This conversion is unfortunate in the sense that Unix local domain sockets are relatively lightweight. LocalHost UDP sockets are much heavier weight since they rely on the full UDP stack. If anyone is up for a complete redesign, then using some shared memory and a POSIX message queue would be lightweight again.
This commit also fixes several bugs that were not testable before the inode tree deadlock. I cannot say that the logic is 100% stable but it does not have basic functionality.
Squashed commit of the following:
fs/userfs: Order locking so that access to the shared I/O buffer is also locked.
fs/userfs: Converts to use LocalHost UDP loopback for IPC.
According to the specification, the close function must wait until all data
has been written before it closes the file (except O_NONBLOCK is set). The
maximum waiting time for this is not specified.
To be able to edit the file list of the process, the close function has to lock
the file list semaphore. After that the close function of the serial driver is
called.
Waiting for the complete transmission of all data is done in the serial driver.
This causes the semaphore to remain locked until all data has been sent.
However, no other thread of the process can edit the file list for that time
(open, close, dup2, etc.). This is not optimal in a multithreaded environment.
Therefore, we have to keep the waiting time within the driver as short as possible.
ieee802154: Simplifies notify() and rxframe() calls to a single notify() call. dataind's and all other "notifs" are now "primitives" which aligns with standard terminology
* mac802154: Adds missing breaks from case statement
* sixlowpan: Fixes bad logic where ACK is not requested if address is not a broadcast
* ieee802154: Simplification of "notifs" and "datainds" to generic primitives passed via a single notify call to the layer above the MAC
* Directories.mk should reference CONFIG_WIRELESS instead of CONFIG_DRIVERS_WIRELESS
* xbee_netdev: Network must be locked when calling sixlowpan_input
* sixlowpan: Reassembly buffer can't be freed if provided by radio driver
* sixlowpan: Don't free IOB if there is an error processing it as the MAC will try to pass it along to another receiver
* ieee802154: Adds basic logging to ieee802154_primitive.c
* Minor fixes after rebase
* xbee: Adds AT query timeout to retry if XBee doesn't respond to request
* same70-xplained: Adds Xbee support. Makes mikroBus slot Kconfig 'choice'
* mac802154: Removes unused function declaration
* drivers/mrf24j40: Fixes compilation error using . operator rather than -> operator
* mac802154_device: Changes a few mac802154_primtive_free's to ieee802154_primitive_free() and changes notif to primitive in a couple places.
* mac802154: Adds promiscous mode logic to bypass parsing of incoming frames. MAC char device also checks for promiscous mode and passes whole frames including header and FCS to the application if promiscous mode is enabled.
* sixlowpan: Fixes logic to correctly check if packet is large enough to include header. This would cause packets to be considered too small when they are sufficiently sized.
* sixlowpan: Fixes forwarding logic to use forwarding device rather than received device to look up destination link layer address
* net/ipforward: Fixes typo that caused build error when IP forwarding was enabled with CONFIG_NET_ICMPv6_NEIGHBOR enabled as well.
* configs/same70-xplained: Simple spelling fix
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Fix GPIO operation of STMPE811 driver.
Fixed issues:
1. STMPE811_GPIO_DIR was defined for register name
and later was redefined to be the pin direction mask
for `stmpe811_gpioconfig`
I decided to change register name to be STMPE811_GPIO_DIR_REG,
and keep pin direction mask STMPE811_GPIO_DIR, so that any
external code that already use this driver will be unchanged.
2. The STMPE811 register GPIO_DIR uses bit value 1 for output
and 0 for input, but `stmpe811_gpioconfig` set the opposite.
3. The call to `stmpe811_gpiowrite` from inside of `stmpe811_gpioconfig`
leaded to deadlock.
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Squashed commit of the following:
net/icmpv6: IPPROT_ICMP6 socket logic now builds without error.
net/icmpv6: Add support for read-ahead and poll(). Initial commit is just cloned from ICMP with the appropriate name changes.
configs/: All defconfig filess that include CONFIG_NET_ICMPv6_SOCKET=y need to select CONFIG_SYSTEM_PING6=y and deselect CONFIG_DISABLE_POLL.
Update NSH documention to show that ping6 is now a built in command.
net/icmpv6: Add icmpv6_sendto.c and icmpv6_recvfrom.c. Initial versions are just clones from icmp/ with appropriate name changes.
net/icmpv6: Clone some ICMP socket logic as the beginning of support for ICMPv6 socket support.
Rename CONFIG_NET_ICMPv6_PING to CONFIG_NET_ICMPv6_SOCKET. Move prototype for icmpv6_ping from include/nuttx/net/icmpv6 to net/icmpv6/icmpv6.h
STM32L1, STM32L4 RTC: add periodic interrupts, update L1 RTC implementation
* STM32L4 RTC: add support experimental CONFIG_RTC_PERIODIC
* STM32 RTC: separate STM32L1 RTC into a separate file
STM32L1 RTC is very close to F4 or L4 versions, with two alarms
and periodic wakeup support so backported L4 peripheral to L1.
* RTC: add periodic alarms to upper and lower halves
Approved-by: Gregory Nutt <gnutt@nuttx.org>
The same interrupt handler is entered with the device structure parameter in all situations,
multiple or single PCA. One should still be careful if multiple PCA devices share the same IRQ.
Stm32 rtc small patches
* RTC: canceling an alarm marks it as inactive
* STM32L4, STM32F4, STM32F7 RTC: fix reading alarm value that is more than 24h in future
* STM32F0 RTC: fix backup register count in stm32_rtcc.h
All other STM32: SHIFTR_SUBFS_MASK was correct in STM32F0 only
* STM32L1: use correct EXTI line definitions
Approved-by: Gregory Nutt <gnutt@nuttx.org>
This commit adds a driver for this chip. Right now it measures bus voltage and current, and does not use the internal calibrated current reading, nor the available power measurement.
Change all calls to mq_receive() and mq_timedreceive() in the OS to calls to nxmq_receive() and nxmq_timedreceive(), making appropriate changes for differences in return values.
sched/mqueue: Add nxmq_receive() and mxmq_timedreceive() which are functionally equivalent to the standard mq_receive and mq_timedreceive() except that (1) they do not create cancellation points, and (2) the do not modify the application's errno variable.
Change all calls to mq_send() and mq_timedsend() in the OS to calls to nxmq_send() and nxmq_timedsend(), making appropriate changes for differences in return values.
sched/mqueue: Add internal function nxmq_send() and nxmq_timedsend() that are equivalent to mq_send() and mq_timedsend() except that they do not create cancellation points and do to not modify the errno variable.
