ieee802154: Simplifies notify() and rxframe() calls to a single notify() call. dataind's and all other "notifs" are now "primitives" which aligns with standard terminology
* mac802154: Adds missing breaks from case statement
* sixlowpan: Fixes bad logic where ACK is not requested if address is not a broadcast
* ieee802154: Simplification of "notifs" and "datainds" to generic primitives passed via a single notify call to the layer above the MAC
* Directories.mk should reference CONFIG_WIRELESS instead of CONFIG_DRIVERS_WIRELESS
* xbee_netdev: Network must be locked when calling sixlowpan_input
* sixlowpan: Reassembly buffer can't be freed if provided by radio driver
* sixlowpan: Don't free IOB if there is an error processing it as the MAC will try to pass it along to another receiver
* ieee802154: Adds basic logging to ieee802154_primitive.c
* Minor fixes after rebase
* xbee: Adds AT query timeout to retry if XBee doesn't respond to request
* same70-xplained: Adds Xbee support. Makes mikroBus slot Kconfig 'choice'
* mac802154: Removes unused function declaration
* drivers/mrf24j40: Fixes compilation error using . operator rather than -> operator
* mac802154_device: Changes a few mac802154_primtive_free's to ieee802154_primitive_free() and changes notif to primitive in a couple places.
* mac802154: Adds promiscous mode logic to bypass parsing of incoming frames. MAC char device also checks for promiscous mode and passes whole frames including header and FCS to the application if promiscous mode is enabled.
* sixlowpan: Fixes logic to correctly check if packet is large enough to include header. This would cause packets to be considered too small when they are sufficiently sized.
* sixlowpan: Fixes forwarding logic to use forwarding device rather than received device to look up destination link layer address
* net/ipforward: Fixes typo that caused build error when IP forwarding was enabled with CONFIG_NET_ICMPv6_NEIGHBOR enabled as well.
* configs/same70-xplained: Simple spelling fix
Approved-by: Gregory Nutt <gnutt@nuttx.org>
drivers/wireless: Adds XBee S2C (802.15.4 firmware) support. XBee driver emulates mac802154 interface
* drivers/wireless/xbee: Adds xbee_netdev. Very similar to mac802154_netdev
* configs/same70-xplained: Starts adding support for XBee radio
* drivers/wireless/ieee802154/xbee: More structuring of XBee driver
* drivers/wireless/ieee802154/xbee: More Xbee work. Starts adding support on Clicker2
* drivers/wireless/ieee802154/xbee: More XBee MAC code
* configs/clicker2-stm32: More work to add XBee radio support
* drivers/wireless/ieee802154/xbee: Most of driver is now structured. No build errors
* configs/clicker2-stm32: Adjustments to XBee click module support
* drivers/xbee: Changes md_ prefix to xd_ prefix for xbeenet_driver_s fields
* drivers/xbee: XBee network device now passes MAC events via IOCTL
* drivers/xbee: Support querying device for parameters, setting parameters, and structures association/startpan logic
* configs/clicker2-stm32: Fixes Xbee lower half ATTN poll logic
* drivers/xbee: Removes dependce on CONFIG_IEEE802154_NETDEV
* drivers/xbee: Supports MAC RESET.request primitive
* drivers/xbee: Exposes generic AT query to the rest of driver
* drivers/xbee: Sets local values when writing setting change to Xbee device
* drivers/xbee: Finish association logic
* drivers/xbee: Adds xbee_get_mhrlen( ) allocating enough space for API frame header to frame
* drivers/xbee: Finishes transmit/receive logic
* drivers/xbee: Fixes xbee_netdev to match logic in mac802154_netdev.c
* drivers/xbee: Rearranges logic to prevent a loop condition where recursion could potentially occur to the point of deadlocking the system
Approved-by: Gregory Nutt <gnutt@nuttx.org>
