Some hardware needs to config this delay to write one data block, because
the hardware needs more time to wear leveling and bad block manage.
Signed-off-by: dongjiuzhu1 <dongjiuzhu1@xiaomi.com>
The implementation of up_perf_*() is in a different static library in nuttx:
Hardware: libarch.a
Software: libdrivers.a (weak function)
Since functions with weak attributes cannot be correctly replaced in multiple static libraries,
this PR will use macros to replace whether the arch supports hardware perf events
Signed-off-by: chao an <anchao@xiaomi.com>
- considering simplicity and design assumption, the reset function must work without flaw.
If it fails, there is no way to recover but to reset again. so checking return status does not
bring additional benefit
- There is unnecessary switch inside switch which is making code not too readable
Signed-off-by: mks2183 <manishsharma3134@gmail.com>
nuttx/drivers/sensors/wtgahrs2.c: In function ‘wtgahrs2_initialize’:
nuttx/drivers/sensors/wtgahrs2.c:545:22: warning: ‘%lx’ directive output may be truncated writing between 1 and 16 bytes into a region of size 14 [-Wformat-truncation=]
545 | snprintf(arg1, 16, "0x%" PRIxPTR, (uintptr_t)rtdata);
| ^~~~~
nuttx/drivers/sensors/wtgahrs2.c:545:25: note: format string is defined here
545 | snprintf(arg1, 16, "0x%" PRIxPTR, (uintptr_t)rtdata);
nuttx/drivers/sensors/wtgahrs2.c:545:22: note: directive argument in the range [1, 18446744073709551615]
545 | snprintf(arg1, 16, "0x%" PRIxPTR, (uintptr_t)rtdata);
| ^~~~~
nuttx/drivers/sensors/wtgahrs2.c:545:3: note: ‘snprintf’ output between 4 and 19 bytes into a destination of size 16
545 | snprintf(arg1, 16, "0x%" PRIxPTR, (uintptr_t)rtdata);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: chao an <anchao@xiaomi.com>
3 wire interface for ST7789 LCD controller does not use CMD/DATA pin to
specify whether data or command is send but uses 9th bit of SPI transfer.
This commit adds support for 3 wire interface to ST7789 controller.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
use workqueue for rpmsgdev poll notify to prevent
calling rpmsgdev_poll_cb in interrupt context which
will try to hold mutex in rpmsg_send
Signed-off-by: liaoao <liaoao@xiaomi.com>
Remove TABs
Fix indentation
Fix Multi-line comments
Fix Comments to the Right of Statements.
Fix nuttx coding style
Fix Comments to the Right of Statements.
support to control the opening or closing of the specified channel through the syslogmask command at runtime
Signed-off-by: yinshengkai <yinshengkai@xiaomi.com>
usage:
1. Connect Jlink, start JLinkGDBServer
JLinkGDBServer -if SWD -device stm32h743zi -speed 16000
2. Listen to the RTT port data and forward it to the virtual serial port
sudo socat -d -d PTY,link=/dev/ttyRTT0,raw,ignoreeof TCP:127.0.0.1:19021,reuseaddr
3. Read serial data
minicom -D /dev/ttyRTT0
Performance:(STM32H743, 400MHZ)
time "dd if=/dev/zero of=/dev/console bs=512 count=2048"
6.67 sec 157KB/s
Signed-off-by: yinshengkai <yinshengkai@xiaomi.com>
Take the idea from Linux's iw_handler array and esp32c3_wlan's wlan_ops_s, and make it a common logic of upper-half driver.
Signed-off-by: Zhe Weng <wengzhe@xiaomi.com>
1. Update all CMakeLists.txt to adapt to new layout
2. Fix cmake build break
3. Update all new file license
4. Fully compatible with current compilation environment(use configure.sh or cmake as you choose)
------------------
How to test
From within nuttx/. Configure:
cmake -B build -DBOARD_CONFIG=sim/nsh -GNinja
cmake -B build -DBOARD_CONFIG=sim:nsh -GNinja
cmake -B build -DBOARD_CONFIG=sabre-6quad/smp -GNinja
cmake -B build -DBOARD_CONFIG=lm3s6965-ek/qemu-flat -GNinja
(or full path in custom board) :
cmake -B build -DBOARD_CONFIG=$PWD/boards/sim/sim/sim/configs/nsh -GNinja
This uses ninja generator (install with sudo apt install ninja-build). To build:
$ cmake --build build
menuconfig:
$ cmake --build build -t menuconfig
--------------------------
2. cmake/build: reformat the cmake style by cmake-format
https://github.com/cheshirekow/cmake_format
$ pip install cmakelang
$ for i in `find -name CMakeLists.txt`;do cmake-format $i -o $i;done
$ for i in `find -name *\.cmake`;do cmake-format $i -o $i;done
Co-authored-by: Matias N <matias@protobits.dev>
Signed-off-by: chao an <anchao@xiaomi.com>
