- A pre-built IDF bootloader is used by default;
- `ESP32S3_PARTITION_TABLE` requires the IDF bootloader to be built
from sources.
- Native MCUboot also can be used to boot the device. It will be
built from sources and depends on !ESP32S3_PARTITION_TABLE.
- A pre-built IDF bootloader is used by default;
- `ESP32S2_PARTITION_TABLE` requires the IDF bootloader to be built
from sources.
- Native MCUboot also can be used to boot the device. It will be
built from sources and depends on !ESP32S2_PARTITION_TABLE.
- A pre-built IDF bootloader is used by default;
- `ESP32_PARTITION_TABLE` requires the IDF bootloader to be built
from sources.
- Native MCUboot also can be used to boot the device. It will be
built from sources and depends on !ESP32_PARTITION_TABLE.
ESP32 is supported on NuttX starting from chip revision 3.0. This,
however, didn't prevent the user from using older chip revisions,
which caused unexpected behaviors. This commit checks chip revision
before finishing booting NuttX.
This commit is intended to update the EFUSE's register content and
update related configs:
- Remove duplicated configs from `esp32_soc.h`;
- Add missing header files from APB registers;
- Add missing macro definitions from EFUSE;
- Update related code to use the new macros;
Newly added logging in `sched/task_exit.c` obsoletes the existing
ones in `arch/up_exit()`, thus remove the latter to reduce duplications.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
The RT-Timer thread may call the `start_rt_timer` function. This
function gets the spinlock with interrupts disabled to ensure
exclusive access. However, this was already being performed in the
RT-Timer thread, causing a deadlock.
Following up the 'Espressif HAL fullly integration for ESP32s2/s3'
changes in https://github.com/apache/nuttx/pull/11428
There are few missing interrupt type constants need update. So
update them to avoid the build error.
By integrating the Espressif`s HAL repository into the current
ESP32-S2 implementation on NuttX, it is possible to call functions
that makes it easier to setup the registers of the ESP32-S2,
enabling the usage of common Espressif drivers.
By integrating the Espressif`s HAL repository into the current
ESP32-S3 implementation on NuttX, it is possible to call functions
that make it easier to set up the registers of the ESP32-S3 and
enables the usage of common Espressif drivers. Please note that
Espressif's HAL repository was already being used for the Wi-Fi
driver. Then, this commit includes other source files to be used
by other drivers other than Wi-Fi and reorganize the build process.
This lower-half WS2812 LED driver uses the RMT peripheral of the
Espressif's SoCs to drive the RGB addressable LEDs. Compared to
the SPI-based implementation, it is faster!
The lower-half implementation of the RMT character driver based on
Espressif HAL enables using the RMT peripheral of ESP32, ESP32-S2
and ESP32-S3 as a common xtensa-based Espressif driver.
The RMT packages on Espressif SoCs are 4-byte long and are known as
"items". Please check the Techinal Reference Manual of the chip to
obtain more details.
1. Solve wifi may not work bug for bbpll not lock or not stable when enable RF.
2. Improved timing tuning stability on ESP32-S3.
The root cause of the issue:
The application won't re-calibrate the BBPLL clock if it's already enabled.
We add a force-recalib function in the app startup code to make sure even if
the patch is applied by OTA, the clock is still re-calibrated.
Signed-off-by: chenwen@espressif.com <chenwen@espressif.com>
The `xxx_ipv6multicast` function in each driver is not adapted to
multiple IPv6 addresses yet, and they're redundant, so try to take them
into common code.
Change:
1. Add MAC `g_ipv6_ethallnodes` and `g_ipv6_ethallrouters` in
`icmpv6_devinit` and call them in `netdev_register`
2. Add multicast MAC for Neighbor Solicitation when adding any IPv6
address, and remove them when IPv6 address is removed
3. Select `NET_MCASTGROUP` when `NET_ICMPv6` because now we need
`d_addmac` when we have ICMPv6
Note:
We want modules outside net stack to call functions like
`netdev_ipv6_add` and never touch the related MAC address, so these MAC
functions are added as internal functions to `net/netdev/netdev.h`
Signed-off-by: Zhe Weng <wengzhe@xiaomi.com>
Add registration function instrumentation API,
which can achieve instrumentation of entering and
exiting functions through the compiler's functionality.
We can use CONFIG_ARCH_INSTRUMENT_ALL to add instrumentation for all
source, or add '-finstrument-functions' to CFLAGS for Part of the
source.
Notice:
1. use CONFIG_ARCH_INSTRUMENT_ALL must mark _start or entry noinstrument_function,
becuase bss not set.
2. Make sure your callbacks are not instrumented recursively.
use instrument_register to register entry function and exit function.
They will be called by the instrumented function
Signed-off-by: anjiahao <anjiahao@xiaomi.com>
1. Configurable mapping of virtual address to psram physical address
2. Access SPIRAM memory at high physical address through bank switching
Signed-off-by: chenwen@espressif.com <chenwen@espressif.com>
