Strongly-Ordered requires aligned access unless
caching is enabled.
Normal memory
Accesses to normal memory region are idempotent...
- unaligned accesses can be supported
With CONFIG_ARMV7M_DCACHE the cache maintenance operation
are not present. Or if CONFIG_ARMV7M_DCACHE_WRITETHROUGH
is on then buffering operations are no-ops.
This change enables MPU_RASR_C and MPU_RASR_B if
CONFIG_ARMV7M_DCACHE is only set.
if CONFIG_ARMV7M_DCACHE_WRITETHROUGH is set then only
MPU_RASR_C is enabled.
N.B When caching is disalbed unaligned access may cause hard faults
so add -mno-unaligned-access
It is always safe to enable Buffering in FLASH to achive unaligned
access leniency, as it is not written to.
the SDIO clock is not enabled when the bus goes to the idle state, that, in turn, breaks
IRQ delivering mechanism over DAT[1]/IRQ SDIO line to the host.
This reverts commit d9a5b92c1a306a70df52d50a02a80dc8ef20bf0d.
Revert "arch/arm: Remove -march and -mtune"
This reverts commit b8e99cf12f3a287311a2d341f285c71a5da3e4d4.
This commit adds new files that support functionality of QSPI driver in
SPI Master Mode. This functionality is included in new files sam_qspi_spi.x
to avoid too much mess in the source code. QSPI in SPI mode can be turn
on by config option SAMV7_QSPI_SPI_MODE.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
When NuttX is booted from a foreign (non NuttX)
bootloader. There as a possibility that the
bootloader configured the MPU, in an
incompatible way for the NuttX memory usage.
The option to reset the MPU before it is initialized
may not succeed if the bss and data initialization
code violated the previous MPU configurations.
Added herein are ARM_MPU_RESET and
ARM_MPU_EARLY_RESET. The former can be used
If the system is capable of booting and running
NuttX MPU configuration code without an MPU
violation. The latter is used if the system can
not run the bss and data initialization code.
These are options so that a NuttX may be configured to
not clobber a bootloader MPU configuration in a system
that is architected to share the MPU configuration task.
This commit adds header file imxrt_adc_etc.h for external ADC trigger
module. This contains only definitions of ADC_ETC registers and separate
bits, implementation of ADC_ETC driver is yet to be done.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
If we repeatedly call up_cpu_pause and up_cpu_resume, there would be
cases where the next call to up_cpu_pause happens while the other CPU is
still responding to the previous resume request. In this case the
DEBUGASSERT will trigger. We should allow the first CPU to wait until the
other CPU has finished responding to the resume request.
Signed-off-by: Abdelatif Guettouche <abdelatif.guettouche@espressif.com>
Gregory Nutt is the copyright holder for those files and he has submitted the
SGA as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Gregory Nutt has submitted the SGA
Omni Hoverboards has submitted the SGA
David Sidrane has submitted the ICLA
Mateusz Szafoni has submitted the ICLA
Sebastien Lorquet has submitted the ICLA
Paul Alexander Patience has submitted the ICLA
as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
The stm32_gpiosetevent calls stm32_configgpio. So
the pin is infact restored to the SDMMC/SDIO D0.
The seconday init, dropped interrupts in a debug
build with HW stack checking on after the GPIO glich
fixes and that was how it was detected.
This prevents gliches on changing to an output mode.
If not the ALT mux can be selecting a IP block that
is drving the line to say 0. Then the output is connected
to that source, then swithced to the correct source.
This prevents gliches on changing to an output mode.
If not the ALT mux can be selecting a IP block that
is drving the line to say 0. Then the output is connected
to that source, then swithced to the correct source.
This prevents gliches on changing to an output mode.
If not the ALT mux can be selecting a IP block that
is drving the line to say 0. Then the output is connected
to that source, then swithced to the correct source. This
produced a 430 nS glich on a F4 @168 Mhz. It was a enough
to corrupt an I2C device with a bus monitor.
Summary:
- This commit replaces the critical section with spinlock in cxd56_serial.c
Impact:
- None
Testing:
- Tested with spresense:rndis_smp, spresense:rndis
and spresense:rndis_wifi
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Gregory Nutt has submitted the SGA
Bill Gatliff has submitted the ICLA
as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Rearchitect video driver:
- Define two video I/F(struct imgsensor_ops_s and struct imgdata_ops_s),
and support them.
- CISIF driver supports new video I/F struct imgdata_ops_s.
- ISX012 driver supports new video I/F struct imgsensor_ops_s.
- Move ISX012 driver to general driver directory.
