Load all sections to LMA not VMA, so the startup code(e.g. start.S) need
relocate .data section to the final address(VMA) and zero .bss section by self.
For example, SiFli and Actions: Background: Device with small sram,
Bootloader run in sram and psram, need boot to Application, with memory overlap
and without XIP. VMA of .data is in "psram" and LMA in "rom", if not enable
`ELF_LOADTO_LMA`, ELF loader will load the section to VMA (will fill bootloader
itself).
Signed-off-by: wangjianyu3 <wangjianyu3@xiaomi.com>
xres and yres of video overlay buffer may not same as primay framebuffer.
so add it to check the framebuffer count of overlay
Signed-off-by: rongyichang <rongyichang@xiaomi.com>
This commit adds basic support for electrically isolated 8 bit expander.
The expander communicates with the MCU via SPI interface. Both single
and multiple pin read are supported.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
This commit adds support for galvanic isolated ISO1H812G SPI expander.
Both single pin and multiple pin writes are supported.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Move SCU-specific ak09912 sensor into spresense board layer.
Rename a function name to register SCU sensor driver
from ak09912_register to ak09912_scu_register.
Channel polarity can now be set with PWMIOC_SETCHARACTERISTICS ioctl
command as field cpol was added to pwm_info_s structure. This way the
polarity can be easily set from application layer for each channel
apart and also can be change on at runtime if required (although this is
not likely).
Helper defines were also added to simplify the definition of low and high
polarity level. Architecture level should take care of writing the
polarity to correct MCU registers.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Allows the debug behavior to be specified as part of the board, architecture or chip configuration. This is useful when using out-of tree custom board configurations.
Documentation for PWMIOC_SETCHARACTERISTICS ioctl command mentioned
that this command will neither start nor stop the pulsed output. This
however is incorrect as PWMIOC_SETCHARACTERISTICS command leads to
pwm_start() function which starts the pulsed output.
While this might not be the correct behaviour (I would probably welcome
the option to set PWM characteristics without starting the pulsed output)
it is the way the PWM driver is coded for many architectures. Future
enhancement might be to add function pwm_setchar() for example to just
set characteristics without starting the PWM output.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Some driver like virtio-net can offload fragmented IOBs, so an interface
to support this feature is needed.
Signed-off-by: Zhe Weng <wengzhe@xiaomi.com>
- Fix `ip6_map_ipv4addr` and `ip6_get_ipv4addr` macro to work under
different endianness.
- Use `iob_reserve` instead of `iob_trimhead` in `udp_datahandler`.
- Because we may set `sockaddr_in6` into IPv4 header, which causes
`offset` become negative. `iob_reserve` can hold this case while
`iob_trimhead` cannot.
- Select IPv4 domain in send case.
Signed-off-by: Zhe Weng <wengzhe@xiaomi.com>
Implement I_SUID/I_SGID feature for binfs in the POSIX compliant way.
If set-user-ID bit is set in the file permissions, then the effective
user ID of process shall be set to UID of the new process image file.
test case:
hello example emulates to set uid and file set-user-ID bit, and call
geteuid and getegid API.
UID = 2000
GID = 3000
MODE = 06555
nsh> ls -l /bin/hello
-r-sr-sr-x 2000 3000 0 hello
nsh> hello
geteuid:2000
getegid:3000
Signed-off-by: fangxinyong <fangxinyong@xiaomi.com>
From posix spec, if set-user-ID bit is set in the file permissions,
then the effective user ID of the new process shall be set to the
user ID of the new process image file.
Let's ignore whether ST_NOSUID is set on the mounted file system.
https://pubs.opengroup.org/onlinepubs/007904875/functions/exec.html
test step:
hello example build as a module and call geteuid and getegid API.
then set file binary set-user-ID bit on the host.
$ chmod +s apps/bin/hello
nsh> mount -t hostfs -o fs=. /data
nsh> ls -l /data/apps/bin/hello
-rwsrwsr-x 1000 1000 9264 /data/apps/bin/hello
nsh> /data/apps/bin/hello
geteuid:1000
getegid:1000
Signed-off-by: fangxinyong <fangxinyong@xiaomi.com>