It is possible that a PLIC IRQ is claimed but not completed at warm
reset. This occurs at least if there is a fault in the middle of irq
handler execution.
To recover from such situation, we can complete all IRQ:s in PLIC;
this completes any already claimed IRQ, but has no effect on IRQs
which are not claimed or not enabled.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
- Use mpfs_i2c_deinit+mpfs_i2c_init sequence to re-initialize i2c block
- Use the i2c mutex to protect the reset; in case there are several devices
on the same bus, and one of them resets the bus, reset must not occur in
the middle of another device's transfer.
- Move irq attach to the i2c_init as the irq detach is in i2c_deinit
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Ensure that there are no pending state or interrupts in the i2c controller. This removes
errors caused by deinitialize/initialize sequences in error cases.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Replace risky DEBUGASSERT()s with real sanity checks. Also,
do a few more checks as the system might occasionally fire an
interrupt if the system has been restarted while in middle of
an i2c transaction.
Yet, modify i2c_transfer() function so that up_disable_irq()
is always called at the end to better prevent ill-timed irqs.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
priv->msgid may grow past its boundaries, causing
struct i2c_msg_s *msg = &priv->msgv[priv->msgid]
to read data out of boundaris.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
As long as the GNSS feature is not used, GNSS RAM can be used as general memory.
This memory is 640KByte total, which is lower performance than the application RAM.
It is possible to locate text, data and bss into GNSS RAM and to use as heap area.
Current mmu_flush_cache() hook lacks the reg param which needed by
some targets. So this PR adds the param and update existing targets
using that hook.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
Enable with ./tools/configure.sh -l esp32-devkitc:dac
DAC channel 0 = GPIO 25
DAC channel 1 = GPIO 26
default path: /dev/dac0
Resolution 8 bits = values 0~255
Voltage: 0~Vref
The reference voltage 'Vref' here is input from the pin VDD3P3_RTC
which ideally equals to the power supply VDD (3.3V).
Weak function sometimes can't have strong implementation linked.
This patch uses NUTTSBI_LATE_INIT config and normal function instead
to avoid those issues.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
The RPTUN_PING option has been replaced by RPMSG_PING but this
use for PERF_EVENTS is left behind, so replace it here as well.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
Previously NuttX runs on little core of K230, this patch allows NuttX to
run on the big core as well.
Within folder `arch/risc-v/src/k230`:
- Changes:
- CMakeLists.txt add k230_hart.c to sources list
- Make.defs add k230_hart.c to sources list
- chip.h add inclusion to k230_hart.h etc
- k230_irq.c move sbi_late_init() to k230_hart.c
- k230_start.c add support to run on big core
- hardware/:
- k230_memorymap.h add T-Head C908 specific CSR
- Additions:
- k230_hart.c sbi_late_init w/ hart initialization
- k230_hart.h header file
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
add defintions for vector extension and additional user-mode
extension fields for MSTATUS and SSTATUS registers.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
Adding CMakeLists.txt files to support CMake build system.
Note that only FLAT build works now due to limitations of current
CMake build system.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
SAMA5D2 has UART (TX/RX only) and FLEXCOM USART (with control pins).
UART has only TX/RX, so if I try to use flow control with FLEXCOM USART,
there is no register definition on the UART side and get a compilation error.
Signed-off-by: Takeyoshi Kikuchi <kikuchi@centurysys.co.jp>
Commit 03e5c02 introduced option to have both standard SPI and QSPI
in SPI mode on one system. However this change broke the appearance of
QSPI driver configuration menu entry in menuconfig as it was dependent
on !SAMV7_QSPI_IS_SPI (which is now true for all MCUs having standard
SPI ability in QSPI driver).
This change makes sure the menu is correctly shown when QSPI driver
used.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
This adds support for creating an early frame buffer and primatives for
writing to this frame buffer as a console. This does require the font
infrastructure as well as multiboot2.
Additionally this can now be used with a UEFI bootloader long as it
boots NuttX via Multiboot2. There does seem to be a PCI interrupt
issue when running in UEFI mode.
I was able to boot my laptop using this and see PCI devices enumerate.
Signed-off-by: Brennan Ashton <bashton@brennanashton.com>
x86_64: Add conditionals around the multiboot framebuffer
After warm reset the interrupt source in the HW block is not explicitly
cleared, thus once the interrupt source is enabled the old / stale interrupt
fires immediately.
This causes a DEBUGASSERT() failure on line 808 mpfs_spi_unload_rx_fifo:
DEBUGASSERT(nwords > 0);
This commit fixes building native MCUboot from sources by getting
the required sources from `esp-hal-3rdparty` repository and enable
building MCUboot and using it as the 2nd stage bootlaoder.
- A pre-built IDF bootloader is used by default;
- `ESP32C3_PARTITION_TABLE` requires the IDF bootloader to be built
from sources.
- Native MCUboot also can be used to boot the device. It will be
built from sources and depends on !ESP32C3_PARTITION_TABLE.
- A pre-built IDF bootloader is used by default;
- `ESP32S3_PARTITION_TABLE` requires the IDF bootloader to be built
from sources.
- Native MCUboot also can be used to boot the device. It will be
built from sources and depends on !ESP32S3_PARTITION_TABLE.
- A pre-built IDF bootloader is used by default;
- `ESP32S2_PARTITION_TABLE` requires the IDF bootloader to be built
from sources.
- Native MCUboot also can be used to boot the device. It will be
built from sources and depends on !ESP32S2_PARTITION_TABLE.
- A pre-built IDF bootloader is used by default;
- `ESP32_PARTITION_TABLE` requires the IDF bootloader to be built
from sources.
- Native MCUboot also can be used to boot the device. It will be
built from sources and depends on !ESP32_PARTITION_TABLE.
Simple boot is a method of booting that doesn't depend on a 2nd
stage bootloader. Please note that some of the ESP-IDF bootloader
features are not available using simple boot, such as partition
tables and OTA: most of these features are implemented in NuttX
and MCUboot.
This commit refactors DAC driver. The functionality remains the same
but driver start up is now done in dac_setup (after application called
open function) instead of sam_dac_initialize (called from BSP). This
ensures that driver does not take resources (timer, interrupt) until
opened. Implementation of dac_shutdown is also provided, therefore
the driver frees resources once closed.
This change is consistent with other drivers implementation.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
USART peripheral can work in SPI mode as well. This commit adds support
for such functionality. Only 1 slave device is supported by the
peripheral therefore board level does not have to ensure correct CS
setup.
The usage of the peripheral is the same as with other SPI drivers.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>