mount/fs_foreachmountpoint.c: In function 'mountpoint_filter':
mount/fs_foreachmountpoint.c:99:38: warning: 'sprintf' may write a terminating nul past the end of the destination [-Wformat-overflow=]
99 | sprintf(&dirpath[pathlen], "/%s", node->i_name);
| ^
In function 'mountpoint_filter',
inlined from 'mountpoint_filter' at mount/fs_foreachmountpoint.c:64:12:
mount/fs_foreachmountpoint.c:99:7: note: 'sprintf' output between 2 and 257 bytes into a destination of size 256
99 | sprintf(&dirpath[pathlen], "/%s", node->i_name);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: chao an <anchao@xiaomi.com>
since both aren't suitable after:
commit 98ab55ef68
Author: Xiang Xiao <xiaoxiang@xiaomi.com>
Date: Fri Dec 30 12:02:47 2022 +0800
drivers/note: Replace the scritical section with spin_xxx_wo_note
to avoid to generate the unexpected schedule information
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
since after the below commit, noteram driver can work even when
the instrumentation of csection, spinlock and smp is enabled
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
since the chip/board vendor could disable dirvers/note and
provide the implementation of sched_note_xxx by self
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
This reverts commit 62c15c03d3.
Fix warning: the choice symbol STM32_FLASH_CONFIG_G (defined at arch/arm/src/stm32/Kconfig:1275) is selected by the following symbols, but select/imply has no effect on choice symbols
- ARCH_CHIP_STM32F412ZG (defined at arch/arm/src/stm32/Kconfig:1014)
The original code hard-coded card detection to the low when card is
inserted and high when not. This might not be true on every board
because it depends on the slot and wiring used. The second reason is
because it is also possible to detect card with D3 pin pull-up when the
slot does not provide dedicated card detection switch.
This introduces new argument to the sam_hsmci_initialize to allow
invert of card detection pin. It also applies this invert to existing
boards as that was the state up to this point.
Generic drivers shoud not use architecture related config options like
CONFIG_SAMV7_PWM. This commit adds PWM pin overwrite under generic
configuration option CONFIG_PWM_OVERWRITE.
Now the overwrite can be used on other architectures as well or can be
completely disabled for SAMv7.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
This commit adds configuration file with enabled MCAN support. This is
mainly to track changes in architectural driver that could cause build
errors.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Commit d07792a caused a build error in sam_mcan.c file. This commit fixes
the build. The file now succesfully compiles and CAN works.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
POSIX dictates that assert() terminates via abort(), even though in NuttX
abort() just calls exit(EXIT_FAILURE) it is better to use the correct
API here, if at some point a proper implementation for abort() is made.
Also, as the kernel must not use abort() which is a userspace API, direct
the exit to PANIC() if for some reason _assert() returns (it should not
but trap it here just in case).
Remove calls to the userspace API exit() from the kernel. The problem
with doing such calls is that the exit functions are called with kernel
mode privileges which is a big security no-no.
Do not allow a deferred cancellation if the group is exiting, it is too
dangerous to allow the threads to execute any user space code after the
exit has started.
If the cancelled thread is not inside a cancellation point, just kill it
immediately via asynchronous cancellation. This will create far less
problems than allowing it to continue running user code.
For some reason the signal action was never performed if the receiveing
task was within a system call, the pending queue inser was simply missing.
This fixes the issue.
