1.Move __XSTR from include/arch.h to include/irq.h
2.Move FLOAD/FSTORE and REGLOAD/REGSTORE from include/arch.h to src/common/riscv_internal.h
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
The FPU register saving upon vfork entry was missing.
Also added macro that tells the actual size of an FPU reg, instead
of just having a coefficient for qfpu/no-qfpu.
Summary:
- This commit adds support for semihosting and hostfs
Impact:
- None
Testing:
- Tested with nsh and nsh64 (defconfig will be updated later)
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
by renaming riscv_dispatch_syscall to sys_callx, so the caller
don't need the immediate step(syscallx->riscv_dispatch_syscall)
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
This implements initial support for kernel build (address environments,
page allocator) for RISC-V.
This is done a bit differently compared to the ARMV7 implementation:
- Support implemented for Sv39 MMU, however the implementation should be
extensible for other MMU types also.
- Instead of preserving and moving the L1 references around, a canonical
approach is used instead, where the page table base address register
is switched upon context switch.
- To preserve a bit of memory, only a single L1/L2 table is supported,
this gives access to 1GiB of virtual memory for each process, which
should be more than enough.
Some things worth noting:
- Assumes page pool is mapped with vaddr=paddr mappings
- The CONFIG_ARCH_XXXX_VBASE and CONFIG_ARCH_XXXX_NPAGES values are
ignored, with the exception of CONFIG_ARCH_DATA_VBASE which is used
for ARCH_DATA_RESERVE
- ARCH_DATA_RESERVE is placed at the beginning of the userspace task's
address environment
IRQ_NSTACKS, ARCH_CPU_COUNT, CONFIG_SMP_NCPUS all relate to each
other. However, a bit of clean up can be done and everything can
be merged into SMP_NCPUS.
The MPFS bootloader case works also as it requires only 1 IRQ stack
for the hart that executes as bootloader.
ESP32C3 use customized irq encoding so it's hard to share further code
with other risc-v based chips, in this patch, we keep the exception
number definition with risc-v spec.
Signed-off-by: Huang Qi <huangqi3@xiaomi.com>
- Add config "ARCH_USE_S_MODE" which controls whether the kernel
runs in M-mode or S-mode
- Add more MSTATUS and most of the SSTATUS register definitions
- Add more MIP flags for interrupt delegation
- Add handling of interrupts from S-mode
- Add handling of FPU from S-mode
- Add new context handling functions that are not dependent on the trap
handlers / ecall
NOTE: S-mode requires a companion SW (SBI) which is not yet implemented,
thus S-mode is not usable as is, yet.
They are not really defined and used in any where:
uint32_t up_getmisa(void);
uint32_t up_getarchid(void);
uint32_t up_getimpid(void);
uint32_t up_getvendorid(void);
uint32_t up_gethartid(void);
Signed-off-by: Huang Qi <huangqi3@xiaomi.com>
- Add test for mode support, which is architecture dependent
- Add tests for address alignment and region size
- Add option to query for access rights
- The function goes through every PMP entry and tests if an address
range from [base, base+size] has been configured for desired
access rights.
- If several PMP entries match the range and access rights, the
information is combined
- End result is either no access, a partial match was found, or a full
match was found. Details about the partial match are not provided.
The intent for testing access rights and not just blindly applying them
is a case where they are already set in e.g. a bootloader. In this
case, nothing should be done, unless the configuration does not match,
in which case the software must not continue further.
