This function fails to compile due to numerous undeclared register definitions used in cxd56_audio_bca_reg.c. This commit replaces the undefined definitions with very similar definitions recommended by GCC (differing only in some spelling).
However, I cannot be certain that this is correct. This must be reviewed, corrected, and verified by Alin Jerpelea. Please do not merge until Alin approves.
The configuration that demonstrates the failure is spresense:audio.
nrf52: add support for GPIO interrupts
nrf52: add macros to decode GPIO PIN and GPIO PORT
nrf52: various cosmetic changes
nrf52: fix GPIO P1 memory address
boards/nrf52840-dk: add support for SPI
boards/nrf52840-dk: add support for LSM6DSL sensor
boards/nrf52840-dk: add support for SX127X radio
Author: Alan Carvalho de Assis <acassis@gmail.com>
Check all .c and .h against nxstyle and fix it.
Author: Alin Jerpelea <alin.jerpelea@sony.com>
fs: smartfs: Fix over capacity write
When the remaining capacity of flash is one sector, if a new root
directory is created by file open, then the root directory's chain is
broken and it causes to SmartFS filesystem crash. Once this fatal
problem occurs, it's impossible to recover even if the system reboot.
Fix it by finally update link of root directory.
fs: smartfs: Fix buffer overrun
fs: smartfs: Fix uninitialized variable warnings
fs: smartfs: Memory leak fix
boards: cxd56xx: Update spresense board.h
- Fix PMIC assignment
- Add specific pin configurations for spresense
- Remove unnecessary definitions
arch: cxd56xx: Add ITM syslog init at startup
arch: cxd56xx: Enable DMA settings dynamically
Author: Alan Carvalho de Assis <acassis@gmail.com>
Fix small typos and check against nxstyle
Author: Gregory Nutt <gnutt@nuttx.org>
boards/arm/lpc43xx/bambino-200e/src/lpc43_appinit.c: Eliminate a warning found in build testing.
The removal of (void) from all functions whose return value has been ignored has introduced several new warnings into the build test output. For example in lpc3_appinit(), I now see this:
# define nsh_spifi_initialize() (OK)
and
nsh_spifi_initialize();
which generaterd a new warning: "warning: statement with no effect [-Wunused-value]". This commit fixes that warning.
Author: Alan Carvalho de Assis <acassis@gmail.com>
Verify all .c and .h against nxstyle, fixed the Mixed cases
Author: Alin Jerpelea <alin.jerpelea@sony.com>
cxd56xx improvements (#48)
* arch: cxd56xx: Add size limitation for I2C SCU xfer
This is a fw restriction, unroll loop because it can be transfer
up to 16 bytes.
* arch: cxd56xx: Fix lack of leave_critical_section
add the missing leave_critical_section
* arch: cxd56xx: Remove unnecessary file
this header is duplicate and we can remove it
* arch: cxd56xx: Cosmetic change
remove space after function
* arch: cxd56xx: update topreg registers
the topreg registers are updated to match the cxd5602 HW
* arch: cxd56xx: Add voltage setting for low battery notification
Add voltage setting for low battery notification
* arch: cxd56xx: Improve perfomance of SD card
Improve a problem that the clock of SD Host Controller is lower than the
expected value in SDR25 transfer mode.
* arch: cxd56xx: Cosmetic changes
cleanup to comply with coding standard
* boards: cxd56xx: Cosmetic changes
updates to comply with coding standard
* boards: cxd56xx: Fix SD card cannot mount issue
SD card cannot mount when connecting and disconnecting three times
or more due to wrong state of parameter 'initialized'.
This change enables to skip swtching initialized state when mount
failed.
* arch: cxd56xx: Add size limitation for I2C SCU xfer
This is a fw restriction, unroll loop because it can be transfer
up to 16 bytes.
* arch: cxd56xx: Fix lack of leave_critical_section
add the missing leave_critical_section
* arch: cxd56xx: Remove unnecessary file
this header is duplicate and we can remove it
* arch: cxd56xx: Cosmetic change
remove space after function
* arch: cxd56xx: update topreg registers
the topreg registers are updated to match the cxd5602 HW
* arch: cxd56xx: Add voltage setting for low battery notification
Add voltage setting for low battery notification
* arch: cxd56xx: Improve perfomance of SD card
Improve a problem that the clock of SD Host Controller is lower than the
expected value in SDR25 transfer mode.
* arch: cxd56xx: Cosmetic changes
cleanup to comply with coding standard
* boards: cxd56xx: Cosmetic changes
updates to comply with coding standard
* boards: cxd56xx: Fix SD card cannot mount issue
SD card cannot mount when connecting and disconnecting three times
or more due to wrong state of parameter 'initialized'.
This change enables to skip swtching initialized state when mount
failed.
Run all .c and .h files in last PR through nxstyle.
Author: 脚蹬破拖鞋 <happypapa@yeah.net>
Add Imxrt usdhc insert or remove detection (#43)
* Add usdhc card insertion and removal detection using interrupt for imxrt.
* Add interrupt handle when usdhc insert or remove.
Run all .c and .h files in last PR through nxstyle.
Author: macman88 <jjlange91@gmail.com>
SAME5x Ethernet Support (#25)
boards/arm/samd5e5/same54-xplained-pro/: Adds basic support for Microchip SAM E54 Xplained Pro board.
arch/arm/src/samd5e5/: Adds an Ethernet driver for the SAME5x family (based on the SAMA5 GMAC driver).
* Simplify EINTR/ECANCEL error handling
1. Add semaphore uninterruptible wait function
2 .Replace semaphore wait loop with a single uninterruptible wait
3. Replace all sem_xxx to nxsem_xxx
* Unify the void cast usage
1. Remove void cast for function because many place ignore the returned value witout cast
2. Replace void cast for variable with UNUSED macro
Author: Gregory Nutt <gnutt@nuttx.org>
Run all .h and .c files modified in last PR through nxstyle.
Author: Xiang Xiao <xiaoxiang@xiaomi.com>
Net cleanup (#17)
* Fix the semaphore usage issue found in tcp/udp
1. The count semaphore need disable priority inheritance
2. Loop again if net_lockedwait return -EINTR
3. Call nxsem_trywait to avoid the race condition
4. Call nxsem_post instead of sem_post
* Put the work notifier into free list to avoid the heap fragment in the long run. Since the allocation strategy is encapsulated internally, we can even refine the implementation later.
* Network stack shouldn't allocate memory in the poll implementation to avoid the heap fragment in the long run, other modification include:
1. Select MM_IOB automatically since ICMP[v6] socket can't work without the read ahead buffer
2. Remove the net lock since xxx_callback_free already do the same thing
3. TCP/UDP poll should work even the read ahead buffer isn't enabled at all
* Add NET_ prefix for UDP_NOTIFIER and TCP_NOTIFIER option to align with other UDP/TCP option convention
* Remove the unused _SF_[IDLE|ACCEPT|SEND|RECV|MASK] flags since there are code to set/clear these flags, but nobody check them.
arch/arm/src/sama5/sam_serial.c: uart2port in sam_serial, fix the rest of the uarts in sam_serial
boards/arm/sama5/sama5d2-xult/README.txt: Fix some minor typos
boards/arm/sama5/sama5d2-xult/include/board.h: Update UART pin disambiguation with default UARTn_RXD, _TXD
Author: Gregory Nutt <gnutt@nuttx.org>
boards/arm/stm32l4/nucleo-l432kc/Kconfig: Correct use of spaces instead of TABs in Kconfig file.
Author: Pieter du Preez <wingunder@users.noreply.github.com>
Added Kconfig pin config chooser for nucleo-l432kc USARTs. (#11)
The USART pins were hard-coded for the nucleo-l432kc. This patch makes
these pins configurable via menuconfig.
nrf52 updates
board/arm/nrf52/nrf52832-dk: use the on-board virtual COM pins as default UART0 configuration
board/arm/nrf52: initial support for the nrf52840-dk board
board/arm/nrf52: initial support for the nrf52840-dk dongle board
arch/arm/src/nrf52: add support for port 1 GPIO
arch/arm/src/nrf52: initial support for UART1
arch/arm/src/nrf52: add UICR definitions
Approved-by: Gregory Nutt <gnutt@nuttx.org>
This change was motivated by the presence of the mkimage.sh file under tools. That is the tool that created the RRLOAD binary format. That bash script has a GPL license and, hence, may not be included in an Apache-licensed project.
