Hardware flow control for serial requires the usage of DMAC channels
which is not yet supported for SAMv7 MCU. However the same config option
CONFIG_SERIAL_IFLOWCONTROL is also used for USB CDC/ACM flow control which
works well. Therefore the warning message should be raised only if
flow control is configured for USART driver and not for USB CDC/ACM.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
A list of breaking changes:
- SoftDevice libraries was renamed and libaries are now cmpatible with all platfroms with a given faimily.
- The random number generator was decoupled from the controller and must now be provided by the user.
We use arc4random_buf NuttX API for this.
- sdc_support_ API must be called before sdc_cfg_set()
- update public API terms to Bluetooth Core Specification v5.3 (mainly change slave/master to central/peripheral)
NuttX NRF52 configuration options properly updated.
- BLE features are supported only if the proper BLE role is selected
- sdc_hci_evt_get() and sdc_hci_data_get() have been replaced by sdc_hci_get()
This commit adds configurable fault protection to SAMv7 PWM driver.
The fault input can be used from peripherals as ADC or GPIO inputs.
Inputs from GPIO have configurable polarity (high or low). The PWM output
is automatically set to zero if fault input is active and restored
if fault input is not actived.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
- Add retry timeout to prevent inifinite loop
- Change the register operation of power control
- Add exclusive control by semaphore into some functions
- Add short delay until power control is reflected
This commit enhances ADC and PWM drivers with option to trigger ADC
conversion with events generated by PWM comparison units.
The generation of PWM events is handled by comparison units set up from
Kconfig option SAMV7_PWMx_TRIGn. ADC triggering from PWM can be selected
by AFECn_PWMTRIG option.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
SAMv7 PWM driver supports complementary PWM output if both pins (H and L)
are defined and configured. This commit adds a configuration option to
configure the complementary L pin.
The pin definition has to be provided by board level support.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Summary:
- I noticed that there are two kinds of descriptors for imxrt_enet.c
- The first one is the legacy descriptor and its size is 8bytes.
- The second one is the enhanced descriptor and its size is 32bytes.
- In both cases, we can not use a descriptor chain like stm32.
- Considering cache line alignment, the second one is perfect because
one descriptor fits the Cortex-M7 cache line which would fix networking
stability issues in d-cache write-back mode.
Impact:
- imxrt ethernet in d-cache write-back mode
Testing:
- Tested with ixmrt1060-evk:netnsh_dcache_wb (will be added later)
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- I noticed that CONFIG_IMXRT_ENET_ENHANCEDBD is not correctly
used though it is defined in Kconfig.
- This commit fixes this issue.
Impact:
- None
Testing:
- Tested with imxrt1060-evk:netnsh_dcache_wb (will be added later)
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
This reverts commit 62c15c03d3.
Fix warning: the choice symbol STM32_FLASH_CONFIG_G (defined at arch/arm/src/stm32/Kconfig:1275) is selected by the following symbols, but select/imply has no effect on choice symbols
- ARCH_CHIP_STM32F412ZG (defined at arch/arm/src/stm32/Kconfig:1014)
Generic drivers shoud not use architecture related config options like
CONFIG_SAMV7_PWM. This commit adds PWM pin overwrite under generic
configuration option CONFIG_PWM_OVERWRITE.
Now the overwrite can be used on other architectures as well or can be
completely disabled for SAMv7.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Commit d07792a caused a build error in sam_mcan.c file. This commit fixes
the build. The file now succesfully compiles and CAN works.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
