most licenses have been converted to Apache and the non Apache
licenses have been documented.
We can assume that now it should be the time to remove DISCLAIMER-WIP
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
RISC-V GCC is configured with --enable-initfini-array so it emits an
.init_array section instead of .ctors
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
This is required to avoid the interface header (syscall.h) depending on
the xtensa_swi.h header from the implementation
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
## Summary
`esp32c3_spi2_cmddata()` implements SPI Cmd/Data `SPI_CMDDATA()` for only 3 LCD drivers: ST7735, ST7789 and GC9A01.
This patch removes the check for LCD drivers, so that SPI Cmd/Data will work for all LCD drivers.
More details: https://github.com/apache/incubator-nuttx/pull/5898
## Impact
This change impacts LCD drivers that call `SPI_CMDDATA()`.
Previously `SPI_CMDDATA()` would fail with `ENODEV` for LCD drivers other than ST7735, ST7789 and GC9A01.
After patching, `SPI_CMDDATA()` will work correctly with all LCD drivers.
## Testing
This is a minor patch so no testing is needed.
## Summary
`bl602_spi_cmddata()` implements SPI Cmd/Data `SPI_CMDDATA()` for only 3 LCD drivers: ST7735, ST7789 and GC9A01.
This patch removes the check for LCD drivers, so that SPI Cmd/Data will work for all LCD drivers.
More details: https://github.com/apache/incubator-nuttx/pull/5898
## Impact
This change impacts LCD drivers that call `SPI_CMDDATA()`.
Previously `SPI_CMDDATA()` would fail with `ENODEV` for LCD drivers other than ST7735, ST7789 and GC9A01.
After patching, `SPI_CMDDATA()` will work correctly with all LCD drivers.
## Testing
We tested with LVGL and ST7789 on PineCone BL602:
- [Testing with LVGL](https://github.com/lupyuen/st7789-nuttx#run-lvgl-demo)
As for regular SPI Devices that don't require SPI Cmd/Data, we tested `CONFIG_SPI_CMDDATA=y` with Semtech SX1262 SPI Transceiver on PineCone BL602:
- [Testing Cmd/Data](https://github.com/lupyuen/incubator-nuttx/releases/tag/release-2022-03-30)
The SPSR is used to store the current value of the CPSR when an exception
is taken so that it can be restored after handling the exception.
Each exception handling mode can access its own SPSR.
User mode and System mode do not have an SPSR because they are not
exception handling modes.
Signed-off-by: chao.an <anchao@xiaomi.com>
## Summary
To control the Data/Command Pin on ST7789 SPI Display, the SPI Driver flips the MISO Pin as though it was a GPIO.
To implement this on BL602, we reconfigure MISO from SPI Pin to GPIO Pin on the fly inside `bl602_spi_cmddata()`.
When the SPI Port is deselected (after the SPI operation), we revert MISO back from GPIO Pin to SPI Pin. We implement this inside `bl602_spi_select()`.
[More Details Here](https://github.com/lupyuen/st7789-nuttx#spi-cmddata)
## Impact
This change impacts 3 LCD drivers that call `SPI_CMDDATA()`: ST7735, ST7789, GC9A01.
Previously the BL602 SPI Driver would fail with "SPI cmddata not supported" when the above drivers are used.
After the change, the above drivers will set the LCD Data/Command Pin correctly.
## Testing
We tested this implementation of SPI Cmd/Data with NuttX ST7789 Driver and a Logic Analyser on PineCone BL602:
- [Testing with Logic Analyser](https://github.com/lupyuen/st7789-nuttx#spi-cmddata)
We also tested LVGL with ST7789 on PineCone BL602:
- [Testing with LVGL](https://github.com/lupyuen/st7789-nuttx#run-lvgl-demo)
As for regular SPI Devices that don't require SPI Cmd/Data, we tested `CONFIG_SPI_CMDDATA=y` with Semtech SX1262 SPI Transceiver on PineCone BL602:
- [Testing Cmd/Data](https://github.com/lupyuen/incubator-nuttx/releases/tag/release-2022-03-29)
