A sensor of this type measures the force on it, and additionally
compares the force with one or more specified thresholds. The sensor
can output the force value directly. Moreover, it's usually applied
as a press key. In that case, when it detects a force greater than
some given threshold, a corresponding event is reported.
Signed-off-by: jinxudong <jinxudong@xiaomi.com>
The memory allocated with strdup and asprintf is done via lib_malloc
so we need to use lib_free to deallocate memory otherwise the assertion
"Free memory from the wrong heap" is hit with flat mode and user separated
heap enabled mode.
Signed-off-by: Petro Karashchenko <petro.karashchenko@gmail.com>
Add COMPOSITE_DEVICES configuration so that external composite
devices can also know the maximum number of supported classes.
The default COMPOSITE_DEVICES number is 8.
Signed-off-by: zhangyuan21 <zhangyuan21@xiaomi.com>
The enumeration process for composite and non-composite devices
has a lot of duplicate code. Treating the code for composite
devices as universal enumeration code can reduce redundant code.
Signed-off-by: zhangyuan21 <zhangyuan21@xiaomi.com>
VELAPLATFO-12536
This provides the initial hooks for Flattened Device Tree support
with QEMU RV. It also provides a new procfs file that exposes the
fdt to userspace much like the /sys/firmware/fdt endpoint in Linux.
See https://www.kernel.org/doc/Documentation/ABI/testing/sysfs-firmware-ofw
Nodes in the fdt are not yet usable by the OS.
Signed-off-by: Brennan Ashton <bashton@brennanashton.com>
Signed-off-by: liaoao <liaoao@xiaomi.com>
Both the device and the pipe used the FSNODEFLAG_TYPE_DRIVER type before,
and now add an independent pipe type
Signed-off-by: yinshengkai <yinshengkai@xiaomi.com>
ni_buffer is defined in the initialized structure, put it in the data segment, it will increase the flash size
Signed-off-by: yinshengkai <yinshengkai@xiaomi.com>
when the size of the usb configuration descriptor
is a multiple of 64 integers, only for this size less than wlength,
host do need send ZLP
Signed-off-by: sunkun3 <sunkun3@xiaomi.com>
config value changed after resetconfig was executed
endpoint will stay disable state after setinterface cmd
Signed-off-by: sunkun3 <sunkun3@xiaomi.com>
unbind will call the adb_char_on_connect interface to wake up the adbd task,
adbd will then access the adb device and fail to return, at this time it will
close the adb device, we can do the final memory release operation in the
second unbind
Signed-off-by: dinglongfei <dinglongfei@xiaomi.com>
1. support doublebuffer swtich for overlay layer
2. Add display area ioctl to scale the active area of the overlay layer
to a specific region on the LCD through hardware.
Signed-off-by: rongyichang <rongyichang@xiaomi.com>
Function gpio_lower_half_byname() was added to support registration of
GPIO pin by name as supported for IOexpander. Some of the code is wrapped
in new static function gpio_lower_half_internal() to avoid code
duplication.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
This adds support for 16 bit io expander pcf8575. The driver is basically
the same as for pcf8574 however it is for 16 bits instead of 8 bits. Since
pcf8575 and pcf8574 can be both used on the same i2c bus the driver for
pcf8575 is implemented in a different file to reduce the code size
and complexity and to have less if statements in the driver.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Some UART Controllers (Synopsys DesignWare 8250) will trigger spurious interrupts when the Line Control Register (LCR) is set while the UART is busy. This patch provides the option (16550_WAIT_LCR) to wait for UART until it's not busy, before setting the LCR. (16550_WAIT_LCR is disabled by default)
This patch fixes the spurious UART interrupts for the upcoming port of NuttX to StarFive JH7110 SoC (with Synopsys DesignWare 8250 UART). [The patch is explained here](https://lupyuen.github.io/articles/plic#appendix-fix-the-spurious-uart-interrupts)
drivers/serial/uart_16550.c: If 16550_WAIT_LCR is enabled, wait until UART is not busy before setting LCR
include/nuttx/serial/uart_16550.h: Define the UART Status Register (USR) for checking if UART is busy
drivers/serial/Kconfig-16550: Added option 16550_WAIT_LCR to 16550 UART Config, disabled by default
The fd of pipe type is not supported by mmap, mmap() shall failed
with ENODEV. If pipe mmap is not implemented, mmap will forward to
rammap() and get unexpected error.
Implement pipe mmap just return ENODEV. That is to pass LTP posix
test case mmap/23-1.c
https://pubs.opengroup.org/onlinepubs/9699919799/functions/mmap.html
Signed-off-by: fangxinyong <fangxinyong@xiaomi.com>
CC: note/note_driver.c note/note_driver.c:180:19: warning: 'g_note_lock' defined but not used [-Wunused-variable]
180 | static spinlock_t g_note_lock;
|
Comment for pcf8574_register_update() function was incorrect as it was
probably copied from different driver function.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
boards/arm/cxd56xx/drivers/sensors/bmi160_scu.c: fix incorrect comments to the Right of Statements.
drivers/sensors/ak09912.c: fix incorrect function description ak09912_putreg8 and ak09912_getreg8
W25QxxxJV NOR memories are backward compatible with older Winbond´s
generations and thus can also be supported here. This essentially brings
the support for generic SPI to W25QxxxJV memories as w25qxxxjv.c file only
supports QSPI communication.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
wdog_notifier() will be called in _assert to keep the crash scene
as mush as possible, which is useful for debug.
But once disable the watchdog, the hardware watchdog can not reboot
the system too. If a crash happened in the _assert (e.g. the tcb sp
has been corrupted, system will crash again in tack stack dump),
system will crashing forever and can not reboot.
So add a config to disable this feature by default and can be enable
if anyone need it.
Signed-off-by: Bowen Wang <wangbowen6@xiaomi.com>
When the value that is out of range is specified in ioctl(VIDIOC_S_CTRL) and
ioctl(VIDIOC_S_EXT_CTRLS), returned value should be not EINVAL but ERANGE.
video driver does not support flags member of ioctl(VIDIOC_QUERYCTRL)
and ioctl(VIDIOC_QUERY_EXT_CTRL).
But, ioctl returns with the flags member that has the garbage value.
Add initialization of flags member to avoid return of the garbage value.
drivers/sensors/bme680.c: The bme680 driver
sensor.h: Added new type of sensor (Gas) to be used for retrieving the bme680 data
esp32/common/src/esp32_bme680.c: bme680 support on esp32
esp32/esp32-sparrow_kit/esp32_bringup.c: added support for the bme680
esp32/esp32-sparrow-kit/configs/nsh/defconfig: fixed defconfig ci problem
Signed-off-by: simonatoaca <simona.alexandra2000@gmail.com>
esp32-sparrow-kit: Fixed defconfig
Signed-off-by: simonatoaca <simona.alexandra2000@gmail.com>
Code is now C89 compatible
Signed-off-by: simonatoaca <simona.alexandra2000@gmail.com>
Reused already defined sensor data structs by registering every sub-sensor separately
Signed-off-by: simonatoaca <simona.alexandra2000@gmail.com>
Implemented suggestions
Signed-off-by: simonatoaca <simona.alexandra2000@gmail.com>
1.support to use dd commond to burn romfs image to nand flash
2.support bare-write nand flash device without file system
Signed-off-by: dongjiuzhu1 <dongjiuzhu1@xiaomi.com>
Some hardware needs to config this delay to write one data block, because
the hardware needs more time to wear leveling and bad block manage.
Signed-off-by: dongjiuzhu1 <dongjiuzhu1@xiaomi.com>
The implementation of up_perf_*() is in a different static library in nuttx:
Hardware: libarch.a
Software: libdrivers.a (weak function)
Since functions with weak attributes cannot be correctly replaced in multiple static libraries,
this PR will use macros to replace whether the arch supports hardware perf events
Signed-off-by: chao an <anchao@xiaomi.com>
- considering simplicity and design assumption, the reset function must work without flaw.
If it fails, there is no way to recover but to reset again. so checking return status does not
bring additional benefit
- There is unnecessary switch inside switch which is making code not too readable
Signed-off-by: mks2183 <manishsharma3134@gmail.com>
nuttx/drivers/sensors/wtgahrs2.c: In function ‘wtgahrs2_initialize’:
nuttx/drivers/sensors/wtgahrs2.c:545:22: warning: ‘%lx’ directive output may be truncated writing between 1 and 16 bytes into a region of size 14 [-Wformat-truncation=]
545 | snprintf(arg1, 16, "0x%" PRIxPTR, (uintptr_t)rtdata);
| ^~~~~
nuttx/drivers/sensors/wtgahrs2.c:545:25: note: format string is defined here
545 | snprintf(arg1, 16, "0x%" PRIxPTR, (uintptr_t)rtdata);
nuttx/drivers/sensors/wtgahrs2.c:545:22: note: directive argument in the range [1, 18446744073709551615]
545 | snprintf(arg1, 16, "0x%" PRIxPTR, (uintptr_t)rtdata);
| ^~~~~
nuttx/drivers/sensors/wtgahrs2.c:545:3: note: ‘snprintf’ output between 4 and 19 bytes into a destination of size 16
545 | snprintf(arg1, 16, "0x%" PRIxPTR, (uintptr_t)rtdata);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: chao an <anchao@xiaomi.com>
3 wire interface for ST7789 LCD controller does not use CMD/DATA pin to
specify whether data or command is send but uses 9th bit of SPI transfer.
This commit adds support for 3 wire interface to ST7789 controller.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
use workqueue for rpmsgdev poll notify to prevent
calling rpmsgdev_poll_cb in interrupt context which
will try to hold mutex in rpmsg_send
Signed-off-by: liaoao <liaoao@xiaomi.com>
Remove TABs
Fix indentation
Fix Multi-line comments
Fix Comments to the Right of Statements.
Fix nuttx coding style
Fix Comments to the Right of Statements.
support to control the opening or closing of the specified channel through the syslogmask command at runtime
Signed-off-by: yinshengkai <yinshengkai@xiaomi.com>
usage:
1. Connect Jlink, start JLinkGDBServer
JLinkGDBServer -if SWD -device stm32h743zi -speed 16000
2. Listen to the RTT port data and forward it to the virtual serial port
sudo socat -d -d PTY,link=/dev/ttyRTT0,raw,ignoreeof TCP:127.0.0.1:19021,reuseaddr
3. Read serial data
minicom -D /dev/ttyRTT0
Performance:(STM32H743, 400MHZ)
time "dd if=/dev/zero of=/dev/console bs=512 count=2048"
6.67 sec 157KB/s
Signed-off-by: yinshengkai <yinshengkai@xiaomi.com>
Take the idea from Linux's iw_handler array and esp32c3_wlan's wlan_ops_s, and make it a common logic of upper-half driver.
Signed-off-by: Zhe Weng <wengzhe@xiaomi.com>
1. Update all CMakeLists.txt to adapt to new layout
2. Fix cmake build break
3. Update all new file license
4. Fully compatible with current compilation environment(use configure.sh or cmake as you choose)
------------------
How to test
From within nuttx/. Configure:
cmake -B build -DBOARD_CONFIG=sim/nsh -GNinja
cmake -B build -DBOARD_CONFIG=sim:nsh -GNinja
cmake -B build -DBOARD_CONFIG=sabre-6quad/smp -GNinja
cmake -B build -DBOARD_CONFIG=lm3s6965-ek/qemu-flat -GNinja
(or full path in custom board) :
cmake -B build -DBOARD_CONFIG=$PWD/boards/sim/sim/sim/configs/nsh -GNinja
This uses ninja generator (install with sudo apt install ninja-build). To build:
$ cmake --build build
menuconfig:
$ cmake --build build -t menuconfig
--------------------------
2. cmake/build: reformat the cmake style by cmake-format
https://github.com/cheshirekow/cmake_format
$ pip install cmakelang
$ for i in `find -name CMakeLists.txt`;do cmake-format $i -o $i;done
$ for i in `find -name *\.cmake`;do cmake-format $i -o $i;done
Co-authored-by: Matias N <matias@protobits.dev>
Signed-off-by: chao an <anchao@xiaomi.com>
There is no need to use global spinlock to protect netdev
specific data counters. Allocate per-netdev specific spinlock
to get better locking granularity.
Move C/C++ atomic support checking to compiler.h
Signed-off-by: Petro Karashchenko <petro.karashchenko@gmail.com>
LED effects must be implemented in the lower-half of the LED driver.
The interface is designed to supports the following LED effects:
- intenisty (PWM)
- Bling (Timer)
- Fade in, Fade out (Ramp)
In this nested loop, the iteration variable is the same for both loops.
This is a typo and the inner loop should use a new loop variable.
Signed-off-by: Mingjie Shen <shen497@purdue.edu>
Memory pointed by priv may be used (in line 1289) after it is
freed in line 1283.
Fix by adding the missing return statement in error handling.
Signed-off-by: Mingjie Shen <shen497@purdue.edu>
It is used to write the log message to the channel immediately
when the log message is generated in the interrupt context, which
is faster than the normal force callback.
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
syslog_force is used to force the syslog output to the
console in interrupt context, but we can use syslog_write
to do the same(and more) thing.
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Summary:
- In this implementation, only one descriptor is used for RX.
- NOTE: we still use two descriptors for TX
Impact:
- None
Testing:
- Tested with qemu-7.1
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
if number of bytes available for reading more than zero,set USRSOCK_EVENT_RECVFROM_AVAIL flag into the event
Signed-off-by: wangchen <wangchen41@xiaomi.com>
If the rptun driver set auto start, the smetx may has been used
in rptun_notify_wait() but not inited.
Signed-off-by: wangbowen6 <wangbowen6@xiaomi.com>
Directly return -ENOTTY in rpmsgxxx_ioctl() when the command is
not supported to avoid fdsan command FIOC_SETTAG and FIOC_GETTAG
pass to the rpmsg dev/mtd/blk server with CONFIG_FDSAN enabled.
Signed-off-by: wangbowen6 <wangbowen6@xiaomi.com>
