Gregory Nutt
2043e1a114
IOBs: Move from driver/iob to a better location in mm/iob
2017-05-09 07:35:30 -06:00
Gregory Nutt
d5207efb5a
Be consistent... Use Name: consistent in function headers vs Function:
2017-04-21 16:33:14 -06:00
Gregory Nutt
bcc6b61fc1
Move include/nuttx/net/iob.h to include/drivers/iob.h; rename CONFIG_NET_IOB to CONFIG_DRIVERS_IOB
2017-04-20 14:53:30 -06:00
Gregory Nutt
64933246c3
6loWPAN: Tie 6loWPAN send into common socket send logic.
2017-03-28 14:08:54 -06:00
Gregory Nutt
9f7d332028
Minor changes from the review of the last PR
2017-01-18 07:32:27 -06:00
Pascal Speck
2e074ca4f9
- Fixed some issues that prevented ipv6 to work with ipv4 enabled.
2017-01-18 10:57:15 +01:00
Gregory Nutt
7467329a98
Eliminate CONFIG_NO_NOINTS. Lots of files changed -> lots of testing needed.
2016-12-03 16:28:19 -06:00
Gregory Nutt
d40a473f72
Without lowsyslog() *llwarn() is not useful. Eliminate and replace with *warn().
2016-06-20 09:37:08 -06:00
Jakub Łągwa
338b915008
While working with version 7.10 I discovered a problem in TCP stack that could be observed on high network load. Generally speaking, the problem is that RST flag is set in unnecessary case, in which between loss of some TCP packet and its proper retransmission, another packets had been successfully sent. The scenario is as follows: NuttX did not receive ACK for some sent packet, so it has been probably lost somewhere. But before its retransmission starts, NuttX is correctly issuing next TCP packets, with sequence numbers increasing properly. When the retransmission of previously lost packet finally succeeds, tcp_input receives the accumulated ACK value, which acknowledges also the packets sent in the meantime (i.e. between unsuccessful sending of lost packet and its proper retransmission). However, variable unackseq is still set to conn->isn + conn->sent, which is truth only if no further packets transmission occurred in the meantime. Because of incorrect (in such specific case) unackseq value, few lines further condition if (ackseq <= unackseq)is not met, and, as a result, we are going to reset label.
2016-06-20 06:55:29 -06:00
Gregory Nutt
7d0950bb22
net/: Change some nerr() ERRORS to nwarn() WARNINGS. Anomolous network events are not errors.
2016-06-12 07:09:37 -06:00
Gregory Nutt
f4fcdcdb4d
net/: Change some *err() message to *info() messages if what was a *dbg() message does not indicate and error condition.
2016-06-11 17:37:21 -06:00
Gregory Nutt
a1469a3e95
Add CONFIG_DEBUG_ERROR. Change names of *dbg() * *err()
2016-06-11 15:50:49 -06:00
Gregory Nutt
e99301d7c2
Rename *lldbg to *llerr
2016-06-11 14:55:27 -06:00
Gregory Nutt
86b79b33cf
Reserver the name 'err' for other purposes
2016-06-11 14:40:07 -06:00
Gregory Nutt
1cdc746726
Rename CONFIG_DEBUG to CONFIG_DEBUG_FEATURES
2016-06-11 14:14:08 -06:00
Gregory Nutt
fc3540cffe
Replace all occurrences of vdbg with vinfo
2016-06-11 11:59:51 -06:00
Gregory Nutt
4639cdd894
TCP timeouts: Fix some logic when there are multiple network interfaces. In this case, TCP timeout events can really only being processed when the poll from the correct device is received.
2016-03-20 08:19:00 -06:00
Gregory Nutt
2c95fef501
Remove some empty code section comments
2016-02-26 07:35:55 -06:00
Gregory Nutt
8db55f6493
Back out most of previous commit
2016-02-26 06:45:37 -06:00
Gregory Nutt
0b441ff1f4
net/: Add basic IEEE 802.15-4 socket support
2016-02-25 14:01:22 -06:00
Andrew Webster
49e5cc5a6f
TCP: check for an active connection before cleaning it up
...
If there is no active connection (e.g. it is waiting in accept), then
the connection object, which doesn't yet exist, should not be cleaned
up when the socket is closed.
2016-01-22 16:22:09 -06:00
Andrew Webster
5e3023bef1
TCP: return from write when there is no buffer space
...
During a write, if there is no more buffer space for the user data,
return the amount that was written instead of waiting until there
is free space. If nothing has been written yet, then block as before.
This solves a deadlock that occurs if the user data is too large to
fit in the available buffer: the write thread will block before any
data is added to the write queue, leaving no possibility that more
buffers will free up when they are ACKed (since they have not yet been
sent). The write thread will then block forever and hold all of the
buffers.
2016-01-22 16:19:20 -06:00
Andrew Webster
cdd187a7f3
TCP: check for sndcb before using it
2016-01-22 15:54:45 -06:00
Andrew Webster
df211ee46a
TCP: add writable check during poll
...
When a poll requesting POLLOUT happens, the poll should return
immediately if a write will not block. This change adds that, as
opposed to the old behaviour of blocking until a timer from the
Ethernet driver eventually triggers the poll to complete.
This is only implemented for buffered TCP. Unbuffered TCP should
behave as before.
2016-01-22 15:52:14 -06:00
Andrew Webster
99f5fcda70
iTCP: use lowlevel syslog to avoid infinte recursion
...
If stdout is a socket (e.g. telnet), then the debug message will cause
more TCP data to be sent, which generates another message, and so on
2016-01-22 15:41:48 -06:00
Gregory Nutt
6209c51206
net/: More clean-up of spacing/alignment issues
2015-10-08 15:10:04 -06:00
Gregory Nutt
0b12dbf95d
Fix some spacing problems
2015-10-04 15:04:00 -06:00
Gregory Nutt
b1e09d4847
net/socket and net/tcp: Fix a problem in whent there are multiple network devices. Polls were being sent to all TCP sockets before. This is not good because it means that packets may sometimes be sent out on the wrong device. That is inefficient because it will cause retransmissions and bad performance. But, worse, when one of the devices is not Ethernet, it will have a different MSS and, as a result, incorrect data transfers can cause crashes. The fix is to lock into a single device once the MSS is locked locked down.
2015-08-27 09:06:46 -06:00
Gregory Nutt
3bcdb218ff
Networking: Get rid of the tcp_mss macro. It is confusing and only obfuscates what is really going on
2015-08-27 08:39:17 -06:00
Gregory Nutt
6687e156e6
Revamp last change. IFF_UP only required when allocating callback, not freeing.
2015-05-30 21:13:58 -06:00
Gregory Nutt
04a661a97c
TCP networking: Add support for network driver events
2015-05-30 09:12:27 -06:00
Gregory Nutt
b756df982d
net/: Lots of build problems introduced into multiple NIC support. Many places where conditional logic based on CONFIG_NETDEV_MULTINIC is confused with CONFIG_NET_MULTILINK. Lots of code changed with IPv6 that was never compiled with MULTINIC enabled. Still some problem with parameter passing.
2015-02-09 18:15:34 -06:00
Gregory Nutt
a07a764d42
ICMPv6: Adds basic logic to support verification that we have the IPv6 address in the Neighbor Table. This feature is important because otherwise the first packet sent to a remote peer will fail (it will be replaced with a Neighbor Solicitation).
2015-02-02 13:44:31 -06:00
Gregory Nutt
ccc72edc0b
Networking: Add UDP read-ahead support and support for poll/select on UDP sockets. From Macs N.
2015-01-30 06:08:26 -06:00
Gregory Nutt
371a9fd84c
Networking: Fix another deadlock condition. tcp_write_buffer_alloc() calls sem_wait() with network locked. That worked if CONFIG_NET_NOINTS was not defined because interrupts are automatically restored when the wait happens. But with CONFIG_NET_NOINTS=y, the wait blocks with the network locked -- bad style and also can lead to a deadlock condition
2015-01-28 11:56:11 -06:00
Gregory Nutt
c77426e550
Cosmetic changes to comments; refresh configuration
2015-01-22 14:46:36 -06:00
Gregory Nutt
46fc574f0f
Forgot to remove some debug instrumentation in the last commit
2015-01-22 10:35:11 -06:00
Gregory Nutt
7106469191
Armv7-M: Remove Px4-only setting of stack to 0xff. This is incompatible with standard NuttX stack montitoring logic
2015-01-22 10:09:10 -06:00
Gregory Nutt
eb3c6e8390
Networking: Some fixes for compilation when both IPv4 and IPv6 are enabled
2015-01-18 09:23:22 -06:00
Gregory Nutt
f7663ef0ab
Networking: Final detangle off IPv4 and IPv6 TCP/UDP send logic. The Networking subsystem now compiles with IPv6 enabled
2015-01-18 08:56:05 -06:00
Gregory Nutt
820509eadc
Networking: Fix accept() so that it returns the correct IP address for the selected socket IP domain.
2015-01-17 09:27:05 -06:00
Gregory Nutt
4ad5998db3
net/socket and net/tcp: When we are ready to receive data or when we have outgoing data ready to be sent, we need to the notify the appropriate device driver of this condition. The notifying socket will be configured as either PF_INET or PF_INET6 and must look up the correct driver using the correct IP domain.
2015-01-17 08:33:14 -06:00
Gregory Nutt
2c251d845c
include/net/if.h: Add a bit to the device flags to indicate if the device packet buffer holds an IPv4 or an IPv6 domain packet. Set/clear the flag along with the correct offset to the application payload data as each packet is received.
...
net/socket, net/tcp, net/udp: Add logic to select the domain of the outputgoing packet before sending any UDP or TCP packet. This sets the bit to indicate the IPv4 or IPv6 domain and the correct offset to the output going payload data.
2015-01-17 07:42:09 -06:00
Gregory Nutt
5e938941a6
Networking: Replace all references to net_ipaddr_t with either in_addr_t on net_ipv6addr_t. The goal is to support both IPv4 and IPv6 simultaneously. This requires that the two types be distinct and not conditionally typedef'ed to net_ipaddr_t.
2015-01-16 12:30:18 -06:00
Gregory Nutt
bee89be4f4
Networking: Drivers can have both IPv4 and IPv6 addesses, but a socket can only only one or the other; The socket connnection structures need to include a union of IPv4 and IPv6 addresses for the local address binding and for the remote address connections
2015-01-16 10:01:54 -06:00
Gregory Nutt
60e50ff3b5
Networking: More IPv6 detanglement
2015-01-15 13:08:28 -06:00
Gregory Nutt
b36dbe1d89
Add logic to netdev_findbyaddr() to return the correct network device for the case where a broadcast address is used. This change caused trivial ripples through other files because additional parameters are required for netdev_findbyaddr() when CONFIG_NET_MULTINIC
2014-11-23 11:00:22 -06:00
Gregory Nutt
2e55db369d
Network: All logic will now handle varialbe length link layer protocol headers within incoming packets. This permits use of multiple network interfaces with differing data links. For example, ETHERNET + SLIP
2014-11-15 13:13:23 -06:00
Gregory Nutt
6e04518e4a
If CONFIG_NET_ARP_SEND is enabled, then all ICMP, TCP, and UDP send operations will call arp_send() before attempting the real send operation. arp_send() will check if the the IP address mapping is in the ARP table and, if not send ARP requests periodically until it is. This eliminates losing the first outgoing message because there is not mapping in the ARP table.
2014-08-18 16:22:14 -06:00
Gregory Nutt
73f3ecf7e2
NET: Rename network interrupt event flags more appropriately: TCP_, UDP_, ICMP_, or PKT_ vs UIP_
2014-07-06 17:22:02 -06:00