This patch adds inter-processor interrupt support using K230 mailbox
device to improve the RPMsg efficiency. The polling logic has been
dropped.
Major changes:
- in arch/risc-v/include/k230:
- irq.h add IRQ for IPI devices
- in arch/risc-v/src/k230:
- Kconfig add IPI related config, increase polling delay
- Make.defs add k230_ipi.c to CHIP_SRCS
- k230_hart.c fix typo, add notes of zero MISA reading w/ NUTTSBI
- k230_irq.c use K230_PLIC_IRQS as ext IRQ limit to support IPI
- k230_rptun.c use IPI instead of polling
- in boards/risc-v/k230/canmv230/configs
- master enable IPI support
- remote enable IPI, TMPFS, RPMSGFS etc
New additions:
- in arch/risc-v/src/k230:
- k230_ipi.h add K230 IPI related defintions
- k230_ipi.c add K230 IPI driver
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
-- Detecting CXX compile features
-- Detecting CXX compile features - done
arm-none-eabi-gcc: error: -Wstrict-prototypes: No such file or directory
arm-none-eabi-gcc: error: -Wstrict-prototypes: No such file or directory
-- Configuring done
-- Generating done
Signed-off-by: chao an <anchao@lixiang.com>
This commit implements the RMT peripheral for all the supported
Espressif's RISC-V devices. It also implements the support for the
WS2812 addressable RGB LED using the RMT peripheral.
This patch revises `k230_hart.[ch]` by:
- revising big core boot/stop control.
- making k230_hart_is_big() available in S-mode.
- adding more comments.
This patch also revises the `ld-kernel.script` so that to match the
latest MMU pgtable design.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
K230 chip has two T-Head C908 RiscV cores, previously we run NuttX
on either little or big cores. This patch runs NuttX on both cores
with OpenAMP support via the RPTUN driver.
New additions:
- in arch/risc-v/src/k230
- k230_rptun.c K230 RPTUN driver
- k230_rptun.h K230 RPTUN driver header file
- in baords/risc-v/k230/canmv230
- configs/master Build config for master node
- configs/remote Build config for remote node
- scripts/ld-rptun.script Build script for RPTUN
Major changes:
- arch/risc-v/Kconfig Select NUTTSBI_LATE_INIT upon NUTTSBI
- in arch/risc-v/include
- k230/irq.h Add UART3 IRQ defs
- in arch/risc-v/src/k230
- Kconfig Add RPTUN related config items
- Make.defs Add k230-rptun.c to sources
- hardware/k230_memorymap.h Add K230 device and CSR defs
- k230_hart.c Add hart ctrl for RPTUN
- k230_hart.h Add hart ctrl for RPTUN
- k230_mm_init.c Add Svpmbt to support RPTUN
- k230_start.c Revised to support RPMsg UART
- in boards/risc-v/k230/canmv230
- scripts/Make.defs Add RPTUN script selection
- src/canmv_init.c Add RPTUN and RPMsg_UART initialization
- in Documentation/platforms/risc-v/k230/boards/canmv230
- index.rst Add AMP usage information.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
By setting "isconsole" to false, mpfs_serial stops outputting to console.
This can be used to disable output to debug console in low level.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
It is possible that a PLIC IRQ is claimed but not completed at warm
reset. This occurs at least if there is a fault in the middle of irq
handler execution.
To recover from such situation, we can complete all IRQ:s in PLIC;
this completes any already claimed IRQ, but has no effect on IRQs
which are not claimed or not enabled.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
- Use mpfs_i2c_deinit+mpfs_i2c_init sequence to re-initialize i2c block
- Use the i2c mutex to protect the reset; in case there are several devices
on the same bus, and one of them resets the bus, reset must not occur in
the middle of another device's transfer.
- Move irq attach to the i2c_init as the irq detach is in i2c_deinit
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Ensure that there are no pending state or interrupts in the i2c controller. This removes
errors caused by deinitialize/initialize sequences in error cases.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Replace risky DEBUGASSERT()s with real sanity checks. Also,
do a few more checks as the system might occasionally fire an
interrupt if the system has been restarted while in middle of
an i2c transaction.
Yet, modify i2c_transfer() function so that up_disable_irq()
is always called at the end to better prevent ill-timed irqs.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
priv->msgid may grow past its boundaries, causing
struct i2c_msg_s *msg = &priv->msgv[priv->msgid]
to read data out of boundaris.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Current mmu_flush_cache() hook lacks the reg param which needed by
some targets. So this PR adds the param and update existing targets
using that hook.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
Weak function sometimes can't have strong implementation linked.
This patch uses NUTTSBI_LATE_INIT config and normal function instead
to avoid those issues.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
Previously NuttX runs on little core of K230, this patch allows NuttX to
run on the big core as well.
Within folder `arch/risc-v/src/k230`:
- Changes:
- CMakeLists.txt add k230_hart.c to sources list
- Make.defs add k230_hart.c to sources list
- chip.h add inclusion to k230_hart.h etc
- k230_irq.c move sbi_late_init() to k230_hart.c
- k230_start.c add support to run on big core
- hardware/:
- k230_memorymap.h add T-Head C908 specific CSR
- Additions:
- k230_hart.c sbi_late_init w/ hart initialization
- k230_hart.h header file
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
add defintions for vector extension and additional user-mode
extension fields for MSTATUS and SSTATUS registers.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
Adding CMakeLists.txt files to support CMake build system.
Note that only FLAT build works now due to limitations of current
CMake build system.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
After warm reset the interrupt source in the HW block is not explicitly
cleared, thus once the interrupt source is enabled the old / stale interrupt
fires immediately.
This causes a DEBUGASSERT() failure on line 808 mpfs_spi_unload_rx_fifo:
DEBUGASSERT(nwords > 0);
This commit fixes building native MCUboot from sources by getting
the required sources from `esp-hal-3rdparty` repository and enable
building MCUboot and using it as the 2nd stage bootlaoder.
- A pre-built IDF bootloader is used by default;
- `ESP32C3_PARTITION_TABLE` requires the IDF bootloader to be built
from sources.
- Native MCUboot also can be used to boot the device. It will be
built from sources and depends on !ESP32C3_PARTITION_TABLE.
Simple boot is a method of booting that doesn't depend on a 2nd
stage bootloader. Please note that some of the ESP-IDF bootloader
features are not available using simple boot, such as partition
tables and OTA: most of these features are implemented in NuttX
and MCUboot.
The Simple Boot feature for Espressif chips is a method of booting
that doesn't depend on a 2nd stage bootloader. Its not the
intention to replace a 2nd stage bootloader such as MCUboot and
ESP-IDF bootloader, but to have a minimal and straight-forward way
of booting, and also simplify the building.
This commit also makes this bootloader configuration as default
for esp32c3-generic target and removes the need for running
'make bootloader' command for it.
Signed-off-by: Almir Okato <almir.okato@espressif.com>
Ox64 BL808 crashes with a Page Fault when we run `getprime` then `hello`. This is caused by the T-Head C906 MMU incorrectly accessing the MMU Page Tables of the Previous Process (`getprime`) while starting the New Process (`hello`).
To fix the problem, this PR flushes the MMU Cache whenever we point the MMU SATP Register to the New Page Tables. We execute 2 RISC-V Instructions that are specific to T-Head C906:
- DCACHE.IALL: Invalidate all Page Table Entries in the D-Cache
- SYNC.S: Ensure that all Cache Operations are completed
This is derived from the T-Head Errata for Linux Kernel. More details here: https://lupyuen.github.io/articles/mmu#appendix-flush-the-mmu-cache-for-t-head-c906
Modified Files:
- `arch/risc-v/src/common/riscv_mmu.h`: If needed, `mmu_write_satp()` calls `mmu_flush_cache()` (weak function) to flush the MMU Cache. (Like for T-Head C906)
- `arch/risc-v/src/bl808/bl808_mm_init.c`: Flush the MMU Cache for T-Head C906. Extend `mmuflags` from 32-bit to 64-bit to be consistent with `mmu_ln_setentry()`.
- `boards/risc-v/bl808/ox64/configs/nsh/defconfig`: Enable `ostest` in the Build Config. Update `CONFIG_BOARD_LOOPSPERMSEC` according to `calib_udelay`.
Ubuntu stock toolchain `gcc-riscv64-unknown-elf` complains about
current CMake system (see issue#11573). This tries to fix it so
that both newer XPack and stock toolchains can be used with CMake.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
To avoid build break:
ld: riscv-none-elf/lib/rv64imafdc_zicsr/lp64d/crt0.o: in function `.L0 ':
(.text+0x8): undefined reference to `__bss_start'
ld: (.text+0x10): undefined reference to `_end'
ld: (.text+0x36): undefined reference to `main'
collect2: error: ld returned 1 exit status
Signed-off-by: chao an <anchao@lixiang.com>
Newly added logging in `sched/task_exit.c` obsoletes the existing
ones in `arch/up_exit()`, thus remove the latter to reduce duplications.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
Previously k230 kernel build needs OpenSBI wrapping for use on
target, thus leading to larger program and memory overheads.
This patch adds alternative small overhead kernel build support.
Changes:
- in arch/risc-v/src/k230:
- k230_head.S entrance renamed for sake of NUTTSBI
- k230_irq.c add M-mode handling for NUTTSBI case
- k230_mm_init.c add L3 table for smaller RAM case
- hardware/k230_plic.h add PLIC_CTRL definition
- Make.defs use CHIP_ASRCS to fix entrance selection
- in boards/risc-v/canmv230/scripts:
- Make.defs add support for NUTTSBI case
Additions:
- in boards/riscv/canmv230/:
- scripts/ld-nuttsbi.script link script for NUTTSBI case
- configs/nsbi/defconfig config for NUTTSBI case
The artifact nuttx.bin from this configuration can be used directly
on target as OpenSBI wrapping is not needed.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
fix typo
Some devices have special preparations before entering S-mode, thus
a hook is needed from NUTTSBI to give them the chance.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
Chips like K230 has ARCH_RV64 but only supports 32-bit MMIO. So using
ARCH_RV_MMIO_BITS is more proper here.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
