since VNC server is very useful even without NX:
1.Replace nxgl_coord_t with fb_coord_t
2.Replace nxgl_rect_s with fb_area_s
3.Remove nxgl_xxx function call
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
This command enables the application to perform the final steps of the
booting process prior to finally switching the execution to another
firmware image.
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
BOARDIOC_SWITCH_BOOT is required to communicate the boot partition from
userspace (OTA subsystem) to board. It can be used to change the system
boot behavior. So it's useful for A/B boot or even single boot case.
For the board support A/B boot case:
1. Download the new image from the sever
2. Write the new image to the alternative partition
3. Call BOARDCTL_SWITCH_BOOT to the alternative system
For single boot partition case:
1. Download the new image from the sever
2. Call BOARDCTL_SWITCH_BOOT and reboot to a small system
3. Write the new image to the main partition in the small system
4. Call BOARDCTL_SWITCH_BOOT again to the main system
Change-Id: Ifebb495784ecf06842946a249bec64f75dce894f
Signed-off-by: liuhaitao <liuhaitao@xiaomi.com>
We already have a debug assert and a return error this warning
will fail builds that are not even using this ioctl.
Signed-off-by: Brennan Ashton <bashton@brennanashton.com>
board/boarctl.c: Add support for the new BOARDIOC_ROMDISK command. This allows applications to create ROMFS block drivers without illegal direct calls to romdisk_register.
include/sys/boardctl.h: Add basic definitions to support a ROM disk creation boardctl() command.
Squashed commit of the following:
drivers/: Run tools/nxstyle against all drivers/*.c.
boards/boardctl.c: Add new boardctl() command, BOARDIOC_MKRD, that can be used to create a RAM disk. This will replace the illegal call to ramdisk_register() currently used by NSH.
drivers/mkrd.c: Add wrapper around ramdisk_register() for creating a proper ramdisk.
Move boards to boards folder
* boards: rename configs folder to boards
This is the proposed layout after the change:
boards: - folder containing board folders
<board>: - name of each board
drivers: - extra drivers specific for platform
include: - header files for the boars
scripts: - extra scripts specific for platform
src: - board specific code
tools: - extra tools specific for platform
<config>: - board specific configuration(s)
Note:
<xxx> names are dependent on platform
This is a logical change to aim to the arch layout but this is a
huge change it should be done in several steps to lower the risk.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Kconfig: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Makefile: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Makefile.*: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Make.defs: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .sh: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .mk: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .c & .h: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .bat: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
