stm32h7 RTC and friends support
* stm32h7:Removed f7 in file path
* stm32f7:Fix overwritten IRQ enabled
System boot order calls clock_initialize then up_initalize.
clock_initialize was setting up the alarm IRQ
up_initalize is initializing the NVIC.
This most likely worked in the past due to a bug in the
NVIC init code that failed to clear the Interrupt enables.
That was fixed in 510b0f7e arch/arm/src: Correct all ARMv7-M
architectures. Interrupts were not be disabled correctly
on power up.
* stm32h7:Ported over F7 RTC
* nucleo-h743zi:Add RTC
Approved-by: Gregory Nutt <gnutt@nuttx.org>
serial single-wire: add possibility to specify pull-up instead of open drain
Approved-by: David Sidrane <david.sidrane@nscdg.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Master
* Revert "Merged in yanqil-br/feature-multi_chan_pwm (pull request #973)"
This reverts commit aef0e0b5383b99cad1f0d5f8e612fd5463252daf.
* arch/arm/src/{stm32/stm32f7/stm32h7/stm32l4}/stm32_pwm.c: configure multi-channel duty only if channel specified. This allows you to update duty cycle for a single channel
* nucleo-f303re/configs: add basic NSH configuration
* nucleo-f303re/configs/pwm: enable console on UART2 and set entry point to nsh_main
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Move boards to boards folder
* boards: rename configs folder to boards
This is the proposed layout after the change:
boards: - folder containing board folders
<board>: - name of each board
drivers: - extra drivers specific for platform
include: - header files for the boars
scripts: - extra scripts specific for platform
src: - board specific code
tools: - extra tools specific for platform
<config>: - board specific configuration(s)
Note:
<xxx> names are dependent on platform
This is a logical change to aim to the arch layout but this is a
huge change it should be done in several steps to lower the risk.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Kconfig: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Makefile: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Makefile.*: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Make.defs: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .sh: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .mk: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .c & .h: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .bat: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
stm32 h7 Add ADC and a few fixes for timer and Serial
* stm32h7:Fix error when SINGLEWIRE or CONFIG_STM32H7_SERIALBRK_BSDCOMPAT defined
* stm32h7:time fixed compile errors with TIM13,TIM14, TIM7
* stm32h7:Added ADC Driver
* stmh7x3:Added ADC pins to pin map
* stm32h7:Added ADC clocking
* nucleo-h743zi:Add ADC
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Port STM32F7 I2C to STM32F3 and STM32F0L0
arch/arm/src/stm32: port I2C IPv2 driver from F7 (only F3 chips)
arch/arm/src/stm32f0l0: port I2C IPv2 driver from F7
configs/b-l072z-lrwan1: nxlines_oled example (ssd1306)
configs/b-l072z-lrwan1: support for the I2C tool
configs/nucleo-f303ze: nxlines_oled example (ssd1306)
arch/arm/src/stm32h7/chip.h: cosmetics
arch/arm/src/stm32/chip/stm32_tim.h: cosmetics
Approved-by: Gregory Nutt <gnutt@nuttx.org>
libs/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
syscall/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
wireless/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
Documentation/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
include/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
drivers/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
sched/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
configs: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/xtensa: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/z80: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/x86: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/renesas and arch/risc-v: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/or1k: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/misoc: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/mips: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/avr: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/arm: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
