Gregory Nutt
|
4868acf27e
|
Add option to enable Aduino Due specific logic, like pull-up on UART0 RXD. Suggested by gdi@embedders.org
|
2013-10-09 07:35:00 -06:00 |
|
Gregory Nutt
|
efded598fd
|
Finally... renamed all CONFIG_DRAM_ settings to CONFIG_RAM_
|
2013-07-26 10:09:17 -06:00 |
|
Gregory Nutt
|
7c88100581
|
Fix type in the USB composite device driver
|
2013-07-04 07:47:32 -06:00 |
|
Gregory Nutt
|
b2a6338e69
|
Updates for the Sure PIC32 board
|
2013-07-03 11:39:54 -06:00 |
|
Gregory Nutt
|
242b459b05
|
Fix SAM34 interrupt handling for ports D-F; fix MISO logic in Arduino Due touchscreen driver
|
2013-07-03 08:12:45 -06:00 |
|
Gregory Nutt
|
c8a4f69a69
|
Several fixes to get a clean compile of the Arduino touch screen
|
2013-07-02 13:52:09 -06:00 |
|
Gregory Nutt
|
d6db74e581
|
Correct port direction for Arduino MISO signal
|
2013-07-02 12:37:20 -06:00 |
|
Gregory Nutt
|
d09fd9a9ca
|
Flesh out a few missing pieces for the Arduino ITEAD TFT shield
|
2013-07-02 11:36:48 -06:00 |
|
Gregory Nutt
|
3c36e6e8b5
|
Add support for touchscreen on ITEAD Arduino shield. Untested
|
2013-07-02 08:25:53 -06:00 |
|
Gregory Nutt
|
5f066efd2d
|
Add a general bit-bang SPI lower-half driver and implement the bit-bang driver for the Arduino ITEAD TFT shield
|
2013-07-01 16:50:16 -06:00 |
|
Gregory Nutt
|
a82077e0fc
|
Add a general bit-bang SPI upper-half driver
|
2013-07-01 12:23:26 -06:00 |
|
Gregory Nutt
|
17810f3e6f
|
Created new directories to hold SPI-related files
|
2013-07-01 08:11:54 -06:00 |
|
Gregory Nutt
|
6a3d1fece4
|
Add an NSH configuration for the Arduino Due; Pluse several fixes related to the Due and to the SAM3X in general
|
2013-06-28 14:32:08 -06:00 |
|
Gregory Nutt
|
fd683277c4
|
Arduino Due: Fixes to FLASH address, flash wait states, updated Comments. Now boots and runs a bit before crashing
|
2013-06-28 11:29:14 -06:00 |
|
Gregory Nutt
|
3e2fe6013c
|
Add instructions to use BOSSA to load nuttx into Due
|
2013-06-28 08:54:09 -06:00 |
|
Gregory Nutt
|
7387a6feef
|
Flesh out the Arduino Due board configuratino and integrate it with the build and configuration system
|
2013-06-27 14:24:27 -06:00 |
|
Gregory Nutt
|
288adb2f5a
|
Add peripheral configuration logic for the SAM3X/3A; Change all references to SAM3/4 SPI to SPI0 for compatibity with the SAM3X/3A which has SPI0 and SPI1; Add directory which will eventually holdl an Arduino Due port
|
2013-06-26 18:46:44 -06:00 |
|