arch/arm/src/s32k1xx/s32k1xx_lowputc.c: Fix a typo that prevented LPUART1 from working.
arch/arm/src/s32k1xx/s32k1xx_periphclocks.c and related files: Fix yet another case of confusion between pre-decremented and non-decremented divider values. Enforce the rule that dividers are not decremented until the moment they are written into registers.
arch/arm/src/s32k1xx/s32k1xx_clockconfig.c: Fix another problem related to whether a divider is pre-decremented or not. The answer must be the divder values are never pre-decremented. They are decremented just before being written to hardware.
arch/arm/src/s32k1xx/s32k1xx_clockconfig.c: Clean up some bad conditional logic. Precedence of operators problem.
boards/arm/s32k1xx/s32k118evb: Add support for execution out of SRAM. This is helpful for bringup when you want to avoid putting a lethal image in FLASH.
arch/arm/src/s32k1xx/s32k1xx_clockconfig.h: Remove crystal frequency, it is not used.
arch/arm/src/s32k1xx/s32k1xx_wdog.h: Fix a typo in a register name.i
boards/arm/s32k1xx/s32k*evb/configs/nsh/defconfig: Create Motorola SREC output format.
boards/arm/s32k1xx/s32k118evb/include/board.h: Add LPUART0 pin disambiguation.
arch/arm/src/s32k1xx/hardware: Add pin mux definitions for S32K116, 118, 142, 144, 146, and 148.
arch/arm/src/s32k1xx/s32k1xx_pin.c and .h: Add support for PIDR register that disables a gneral purpose pin from acting as an input.
arch/arm/src/s32k1xx/s32k1xx_pin.c and .h: The device does not support slew rate controls or open drain (on all the pins). Only pins that are configured for a protocol that requires open-drain (e.g;, LPI2C, LPUART single-wire) will work in open-drain mode.
arch/arm/src/s32k1xx/: Add logic to look up the peripheral clock frequency. Fix baud calcuation logic in s32k1xx_lowputc.c: In no longer tries to enable clocking. That must be done with board logic. Now gets the peripheral functional clock frequency to determine the baud rate.
arch/arm/src/s32k1xx: Add peripheral feature arrays.
Finishes peripheral clock initialization:
arch/arm/src/s32k1xx/s32k11x/s32k11x_clockmapping.c
arch/arm/src/s32k1xx/s32k14x/s32k14x_clockmapping.c
Provide MCU-specific mapping of clock names to PCC control registers.
boards/arm/s32k1xx/s32k118evb/src/s32k118_periphclocks.c
Provides initial clocking for for the S32K118EVB
arch/arm/src/s32k1xx/s32k1xx_periphclocks.c: Add logic to initialize peripheral clocking.
arch/arm/src/s32k1xx/s32k1xx_clockconfig.c: Add SIM clock configuration.
stm32h7 RTC and friends support
* stm32h7:Removed f7 in file path
* stm32f7:Fix overwritten IRQ enabled
System boot order calls clock_initialize then up_initalize.
clock_initialize was setting up the alarm IRQ
up_initalize is initializing the NVIC.
This most likely worked in the past due to a bug in the
NVIC init code that failed to clear the Interrupt enables.
That was fixed in 510b0f7e arch/arm/src: Correct all ARMv7-M
architectures. Interrupts were not be disabled correctly
on power up.
* stm32h7:Ported over F7 RTC
* nucleo-h743zi:Add RTC
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arch/arm/src/s32k1xx/s32k1xx_clockconfig.c: Finishes the implementation of the core clock configuration logic.
arch/arm/src/s32k1xx/hardware/s32k1xx_smc.h: Add SMC register definition header file.
arch/arm/src/s32k1xx: Bring in GPIO logic from Kinetis. Looks like the same IP.
serial single-wire: add possibility to specify pull-up instead of open drain
Approved-by: David Sidrane <david.sidrane@nscdg.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
