Otherwise we will try to dump the state of the current task, however the
exit handler has already started doing some cleanup and invalidated its
group. Accessing the group from dumponexit will crash.
Signed-off-by: Abdelatif Guettouche <abdelatif.guettouche@espressif.com>
"error: incompatible types when assigning to type 'struct filelist *' from type 'struct filelist'
filelist = tcb->group->tg_filelist;"
Signed-off-by: Abdelatif Guettouche <abdelatif.guettouche@espressif.com>
If source register of sw instruction is x0, we must point it to a constant zero
since in NuttX's context,
value of index 0 is EPC.
Signed-off-by: Huang Qi <huangqi3@xiaomi.com>
Hartid and cpuindex are not the same thing. Hartid is needed regardless
of SMP, for external interrupt handling etc.
SMP needs cpuindex which might not be index == hartid, so both are
needed. IMO it is clearer to provide separate API for both.
Currently the implementation of up_cpu_index is done a bit lazily,
because it assumes hartid == cpu index, but this is not 100% accurate,
so it is still missing some logic.
chip/c906_timerisr.c: In function 'up_timer_initialize':
Error: chip/c906_timerisr.c:71:3: error: implicit declaration of function 'DEBUGASSERT' [-Werror=implicit-function-declaration]
DEBUGASSERT(lower);
^~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: chao.an <anchao@xiaomi.com>
riscv_mhartid is no longer called by exception_common, so can remove
this file from platforms that don't need it.
Also fixes make warning:
Makefile:123: target 'riscv_cpuindex.o' given more than once in the same rule
IRQ_NSTACKS, ARCH_CPU_COUNT, CONFIG_SMP_NCPUS all relate to each
other. However, a bit of clean up can be done and everything can
be merged into SMP_NCPUS.
The MPFS bootloader case works also as it requires only 1 IRQ stack
for the hart that executes as bootloader.
Some risc-v based chips don't support unaligned data access,
it will trigger a exception and then lead to crash.
In this patch, we handle the misaligned access by software to make
system run continue.
Signed-off-by: Huang Qi <huangqi3@xiaomi.com>
ESP32C3 use customized irq encoding so it's hard to share further code
with other risc-v based chips, in this patch, we keep the exception
number definition with risc-v spec.
Signed-off-by: Huang Qi <huangqi3@xiaomi.com>
- Access to PLIC via S-mode registers
- Access to IRQs via S-mode registers / definitions
- Initialize S-mode registers upon boot
- Initialize per CPU area before nx_start
NOTE: S-mode requires a companion SW (SBI) which is not yet implemented,
thus S-mode is not usable as is, yet.
Remove riscv_fault since its code is duplicated with riscv_exception,
and there are textual excpetion reason in riscv_exception.
Signed-off-by: Huang Qi <huangqi3@xiaomi.com>
It might be useful to store things in memory per CPU. The tricky part
is that all CPUs run the same code and see the same memory, so some
kind of centralized access is required.
For now, the structure contains the hart id.
Access to the structure elements is provided via sscratch, which is
unique for every hart!
- Add config "ARCH_USE_S_MODE" which controls whether the kernel
runs in M-mode or S-mode
- Add more MSTATUS and most of the SSTATUS register definitions
- Add more MIP flags for interrupt delegation
- Add handling of interrupts from S-mode
- Add handling of FPU from S-mode
- Add new context handling functions that are not dependent on the trap
handlers / ecall
NOTE: S-mode requires a companion SW (SBI) which is not yet implemented,
thus S-mode is not usable as is, yet.
When process a is switched to process b, the address environment is
swapped with a call to group_addrenv(). The stack upon entry will be
a's, and upon exit b's. This will fail, so a neutral stack is required,
either a kernel stack or an IRQ stack.
Infrastructure for an IRQ stack is already in place, so give a hint
that an interrupt stack should be provided if address environments
are enabled.
