registers were read only once with "elapsed time"
equal 0. When scheduler resumes this thread it is quite possible that
now "elapsed time" will be well above timeout threshold. In that case
the function returns and reports a timeout, even though the registers
were not read "recently".

Fix this by inverting the order of operations in the loop - save elapsed
time before reading registers. This way a context switch anywhere in the
loop will not cause an erroneous "timeout" error.
 2017-03-10 07:35:10 -06:00
Gregory Nutt
9cd3f7f80a STM32, STM32 F7, STM32 L4: OTG host drivers: Do not do data toggle if interrupt transfer is NAKed. Sugested by webbbn@gmail.com 2017-03-09 15:07:31 -06:00
Simon Piriou
6768831851 Merged in spiriou/nuttx (pull request #257) 
STM32F2: add USB OTG HS support for stm32f20xxx cores

Approved-by: Gregory Nutt
 2017-03-09 20:06:12 +00:00
Gregory Nutt
04297d1b0f Update some comments 2017-03-09 13:57:37 -06:00
Gregory Nutt
a3b4475474 STM32, STM32 F7, and STM32 L4: Back out part of 3331e9c49a. Returning immediately int he case of a NAK makes the Mass Storage Class driver unreliable. The retry/timeout logic is necessary. This implementation tries to implement a compromise: If a NAK is received after some data is received, then the partial data received is returned as with 3331e9c49a. If if a NAK is received with no data, then no longer returns the NAK error immediately but retries until data is received or a timeout occurs. Initial testing indicates that this fixes the issues the MSC. However, I hae concerns that if multiple sectors are read in one transfer, there could be NAKs between sectors as well and, in that case, then change will still cause failures. 2017-03-09 13:49:25 -06:00