1. For buffered tcp/udp case, if CONFIG_NET_ARP_SEND/CONFIG_NET_ARP_IPIN/CONFIG_NET_ICMPv6_NEIGHBOR isn't enabled and the table doesn't contain ip<->ethaddr mapping yet, the logic will skip the realtransmission and then arp/neighbor can't steal the final buffer to generate arp/icmpv6 packet.
2.for all other case, the tcp layer or user program should already contain the retransmit logic, the check is redundancy and may generate many duplicated packets if arp/icmpv6 response is too slow because the cursor stop forward. If user still concern about the very first packet lost, he could fix the issue by enabling CONFIG_NET_ARP_SEND/CONFIG_NET_ICMPv6_NEIGHBOR at begin.
drivers/ieee802154/xbee: Add configuration option for setting the default prefix to use when bringing up the network and setting the IP address.
# Conflicts:
# drivers/wireless/ieee802154/xbee/xbee_netdev.c
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Iobinstrumentation
* mm/iob: Introduces producer/consumer id to every iob call. This is so that the calls can be instrumented to monitor the IOB resources.
* iob instrumentation - Merges producer/consumer enumeration for simpler IOB user.
* fs/procfs: Starts adding support for /proc/iobinfo
* fs/procfs: Finishes first pass of simple IOB user stastics and /proc/iobinfo entry
Approved-by: Gregory Nutt <gnutt@nuttx.org>
ieee802154/sixlowpan: Removes unnecessary conversions that were happening due to a misunderstanding of byte ordering with EUI-64
# Conflicts:
# drivers/wireless/ieee802154/xbee/xbee_netdev.c
Approved-by: Gregory Nutt <gnutt@nuttx.org>
net/ipforward: Check if interface is up early on when forwarding to avoid extra work.
As noticed in a previous wireless commit, when forwarding is enabled and a packet comes in, the packet is attempted to be sent on each other netdev without regard for whether it is in the UP state. Of course this is eventually caught, but it can be caught earlier to avoid unnecessary work, especially in the 6LoWPAN case where a useless packet conversion will occur.
Approved-by: Gregory Nutt <gnutt@nuttx.org>
net/udp: Remove net stack dependency from CONFIG_NET_BROADCAST
This change allows us to use CONFIG_NET_BROADCAST without network
stack. (i.e. usrsock application can use broadcast)
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Squashed commit of the following:
net/: Fix some naming inconsistencies, Fix final compilation issies.
net/inet/inet_close(): Now that we have logic to drain the buffered TX data, we can implement a proper lingering close.
net/inet,tcp,udp: Add functions to wait for write buffers to drain.
net/udp: Add support for notification when the UDP write buffer becomes empty.
net/tcp: Add support for notification when the TCP write buffer becomes empty.
net/inet: Fix tcp active close in inet_close.c
In previous implementation, FIN packet was not sent when a socket
is actively closed (e.g. telnetd or webserver) without SO_LINGER.
This issue happens because the socket closing sequence waits for
the status.cl_sem only if lingering timeout is set. However,
in many server use-cases, SO_LINGER is not usually set and even
in these cases, FIN packet must be sent correctly.
This PR changes the logic in inet_close.c so that it can wait
for status.cl_sem regardless of SO_LINGER. Instead, if SO_LINGER
is set, it waits for the semaphore with timeout option.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
net/usrsock: Fix debug logs and remove DEBUGASSERT from usrsockdev_do_request()
In a client mode, socket() will be the first request for usrsockdev_do_request().
However, in a server mode, the first request to accepted sockets will be recv()
or others which depend on applications. So I think we should remove this
DEBUGASSERT from usrsockdev_do_request().
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
ez80: Fixing a few more compile problems. I am afraid that the 5.3.0 compiler it too buggy to use.
ez80: Additional build-related fixed.
eZ80: Updating to use the newest ZDSII 5.3.0 toolchain.
arch/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
sched/ audio/ crypto/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
Documentation/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
fs/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
graphics/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
net/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
drivers/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
include/, syscall/, wireless/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
configs/: Remove all references to CONFIG_DISABLE_POLL. Standard POSIX poll can no longer be disabled.
