It uses the memory block as the serial communication medium, which can communicate between different processes or different CPUs
Using the following configuration, the cross-core communication rate of 200MHz cortex-M55 is about 461KB/s
RAM_UART_BUFSIZE=1024
RAM_UART_POLLING_INTERVAL=100
Signed-off-by: yinshengkai <yinshengkai@xiaomi.com>
1. virtio devics/drivers match and probe/remote mechanism;
2. virtio mmio transport layer based on OpenAmp (Compatible with both
virtio mmio version 1 and 2);
3. virtio-serial driver based on new virtio framework;
4. virtio-rng driver based on new virtio framework;
5. virtio-net driver based on new virtio framework
(IOB Offload implementation);
6. virtio-blk driver based on new virtio framework;
7. Remove the old virtio mmio framework, the old framework only
support mmio transport layer, and the new framwork support
more transport layer and this commit has implemented all the
old virtio drivers;
8. Refresh the the qemu-arm64 and qemu-riscv virtio related
configs, and update its README.txt;
New virtio-net driver has better performance
Compared with previous virtio-mmio-net:
| | master/-c | master/-s | this/-c | this/-s |
| :--------------------: | :-------: | :-------: | :-----: | :-----: |
| qemu-armv8a:netnsh | 539Mbps | 524Mbps | 906Mbps | 715Mbps |
| qemu-armv8a:netnsh_smp | 401Mbps | 437Mbps | 583Mbps | 505Mbps |
| rv-virt:netnsh | 487Mbps | 512Mbps | 760Mbps | 634Mbps |
| rv-virt:netnsh_smp | 387Mbps | 455Mbps | 447Mbps | 502Mbps |
| rv-virt:netnsh64 | 602Mbps | 595Mbps | 881Mbps | 769Mbps |
| rv-virt:netnsh64_smp | 414Mbps | 515Mbps | 491Mbps | 525Mbps |
| rv-virt:knetnsh64 | 515Mbps | 457Mbps | 606Mbps | 540Mbps |
| rv-virt:knetnsh64_smp | 308Mbps | 389Mbps | 415Mbps | 474Mbps |
Note: Both CONFIG_IOB_NBUFFERS=64, using iperf command, all in Mbits/sec
Tested in QEMU 7.2.2
Signed-off-by: wangbowen6 <wangbowen6@xiaomi.com>
Signed-off-by: Zhe Weng <wengzhe@xiaomi.com>
usage:
1. Connect Jlink, start JLinkGDBServer
JLinkGDBServer -if SWD -device stm32h743zi -speed 16000
2. Listen to the RTT port data and forward it to the virtual serial port
sudo socat -d -d PTY,link=/dev/ttyRTT0,raw,ignoreeof TCP:127.0.0.1:19021,reuseaddr
3. Read serial data
minicom -D /dev/ttyRTT0
Performance:(STM32H743, 400MHZ)
time "dd if=/dev/zero of=/dev/console bs=512 count=2048"
6.67 sec 157KB/s
Signed-off-by: yinshengkai <yinshengkai@xiaomi.com>
Like rpmsgdev and rpmsgmtd, rpmsgblk allow the local cpu to
access the block device in the remote cpu.
Signed-off-by: wangbowen6 <wangbowen6@xiaomi.com>
