Linux kernel uses M-mode trap for handling Inter-Hart Communication (IHC).
This patch provides all the required functionalities for this purpose.
Previously, HSS bootloader was required. Now, NuttX is run as the
bootloader providing OpenSBI vendor extensions instead. This setup has
been tested on the following configuration:
- Hart 0 has NuttX in bootloader mode with OpenSBI
- Hart 1 unused
- Hart 2 has NuttX configured at 0xa2000000
- Hart 3 has U-boot / Linux kernel (at 0x80200000)
- Hart 4 has U-boot / Linux kernel (at 0x80200000)
Upon startup, NuttX on hart 0 will initialize SD-card driver, loads
the hart 2 NuttX from the SD-card and loads the U-boot to 0x80200000.
Also the nuttx.sbi -binary is loaded from SD-card into address 0x80000000,
which is also marked as reserved area in the Linux kernel device tree (for
the chuck 0x80000000 - 0x80200000).
Hart 2 NuttX waits until Linux kernel (IHC master) is started. After the
initial handshake, RPMsg / virtIO bus along with the IHC may be used for
proper AMP mode.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
1. Add vbat mode for chip internal voltage sample;
2. Add adc channel config;
3. Using DFIFO2 to get the sample value, follow telink sdk.
4. Add calibration function and config;
Signed-off-by: wangbowen6 <wangbowen6@xiaomi.com>
This provides an example of Asymmetric Multiprocessing (AMP). The
master from Linux sends pings that this NuttX echoes back. The system
uses RPMsg from OpenAMP.
The Inter-Hart Communication module is present in the vendor's software
stack with the tag "2021.11". The software is present on github at the
polarfire-soc project. The following conditions must be met:
1. FPGA programmed with 2021.11 software
2. HSS (Vendor bootloader) with 2021.11 software
3. U-boot and Linux kernel from 2011.11 software
Currently the IHC works as a slave only on the hart number 4.
On the NuttX side, this patch uses rptun that incorporates rpmsg and
virtio. If it used only rpmsg and virtio, the future maintenance would
likely be much heavier. Using rptun also simplifies many things.
Upon success, the master side from Linux may issue an example test:
root@icicle-kit-es-amp:/opt/microchip/amp/rpmsg-pingpong# ./rpmsg-pingpong
However, the rpmsg-pingpong.c (compiled on target with gcc), may need to
be modified as seen below to match the device id:
- char *rpmsg_dev="virtio0.rpmsg-amp-demo-channel.-1.0";
+ char *rpmsg_dev="virtio0.rpmsg-amp-demo-channel.-1.1024";
This work uses a separate linker script. Due to a bug yet unknown to date,
a small NuttX, when loaded by the vendor HSS bootloader, will cause the
Linux kernel to hang at boot. Thus, the binary size is increased with
a section 'filler_area' whose only purpose is to increase the image size
so that the Linux kernel will boot up.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
1. add pulse count support for pwm0;
2. add more detailed config for pwm;
3. pwm configuration and start process optimize;
4. tlsr82/Kconfig format;
Signed-off-by: wangbowen6 <wangbowen6@xiaomi.com>
Summary:
- The configuration is no longer needed because Kconfig has
been fixed in the previous commit
Impact:
- None
Testing:
- Tested with QEMU
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
to generate more information for profile feedback optimization
and remove -lgcov from STDLIBS since gcc/clang will automatically
add the profile help lirary(triggered by -fprofile-generate).
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Summary:
- This commit adds hostfs support to nsh and nsh64 defconfigs
Impact:
- None
Testing:
- Tested with qemu-6.2
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Mappings are done with vaddr=paddr.
- I/O space mapped with two gigapages
- Kernel space mapped to statically allocated page tables. 2MB of kernel
memory is supported.
- Page pool is mapped to the kernel space, to allow virtual memory access
for the kernel e.g. to initialize the page memory when it is allocated.
Summary:
- I noticed that cxxtest does not work correctly.
- Finally, I found that initializers for c++ is not called.
- This commit fixes this issue
Impact:
- None
Testing:
- Tested with cxxtest (defconfig will be added later)
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- Correct boardctl function's return value
- In case of BOARDIOC_TESTSET, `ret' has 0 or 1 or an error,
but `ret' is ignored except error.
Impact:
- boardctl return value except errors
Testing:
- custom Cortex-A9 board
Signed-off-by: Oki Minabe <minabe.oki@gmail.com>
Selecting this option will pass "-Map=$(TOPDIR)$(DELIM)nuttx.map" to ld
when linking NuttX ELF. That file can be useful for verifying
and debugging magic section games, and for seeing which
pieces of code get eliminated with DEBUG_OPT_UNUSED_SECTIONS.
Signed-off-by: chao.an <anchao@xiaomi.com>
Enable this option to optimization the unused input sections with the
linker by compiling with " -ffunction-sections -fdata-sections ", and
linking with " --gc-sections ".
Signed-off-by: chao.an <anchao@xiaomi.com>
Follow: http://glennastory.net/boot/sysinit.html
This is first script that init runs is rc.sysinit. This
script does serval initialization tasks about basic service.
The boot sequence currently provided to the board level is:
board_earlyinitialize->
board_lateinitialize(Peripherals driver, core driver, ...)->
run rcS script(mount fs, run service) ->
board_appinitialize->
After this patch:
The boot sequence currently provided to the board level is:
board_earlyinitialize->
board_lateinitialize(core driver,...)->
run rc.sysinit script(mount fs, run core service) ->
board_appinitialize(Peripherals driver)->
run rcS script(run other service)->
So, Peripheral drivers can do more with the file system and
core services.
Signed-off-by: Jiuzhu Dong <dongjiuzhu1@xiaomi.com>
since it is broken and inefficient, and then removed by:
commit dc961baaea
Author: chao.an <anchao@xiaomi.com>
Date: Thu Apr 14 18:07:14 2022 +0800
arm/armv7-[a|r]: move fpu save/restore to assembly handler
Save/Restore FPU registers in C environment is dangerous practive,
which cannot guarantee the compiler won't generate the assembly code
with float point registers, especially in interrupt handling
Signed-off-by: chao.an <anchao@xiaomi.com>
commit 8d66dbc068
Author: chao.an <anchao@xiaomi.com>
Date: Thu Apr 7 13:48:04 2022 +0800
arm/armv[7|8]-m: skip the fpu save/restore if stack frame is integer-only
Signed-off-by: chao.an <anchao@xiaomi.com>
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
It caused i2c tool not to work due to i2c uninitializing processing.
Since this process is not necessary in the normal case, we will
move it to the error case.
- Add config "ARCH_USE_S_MODE" which controls whether the kernel
runs in M-mode or S-mode
- Add more MSTATUS and most of the SSTATUS register definitions
- Add more MIP flags for interrupt delegation
- Add handling of interrupts from S-mode
- Add handling of FPU from S-mode
- Add new context handling functions that are not dependent on the trap
handlers / ecall
NOTE: S-mode requires a companion SW (SBI) which is not yet implemented,
thus S-mode is not usable as is, yet.
RISC-V GCC is configured with --enable-initfini-array so it emits an
.init_array section instead of .ctors
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
## Summary
`esp32c3_spi2_cmddata()` implements SPI Cmd/Data `SPI_CMDDATA()` for only 3 LCD drivers: ST7735, ST7789 and GC9A01.
This patch removes the check for LCD drivers, so that SPI Cmd/Data will work for all LCD drivers.
More details: https://github.com/apache/incubator-nuttx/pull/5898
## Impact
This change impacts LCD drivers that call `SPI_CMDDATA()`.
Previously `SPI_CMDDATA()` would fail with `ENODEV` for LCD drivers other than ST7735, ST7789 and GC9A01.
After patching, `SPI_CMDDATA()` will work correctly with all LCD drivers.
## Testing
This is a minor patch so no testing is needed.
Add MCUboot Update Agent and Slot Confirm configurations. It uses
ethernet with dhcp client to perform download of new image into
internal flash memory.
Signed-off-by: Gerson Fernando Budke <gerson.budke@ossystems.com.br>
MCUboot apps were moved to examples directory. This fix configs due to
recent changes.
Signed-off-by: Gerson Fernando Budke <gerson.budke@ossystems.com.br>
MCUboot apps were moved to examples directory. This fix configs due to
recent changes.
Signed-off-by: Gerson Fernando Budke <gerson.budke@ossystems.com.br>
MCUboot apps were moved to examples directory. This fix configs due to
recent changes.
Signed-off-by: Gerson Fernando Budke <gerson.budke@ossystems.com.br>
Move the target specific memory map to a separate file so there is no
need to copy&paste the __xxram_start etc linker symbols to each file
that needs them.
Also add MMU flags for I/O and kernel areas, they will be needed
when the kernel runs with virtual addresses also.
Summary:
- This commit enables environ and path in knsh/defconfig
Impact:
- None
Testing:
- Tested with QEMU
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
```
board/esp32_bringup.c: In function 'esp32_bringup':
board/esp32_bringup.c:171:9: error: implicit declaration of function 'esp32_efuse_initialize'; did you mean 'esp32_mmcsd_initialize'? [-Werror=implicit-function-declaration]
ret = esp32_efuse_initialize("/dev/efuse");
^~~~~~~~~~~~~~~~~~~~~~
esp32_mmcsd_initialize
```
Summary:
- I noticed that undefined instruction happens with getprime and gcc-10.3.1
- Actually, the issue does not happen with gcc-9.3.1
- This is a tentative solution to avoid the issue
Impact:
- sabre-6quad:knsh only
Testing:
- Tested with hello/getprime
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Mux USB IO pins one-by-one using package specific pinmux definitions. This avoids accidentally overwriting IO settings for other pins.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
This adds a simple USB device driver for the mpfs. However,
this driver is still at its early phase. Only limited testing
with CDC/ACM has been conducted.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
The imxrt1064, imxrt1064, and teensy-4.x board configs would fail to
build when CONFIG_USERLED_LOWER was enabled, due to a missing header in
imxrt_appinit.c and an unset local define.
Verified a build succeds for the specified boards with the following
defconfig modifications:
# CONFIG_ARCH_LEDS is not set
CONFIG_USERLED=y
CONFIG_USERLED_LOWER=y
Tested the "leds" Led driver example on a Teensy 4.1.
Gregory Nutt is the copyright holder for those files and he has submitted the
SGA as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Summary:
- I noticed that automatic tests sometimes fail
- This commit fixes this issue
Impact:
- None
Testing:
- Tested with QEMU
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- Add sabre-6quad:knsh to test BUILD_KERNEL with qemu
- Update README.txt to run the nuttx with qemu
Impact:
- None
Testing:
- Tested with QEMU
- NOTE: getprime crashes with undefined instruction when
compiled with gcc 10.3.x (please use 9.3.1)
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- This commit adds thumb support to i.MX6
- Also, applies the same coding style to arch_elf.c
Impact:
- i.MX6 only
Testing:
- Tested with sabre-6quad:smp (QEMU, Dev board)
- Tested with sabre-6quad:netnsh (QEMU)
- Tested with sabre-6quad:netknsh (QEMU, not merged yet)
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
The LSM303AGR and LSM6DSL depend on BSD license and should be disabled by default
They can be enabled after BSD components are selected in menuconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
NET_TUN depends on BSD components
Can be enabled after developer enables the BSD_LICENSE option in the menu
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
The BSD components should not be enabled by default.
Each developer can enable non Apache components locally
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Summary:
- I noticed two issues in the previous commit
- QEMU setting is missing
- The ostest takes longer time (i.e. 6m13s)
- This commit fixes these issues
Impact:
- None
Testing:
- Tested with QEMU
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
## Summary
A lot of linker scripts were listed twice, once for unix, once for windows.
This PR cleans up the logic so they're only listed once.
## Impact
Any opportunity to use a single source of truth and reduce lines of code is a win!
## Testing
CI will test all build
State of problem:
- Some drivers that do not support write operations (does not
have write handler or ioctl do not perform any write actions)
are registered with write permissions
- Some drivers that do not support read operation (does not
have read handler or ioctl do not perform any read actions)
are registered with read permissions
- Some drivers are registered with execute permissions
Solution:
- Iterate code where register_driver() is used and change 'mode'
parameter to reflect the actual read/write operations executed
by a driver
- Remove execute permissions from 'mode' parameter
Signed-off-by: Petro Karashchenko <petro.karashchenko@gmail.com>
Summary:
- Apply the same style as sabre-6quad
Impact:
- None
- NOTE: esp32c3-devkit still remains old style because of link errors
Testing:
- Build only
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- I noticed that the following error happened when loading the init
'elf_symvalue: SHN_COMMON: Re-compile with -fno-common'
- This commit fixes this issue
Impact:
- sabre-6quad only
Testings:
- Tested with sabre-6quad:netknsh (not merged yet)
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Support for the STMicroelectronics B-U585I-IOT02A development board. This
is a proof-of-concept port that demonstrates running NuttX as the
Non-Secure TrustZone domain companion to TrustedFirmware-M.
Signed-off-by: Michael Jung <mijung@gmx.net>
This commit adds board level support of PWM driver to SAME70-XPLAINED
board. The functionality is tested with two new configurations
pwm:
An example configuration with configured PWM.
pysim:
This configuration contains support for pysimCoder application and
includes ADC and PWM peripherals and Ethernet driver.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
board: nucleo-l152re: Added registering logic I2C on /dev.
squash 5 commits
board: nucleo-l152re: Add missing I2C1 GPIO definition
I2C1 not worked due to it's GPIO pin definition has been missing on board.h.
Fix it through include two pin macros on stm32l15xxx_pinmap.h(arch/arm/src/stm32/hardware) to board.h
GPIO_I2C1_SCL => PB8 (CN5 pin 10, D15)
GPIO_I2C1_SDA => PB9 (CN5 pin 9, D14)
Added board_late_initialize() function for init I2C.
board: nucleo-l152re: Added registering logic I2C on /dev.
I2C1 hasn't been registered on /dev. Fix it.
board: nucleo-l152re: Fix code style.
Update board.h
board: nucleo-l152re: Fix code style.
Variables starting with symbol '"g_*" means it is a global variable, I think this is not the case here.
Fix code style
since the related code was removed by:
commit 4d5a964f29
Author: Jiuzhu Dong <dongjiuzhu1@xiaomi.com>
Date: Tue Feb 23 18:04:13 2021 +0800
net: unify socket into file descriptor
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
We load the code into NuttX heap, which can be too far from
the usual code segments for the relocation types used by the
default "small" model to reach.
This worked around out of range relocations seen with my local app.
The image must be placed into:
boards/risc-v/mpfs/icicle/include/boot_romfsimg.h
The image is mounted by mpfs_bringup, which is run by the application
itself, or by board_late_initialize() in the case when
CONFIG_BOARD_LATE_INITIALIZE is defined, e.g. with CONFIG_BUILD_KERNEL
NOTE: THIS ONLY WORKS WHEN KERNEL RUNS IN M-MODE FOR NOW
This frees the PMP for other use, e.g. HART memory separation.
The page tables are statically allocated, 1 per level.
This feature is now behind CONFIG_MPFS_USE_MMU_AS_MPU, because
only the MPFS target supports this (others are not tested).
If the MMU is used for memory separation within a HART, the PMP must
still be configured to allow user access to the memory mapped for the
HART, because PMP *rekoves* access by default. At this point all of
the user memory as well as the kernel RAM are opened.
A more flexible solution for PMP configuration will follow.
The old implementation used the default ld.script for the kernel side
which did not obey the memory.ld limits whatsoever.
Also, provide the user space addresses from the linker script to get rid
of the pre-processor macros that define (incorrect) default values for
the user space composition.
Some of the configuration options have changed, so update this
config file accordingly.
In this example config, the following hart configuration takes
place:
hart1: 0xafb00000 (Another NuttX)
hart2: unused
hart3: 0x80200000 (u-boot and Linux kernel)
hart4: 0x80200000 (u-boot and Linux kernel)
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
By default SAME70_QMTECH board does not have CD signal routed to
SAME70. The HW rework can be done to enable CD signal. Clarify
description of SD card connector.
Change configuration of CD pin to get auto unmount work correctly
Signed-off-by: Petro Karashchenko <petro.karashchenko@gmail.com>
There is no such section. Instead, place the object mpfs_head.o at the start of
the text.
Put mpfs_head.o directly into the arch library; there is no need to define
it separately in HEAD_ASRC.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
iSerialNumber field in the device descriptor can be used to determining the
board when multiple boards connected to the same host. So add feature to change
serial string by board unique ID dynamically.
To use this feature, user must be implement the board_usbdev_serialstr() logic.
refs #13909
includes following parts:
add support of sparc in arch/Kconfig
add support of sparc in boards/Kconfig
add sparc dir in arch, add sparc dir in boards
add support of sparc in libs/libc/machine
modify all the coding style problem about saprc
Add the rest of the OpenSBI code to .text.sbi -section. They belong
to there. This frees up some space in the very limited eNVM.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
RAM is expected to start from 0x08000000, not from
0x80000000 in this case. DDR starts from 0x80000000.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
It’s an RP2040 based device with some interesting features:
+ small form factor (18x21.3mm)
+ 8 MByte Flash
+ RGB LED
+ Reset Button
+ USB-C
- reduced pin-header
Support in derived from: boards/arm/rp2040/raspberrypi-pico
Location: boards/arm/rp2040/pimoroni-tiny2040
This PR renames `tools/Makefile.*` to have the `.mk` extension. This PR also updates `README.md` and other files that references the other files.
Note: Skipped Makefile.host for this PR since it caused failures in CI for the sim build
By using a standard extension for Makefiles (https://www.file-extension.info/format/mk), editors will auto-format files.
This change will also improve developer ergonomics when searching for specific files
Verified locally that build still works, CI will verify more!
Polarfire Icicle board has only (128K - 256) bytes for the bootloader
in the non-volatile eNVM. This space is barely enough for running NuttX.
If OpenSBI is selected, it will be placed in DDR. This all means the
nuttx.bin file grows into gigabyte size, filling the unused space (ddr -
envm) with zeroes.
The memory layout is as follows:
MEMORY
{
ddr (rx) : ORIGIN = 0x80000000, LENGTH = 4M
envm (rx) : ORIGIN = 0x20220100, LENGTH = 128K - 256
l2lim (rwx) : ORIGIN = 0x08000000, LENGTH = 1024k
l2zerodevice (rwx) : ORIGIN = 0x0A000000, LENGTH = 512k
}
OpenSBI library is used as a separate binary, which is stored into
eMMC or SD-card. It is then loaded into its precise location in DDR.
Thus, we separate OpenSBI from NuttX and end up with two images
by utilizing the objcopy options:
--only-section=sectionpattern (-j in short)
--remove-section=sectionpattern (-R in short)
This is only valid when CONFIG_MPFS_OPENSBI is set.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
since VNC server is very useful even without NX:
1.Replace nxgl_coord_t with fb_coord_t
2.Replace nxgl_rect_s with fb_area_s
3.Remove nxgl_xxx function call
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Summary:
- I noticed that most of nsh commands are disabled by default
due to the recent changes for CONFIG_MM_SMALL=y in apps.
- This commit re-enables some nsh commands.
Impact:
- None
Testing:
- Tested with QEMU
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Some incompatibilities exist between the encryption block of the SPI
Flash peripheral and the algorithms of some file systems. LittleFS is
currently the only supported file system which is known to work
correctly when Flash Encryption is enabled.
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
Add a pinmap header for mpfs to be able to configure MSSIO GPIOs
This also adds Kconfigs for some different chip/package types of the PolarFire SOC
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
This fixes problems with DDR training sequence on aries m100pfs board
- Set LIBERO_SETTING_RPC_ODT_* to 6, which matches 40 ohm. Originally it was 120 ohm (2)
- Set BCLKSCLK_OFFSET value to 5, which matches icicle board setting
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
1. Fix the issue that Wi-Fi can't connect to some special routers occasionally.
2. Update Wi-Fi driver code to fix issue of failure to send pkt.
3. Replace software random with hardware random
since all NX and VNC initialization should be initiated from
user space through BOARDIOC_NX_START and BOARDIOC_VNC_START
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Update the cache settings for the Aries m100pfsevp board. This
assigns scratchpad ways for this board as well, as seen in the
commit 491ae6c.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
OpenSBI may be compiled as an external library. OpenSBI commit d249d65
(Dec. 11, 2021) needs to be reverted as it causes memcpy / memcmp to
end up in the wrong section. That issue has yet no known workaround.
OpenSBI may be lauched from the hart0 (e51). It will start the U-Boot
and eventually the Linux kernel on harts 1-4.
OpenSBI, once initialized properly, will trap and handle illegal
instructions (for example, CSR time) and unaligned address accesses
among other things.
Due to size size limitations for the mpfs eNVM area where the NuttX
is located, we actually set up the OpenSBI on its own section which
is in the bottom of the DDR memory. Special care must be taken so that
the kernel doesn't override the OpenSBI. For example, the Linux device
tree may reserve some space from the beginning:
opensbi_reserved: opensbi@80000000 {
reg = <0x80000000 0x200000>;
label = "opensbi-reserved";
};
The resulting nuttx.bin file is very large, but objcopy is used to
create the final binary images for the regions (eNVM and DDR) using
the nuttx elf file.
Co-authored-by: Petro Karashchenko <petro.karashchenko@gmail.com>
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Assign ways to L2 zerodevice. L2 zero device is used for
the scratchpad functionality. The area may be used for the
harts communicating to each other.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Move MCUboot bootloader implementation to samv7 common folder. This drop
all duplicated code and unify implementation.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This introduce common folder structre and rework scripts & tools
files. The linker scripts were reorganized to use best the current
infrastructure which uses a template to create a final samv7.ld
file based in the current SoC memories and bootloader definitions.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
After define memory sizes for samv7 it is possible unify linker scripts.
This add necessary changes to perform such operation.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Current samv7 platform does not define SoC memories sizes. This define
both internal flash and sram memories sizes and update all defconfig
files.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
1. If CONFIG_SCHED_INSTRUMENTATION_SWITCH is enabled, then these additional interfaces are expected:
sched_note_suspend
sched_note_resume
at the same time，If CONFIG_SMP is enabled，then expected：
sched_note_cpu_pause
sched_note_cpu_paused
sched_note_cpu_resume
sched_note_cpu_resumed
2. other board if enable SCHED_INSTRUMENTATION，SCHED_INSTRUMENTATION_SWITCH to defconfig.
Summary:
- This commits adjusts the following settings for spresense
- CONFIG_FAT_MAXFNAME : 255 to 128
- CONFIG_NAME_MAX : 765 to 128
Impact:
- None
Testing:
- Tested with spresense:wifi_smp
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
2.fix some files to fix compile warning
3.remove blueteeth header files, which are not used in nuttx core.
4.fix configs and add lost files
5.update defconfig, remove useless items
6.fix compile warning for nuttx phyplus
7.delete useless: ble, h4, zblue defconfig files form phyplus configure folder
8.fix file format check error on phyplus source code
9.fix phyplus kconfig param error
10.update configure file for nuttx
Set default console port to USART1. This allows easy access to serial
console by embedded debug CDC-ACM driver.
The README is updated with correct information about PB04 use once
samv71-xult can only be debugged using SWD mode. This means that it is
safe use CDC-ACM as default serial console.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Updates defconfig for example application to take the advantage of DMA
support and Timer/counter trigger.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
we have many different hostfs implementation now, so it's better
to select the implementation explicitly, just like what we have
done for arm(FS_HOSTFS vs. ARM_SEMIHOSTING_HOSTFS).
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
src/mpfs_emmcsd.c: In function 'mpfs_board_emmcsd_init':
Error: src/mpfs_emmcsd.c:72:40: error: 'SDIO_SLOTNO' undeclared (first use in this function)
finfo("Initializing SDIO slot %d\n", SDIO_SLOTNO);
^~~~~~~~~~~
src/mpfs_emmcsd.c:72:40: note: each undeclared identifier is reported only once for each function it appears in
Error: src/mpfs_emmcsd.c:83:55: error: 'SDIO_MINOR' undeclared (first use in this function); did you mean 'SHRT_MIN'?
finfo("Bind SDIO to the MMC/SD driver, minor=%d\n", SDIO_MINOR);
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
- Add defconfig and board specific files
- Create mpfs/common for code which is shared between MPFS boards.
- Add support for GPIO driven EMMCSD mux.
- Move DDR Libero definitions from arch to boards.
Signed-off-by: Jani Paalijarvi <jani.paalijarvi@unikie.com>
Gregory Nutt has submitted the SGA
Haltian Ltd has submitted the SGA
as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
script.
These functions are strongly declared and thus will be used instead of
any other implementation. Furthermore, necessary Kconfig options are
selected to avoid building those function from NuttX's C library.
Signed-off-by: Abdelatif Guettouche <abdelatif.guettouche@espressif.com>
This commit adds board level support for Analog Front End driver to
SAME70 Xplained boaed. Example application can be run via adc
configuration.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
1. Wi-Fi and BLE use common PHY functions.
2. Fix Wi-Fi & BLE coexist adapter error.
3. Update esp-wireless-drivers-3rdparty, provide coexist protection for connection.
E51 may configure the L1 and L2 caches. Once configured,
no reconfiguration is possible after hardware reset is
issued.
L2 is 16-way set associative with write-back policy. The
size 2 MB, from which 1 MB is utilized with the values
provided here. That's a total of 8 ways. The rest of the
L2 is left out for the bootloader usage.
mpfs_enable_cache() first checks the bootloader usage
doesn't overlap with the cache itself, thus providing a
set of functional values.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
This commit brings 3 fixes/improvements applied to the Kconfig options
for SPI Flash file system support on board bring-up:
- (925e8f9) Optionally mount SPI Flash MTD on bring-up
- (f74c6f7) Transform SPI Flash FS deps into reverse deps
- (9056cab) Select MTD_SMART if SmartFS is selected for SPI Flash MTD
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
Currently, when no file system is selected, the "choice" lists zero
entries, which is very confusing to the user. To handle this, the
"choice" options have their dependencies ("depends on") transformed into
reverse dependencies ("select").
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
Give the user the option to simply register the SPI Flash MTD as a
device node on /dev.
Currently, this is achievable only when SmartFS (which is the default FS
option) is disabled by force. This behavior is fixed by using the
"optional" Kconfig keyword, which makes the "choice" selectable.
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
This adds DDR training. The training has a small chance of failing,
and then the training is restarted.
DDR training cannot be done meaningfully while the software is
in DDR. If the system is intended to run from eNVM, like a
bootloader, the linker script should be tuned to utilize the envm
region as follows:
envm (rx) : ORIGIN = 0x20220100, LENGTH = 128K - 256
l2lim (rwx) : ORIGIN = 0x08000000, LENGTH = 1024k
256 bytes are reserved for the system; The fixed block may be
installed from the 'hart-software-services' -repository:
https://github.com/polarfire-soc/hart-software-services.git
For example, the 256-byte image: hss-envm-wrapper-bm1-dummySbic.bin
may be prepended on the nuttx bootloader image in the following
manner:
cat hss-envm-wrapper-bm1-dummySbic.bin > nuttx_bootloader.bin
cat nuttx.bin >> nuttx_bootloader.bin
riscv64-unknown-elf-objcopy -I binary -O ihex --change-section-lma
*+0x20220000 nuttx_bootloader.bin flashable_image.hex
This provides an image 'flashable_image.hex' that may be flashed on
the eNVM region via Microsemi Libero tool.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Gregory Nutt has submitted the SGA
Florian Olbrich has submitted the ICLA
as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Since the tests were removed from the drivers, there is no need for
these defconfigs anymore.
Signed-off-by: Abdelatif Guettouche <abdelatif.guettouche@espressif.com>
-march=rv64gc -mabi=lp64 does not resolve lib paths for
riscv64-unknown-elf-gcc resulting in lib not found errors.
Changing it to -march=rv64imafc -mabi=lp64f that is the default
used in Sipeed repositories.
Signed-off-by: Matheus Castello <matheus@castello.eng.br>
Gregory Nutt has submitted the SGA
Elfaro Lab SL has submitted the SGA
as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
