This patch simplifies PMP handling for K230 using common APIs.
It also uses `g_misa` variable to expose the MISA issue.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
check if interrupt is busy when IRQCHAIN is disabled
this allows user to catch configuration errors and fail early when the
already busy vector is reused
Signed-off-by: p-szafonimateusz <p-szafonimateusz@xiaomi.com>
at default x86_64 supports SSE, SSE2, this commit adds support for
SSE3, SSSE3, SSE41, SSE42 and SSE4A
Signed-off-by: p-szafonimateusz <p-szafonimateusz@xiaomi.com>
this partly revert 4123615621 which works OK for PCI serial and network cards
but breaks QEMU EDU due to usage of sem and usleep in IDLE thread context.
Another solution will be provided later.
Signed-off-by: p-szafonimateusz <p-szafonimateusz@xiaomi.com>
Current NuttX SBI assumes empty PMP settings but that is not always
true, for example some bootloaders may have PMP entries locked before
handling over to NuttX. This patch revises it by not using hardcoded
PMP region number.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
Reproduce:
configure:
./tools/configure.sh qemu-armv7a:nsh -j8
open kasan:
CONFIG_MM_KASAN=y
run:
qemu-system-arm -cpu cortex-a7 -nographic -machine virt,virtualization=off,gic-version=2 -net none -chardev stdio,id=con,mux=on -serial chardev:con -mon chardev=con,mode=readline -kernel ./nuttx
error:
run hanged
Rootcause:
In Qemu armv7a, the ram-end reserved for MMU PGTABLE:
And the up_allocate_heap() directly use the ram-end for heap in arch/arm/src/common/arm_allocateheap.c
*heap_size = CONFIG_RAM_END - g_idle_topstack;
Then they are conflict.
Usually, we won't use the heap end, so can't find the error.
BUT, the KASAN will use the heap end for shadow, so found the error.
Resolve:
up_allocate_heap() consider of MMU, re-define the RAM_END at chip.h
Signed-off-by: ligd <liguiding1@xiaomi.com>
This commit adds support for TX DMA transfers for USART peripheral. Code
refactor in sam_serial.h was also required in order to have correct
defines for all possible cases (both RX and TX DMA used, just one used,
none used).
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
When an application is being loaded `up_addrenv_create ` calls
`create_region` to create the address environment. Only the first
entry is mapped when the region is created. Virtual memory that is
not mapped will trigger an exception when accessed. Other memory
pages are allocated and mapped on-demand. This enables setting
larger heap and stack for the process without compromising the
overall system memory.
Current `CONFIG_PAGING` refers to an experimental implementation
to enable embedded MCUs with some limited RAM space to execute
large programs from some non-random access media.
On-demand paging should be implemented for the kernel mode with
address environment implementation enabled.
Previously we need turn off the PMP locks in K230 vendor u-boot to use
NuttX, this complicates the setup process. This patch supports running
NuttX with original vendor u-boot so that to reduce setup complexity.
It also enables empty NSH prompt string in AMP master config as the apps
side support is ready.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
cpu0 thread0: cpu1:
sched_yield()
nxsched_set_priority()
nxsched_running_setpriority()
nxsched_reprioritize_rtr()
nxsched_add_readytorun()
up_cpu_pause()
IRQ enter
arm64_pause_handler()
enter_critical_section() begin
up_cpu_paused() pick thread0
arm64_restorestate() set thread0 tcb->xcp.regs to CURRENT_REGS
up_switch_context()
thread0 -> thread1
arm64_syscall()
case SYS_switch_context
change thread0 tcb->xcp.regs
restore_critical_section()
enter_critical_section() done
leave_critical_section()
IRQ leave with restore CURRENT_REGS
ERROR !!!
Reason:
As descript above, cpu0 swith task: thread0 -> thread1, and the
syscall() execute slowly, this time cpu1 pick thread0 to run at
up_cpu_paused(). Then cpu0 syscall execute, cpu1 IRQ leave error.
Resolve:
Move arm64_restorestate() after enter_critical_section() done
This is a continued fix with:
https://github.com/apache/nuttx/pull/6833
Signed-off-by: ligd <liguiding1@xiaomi.com>
Use private naming to avoid conflicts with user applications
In file included from libuv/src/unix/internal.h:25,
from libuv/src/unix/udp.c:23:
libuv/src/uv-common.h:57: warning: "container_of" redefined
57 | #define container_of(ptr, type, member) \
|
In file included from nuttx/include/nuttx/list.h:47,
from nuttx/include/nuttx/tls.h:40,
from nuttx/include/nuttx/sched.h:48,
from nuttx/include/nuttx/arch.h:87,
from nuttx/include/nuttx/userspace.h:35,
from nuttx/include/nuttx/mm/mm.h:30,
from nuttx/include/nuttx/kmalloc.h:34,
from nuttx/include/nuttx/lib/lib.h:31,
from nuttx/include/stdio.h:35,
from apps/system/libuv/libuv/include/uv.h:59,
from libuv/src/unix/udp.c:22:
nuttx/include/nuttx/nuttx.h:48: note: this is the location of the previous definition
48 | #define container_of(ptr, type, member) \
|
Signed-off-by: chao an <anchao@lixiang.com>
change optimization to -Os for CONFIG_DEBUG_FULLOPT to be compatible with other architectures
and add an option to select CONFIG_DEBUG_CUSTOMOPT
Signed-off-by: p-szafonimateusz <p-szafonimateusz@xiaomi.com>
