only break out the continuous send if IP stack has no data to send to avoid
tx being constantly interrupted by RX
Signed-off-by: chao.an <anchao@xiaomi.com>
* arch/arm/src/tiva/common/tiva_lowputc.c
(tiva_lowsetup):
For each UART, if Kconfig enables RTS/CTS (e.g.,
CONFIG_UART0_IFLOWCONTROL and/or CONFIG_UART0_OFLOWCONTROL),
configure the corresponding GPIO(s).
* arch/arm/src/tiva/common/tiva_serial.c:
(struct up_dev_s):
If CONFIG_SERIAL_IFLOWCONTROL, add a bool field 'iflow'. If
CONFIG_SERIAL_OFLOWCONTROL, add a bool field 'oflow'. This is
inspired by the implementation for kinetis.
(g_uart0priv, g_uart1priv, g_uart2priv, g_uart3priv, g_uart4priv,
g_uart5priv, g_uart6priv, g_uart7priv):
If Kconfig enables RTS/CTS for a UART (e.g.,
CONFIG_UART0_IFLOWCONTROL thru CONFIG_UART7_OFLOWCONTROL), set
the corresponding iflow and/or oflow flag(s).
(up_setup):
Check the above-mentioned iflow and oflow flags and set or unset
the RTSEN and/or CTSEN bits in the UART's CTL register to enable
the feature.
* libs/libc/misc/lib_getrandom.c, in function getrandom():
We were assigning the return value of _NX_READ() to nbytes, a
variable of the unsigned type size_t. Note that _NX_READ() resolves
to either read() or nx_read(), both of which return the signed type
ssize_t to indicate either the number of bytes read successfully
(>= 0) or an error (< 0). Then we were testing for a negative
size_t value, a condition that can never occur. The end result is
that if an error occured in _NX_READ(), it would never be detected
and getrandom() would return some large positive value. This bug is
corrected by assigning the return value of _NX_READ() to a new local
variable, ret, of size ssize_t.
The "p" format specifier already prepends the pointer address with
"0x" when printing.
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
The "p" format specifier already prepends the pointer address with
"0x" when printing.
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
The "p" format specifier already prepends the pointer address with "0x"
when printing.
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
The field of first cluster under LFN directory entry must be 0x0000. If
it is set a value other than 0, it causes a problem where the long file
name entry cannot be found on a Windows PC and the short file name is
always used. In addition, correct the macro error in big endian.
Sync driver interfaces, also fixes the handling of special pin value for
esp32s2_gpio_matrix_in and esp32s2_gpio_matrix_out functions
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
RX/TX shared free queue on bcmf implementation, if TX occupies the
free queue completely, RX will trigger read abort because it cannot
alloc buffer successfully from the shared free queue. This commit will
limit the sending entries of tx and prevent rx triggering abort
Signed-off-by: chao.an <anchao@xiaomi.com>
Make use of XCHG/BSWAP on x86, REV16 and REV on ARMv6-m and above,
and whatever other optimized instructions on other platforms.
Defines extra CONFIG variables, and removes the unused functions for
endian-swapping. Fixes some oversights in using the macros.
Starting the rptun with the autostart flag set will cause significant
delays at the boot, as it will wait for the master to be up. U-boot/linux
combination may take more than 10 seconds to boot to the point where the
rpmsg bus is initialized.
For now, the user needs to initialize the rptun separately, for example,
by issuing the following command:
rptun start /dev/rptun/mpfs-ihc
This command will also block if started before the rpmsg bus master is up.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Move the linker defined symbols to a separate file, so they can be
accessed without pulling in everything from riscv_internal.h and
whatever it includes (e.g. syscall.h drags in a lot).
