1.It make sense to let Toolchain.defs give the default value
2.The board can still change if the default isn't suitable
3.Avoid the same definition spread more than 200 Make.defs
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: Ic2649f1c7689bcf59c105ca8db61cad45b6e0e64
Make.defs under board folder can still overwrite the default as needed
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: I1c300a8ace4b54d475ef8d398661ed65ca273a2e
so all boards support uClibc++/libc++ automatically
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: Ibe6fafbec57f7acb26ea6188a3e9923ea82295c5
so the lower half driver don't need include the specific board.h
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: Icf6638a6865bac42150b5957376e55909f041d40
so the lower half driver don't need include the specific board.h
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: I2ff5c30049a5c5e8ee90baea56e9f4cb1a8a4f87
Summary
The naming standard at https://cwiki.apache.org/confluence/display/NUTTX/Naming+FAQ requires that all MCU-private files begin with the name of the architecture, not up_.
This PR addresses only these name changes for the up_*.h files. There are only three, but almost 1680 files that include them:
up_arch.h
up_internal.h
up_vfork.h
The only change to the files is from including up_arch.h to arm_arch.h (for example).
The entire job required to be compatible with that Naming Convention will also require changing the naming of the up_() functions that are used only within arch/arm and board/arm.
Impact
There should be not impact of this change (other that one step toward more consistent naming).
Testing
stm32f4discovery:netnsh
So call 'make EXTRAFLAGS=-Wno-cpp' could suppress the warnings with pre-processor
directive #warning in GCC.
Change-Id: Iaa618238924c9969bf91db22117b39e6d2fc9bb6
Signed-off-by: liuhaitao <liuhaitao@xiaomi.com>
* arch/arm/src/nrf52/hardware/nrf52_twi.h: fix typo
* arch/arm/src/nrf52/nrf52_i2c.c: add interrupts support and some debug messages
* boards/arm/nrf52/nrf52840-dk: add support for hts221 and lsm303agr; boards/arm/nrf52/nrf52840-dk: fix issues noted by nxstyle
nrf52: add support for GPIO interrupts
nrf52: add macros to decode GPIO PIN and GPIO PORT
nrf52: various cosmetic changes
nrf52: fix GPIO P1 memory address
boards/nrf52840-dk: add support for SPI
boards/nrf52840-dk: add support for LSM6DSL sensor
boards/nrf52840-dk: add support for SX127X radio
nrf52 updates
board/arm/nrf52/nrf52832-dk: use the on-board virtual COM pins as default UART0 configuration
board/arm/nrf52: initial support for the nrf52840-dk board
board/arm/nrf52: initial support for the nrf52840-dk dongle board
arch/arm/src/nrf52: add support for port 1 GPIO
arch/arm/src/nrf52: initial support for UART1
arch/arm/src/nrf52: add UICR definitions
Approved-by: Gregory Nutt <gnutt@nuttx.org>
