X0 is always 0 but still should be transfered to the client, but it don't existed in thread context, use any other register for it, and its value will be omitted by gdb client.
Signed-off-by: Huang Qi <huangqi3@xiaomi.com>
The link script of NuttX Simulator is generated through compilation
options. This PR will support configure special data sections in
kconfig to meet the support of 3rd party applications.
we need to follow the syntax of linker script. In 3rd-party applications, some data will be labeled as section:
| a.c:
| struct task_s a __attribute__((section(".data.custom.taska")));
| b.c:
| struct task_s b __attribute__((section(".data.custom.taskb")));
Data of the same type struct can be placed in a fixed location to reduce the overhead caused by searching:
| .data :
| {
| _custom_data_table_start = .;
| KEEP(*(.data.custom.*))
| _custom_data_table_end = .;
| }
Such section declare can be configured via Kconfig in the PR:
| CONFIG_SIM_CUSTOM_DATA_SECTION=" .data : { _custom_data_table_start = .; KEEP(*(.data.custom.*)) _custom_data_table_end = .; } "
Signed-off-by: chao an <anchao@lixiang.com>
In the algorithm there is a subtraction (int - unsigned), which results (potentially overflowed)
unsigned.
Passing this to macro ABS and the assigning to int doesn't work ( unsigned is always >= 0 ).
Fix this by replacing (dangerous) ABS macro with stdlib's standard "int abs(int)"
and change the substraction to (int - int).
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
This is an initial FlexSPI SPI NOR MTD driver for IMX9
This supprts M25P SPI NOR on FlexSPI for now, and can later be extended to other
SPINOR devices if needed. The following configurations are needed to use this driver:
CONFIG_IMX9_FLEXSPI_NOR=y
CONFIG_MTD_M25P=y
In addition, board initialization logic needs to call the imx9_flexspi_nor_initialize
to receive a pointer to the mtd device.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Co-authored-by: Jouni Ukkonen <jouni.ukkonen@unikie.com>
This commit implements a character driver for the general purpose ADC of the BL808, based on the hardware scanning functionality. The driver supports setting different conversion resolutions and the order of channels to be scanned via menuconfig.
Following warnings were caused by incorrect naming of few defines.
chip/sam_mcan.c:415:7: warning: "MCAN1_NTSEG1" is not defined, evaluates to 0 [-Wundef]
415 | # if MCAN1_NTSEG1 > 63
| ^~~~~~~~~~~~
chip/sam_mcan.c:418:7: warning: "MCAN1_NTSEG2" is not defined, evaluates to 0 [-Wundef]
418 | # if MCAN1_NTSEG2 > 15
| ^~~~~~~~~~~~
chip/sam_mcan.c:421:7: warning: "MCAN1_NSJW" is not defined, evaluates to 0 [-Wundef]
421 | # if MCAN1_NSJW > 15
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
This compilation flag was added in the same way as done for esp32
in order to avoid unexpected behaviors when accessing registers
using struct bitfields.
Signed-off-by: Almir Okato <almir.okato@espressif.com>
The Simple Boot feature for Espressif chips is a method of booting
that doesn't depend on a 2nd stage bootloader. Its not the
intention to replace a 2nd stage bootloader such as MCUboot and
ESP-IDF bootloader, but to have a minimal and straight-forward way
of booting, and also simplify the building.
This commit also removes deprecated code and makes this bootloader
configuration as default for esp32 targets and removes the need
for running 'make bootloader' command for it.
Signed-off-by: Almir Okato <almir.okato@espressif.com>
Move and unify map_rom_segments function called when starting
Simple Boot and MCUboot compatible images.
Signed-off-by: Almir Okato <almir.okato@espressif.com>
sometimes ubsan work with asan trigger a mistake report, make it
possible to export library with ubsan, and bypass runtime feature.
Signed-off-by: buxiasen <buxiasen@xiaomi.com>
This current driver does not handle well netpkts used in the
write buffers.
I learned about this document:
https://github.com/apache/nuttx/blob/master/Documentation/components/net/netdriver.rst
After I ported and contributed the original driver.
However from the document, I understand these types of drivers are
simpler to implement and I could simplify the driver and handle
correctly the TCP write buffers.
Add addrenv support for x86_64.
For now we support mapping on PT level, so PD, PDT and PML4 are static
Signed-off-by: p-szafonimateusz <p-szafonimateusz@xiaomi.com>
use new MMU api to implement up_map_region().
The new implementation support maping over 0xffffffff but requires CONFIG_MM_PGALLOC=y
Signed-off-by: p-szafonimateusz <p-szafonimateusz@xiaomi.com>
During the boot phase, when we transition from tee smp to ap smp, we can use a busy waitflag to wait for the completion of the initialization of ap's core0
test:
We can use qemu for testing.
compiling
make distclean -j20; ./tools/configure.sh -l qemu-armv8a:nsh_smp ;make -j20
running
qemu-system-aarch64 -cpu cortex-a53 -smp 4 -nographic -machine virt,virtualization=on,gic-version=3 -net none -chardev stdio,id=con,mux=on -serial chardev:con -mon chardev=con,mode=readline -kernel ./nuttx
Signed-off-by: hujun5 <hujun5@xiaomi.com>
Only in the non-critical region， nuttx can the respond to the irq and not hold the lock
When returning from the irq, there is no need to check whether the lock needs to be restored
test:
We can use qemu for testing.
compiling
make distclean -j20; ./tools/configure.sh -l qemu-armv8a:nsh_smp ;make -j20
running
qemu-system-aarch64 -cpu cortex-a53 -smp 4 -nographic -machine virt,virtualization=on,gic-version=3 -net none -chardev stdio,id=con,mux=on -serial chardev:con -mon chardev=con,mode=readline -kernel ./nuttx
Signed-off-by: hujun5 <hujun5@xiaomi.com>
When the PSRAM is enabled, we should not allocate the TX/RX
buffers there, so we use kmm_calloc here, to make it into IRAM,
so the ethernet controller can read bytes from it.
Add support for XSAVE/XRSTOR to handle x86_64 procesor extended states.
Support for these instructions is required to support AVX instruction set
Signed-off-by: p-szafonimateusz <p-szafonimateusz@xiaomi.com>
Use 32bit operations for id field in intel64_cpu_s which is int type.
This fixes an error that appears when enabling some debug options:
`Error: operand size mismatch for `movq'``
Signed-off-by: p-szafonimateusz <p-szafonimateusz@xiaomi.com>
Intel64 can now boot application cores which is needed for SMP
IMPORTANT: CONFIG_BOARD_LOOPSPERMSEC must be properly configured,
otherwise AP boot sequence can fail due too short delays during the AP startup
Signed-off-by: p-szafonimateusz <p-szafonimateusz@xiaomi.com>
Add support for inter-processor signaling in x86_64 based on up_trigger_irq() interface.
Preparations for SMP.
Signed-off-by: p-szafonimateusz <p-szafonimateusz@xiaomi.com>
reduce the time consumed by function call
test:
We can use qemu for testing.
compiling
make distclean -j20; ./tools/configure.sh -l qemu-armv8a:nsh_smp ;make -j20
running
qemu-system-aarch64 -cpu cortex-a53 -smp 4 -nographic -machine virt,virtualization=on,gic-version=3 -net none -chardev stdio,id=con,mux=on -serial chardev:con -mon chardev=con,mode=readline -kernel ./nuttx
Signed-off-by: hujun5 <hujun5@xiaomi.com>
Use GS base regsiter to store reference to CPU private data.
Then we can easily refer to private CPU data using the GS segment.
Required for SMP support.
Signed-off-by: p-szafonimateusz <p-szafonimateusz@xiaomi.com>
It turns out that the D0 core of the BL808 has an IRQ that represents all interrupt sources for the M0 core. This change uses this IRQ to access these sources, eliminating the need for IPC between M0 and D0.
fix missing reference to comm_region->tsc_khz and
fix 'defined but not used' warnings in arch/x86_64/intel64_rtc.c
Signed-off-by: p-szafonimateusz <p-szafonimateusz@xiaomi.com>
Hide --whole-archive behind Kconfig option for x86.
This option is not needed and breaks ELF modules build.
Signed-off-by: p-szafonimateusz <p-szafonimateusz@xiaomi.com>
on ACRN hypervisor obtaining frequency from CPUID seems to be broken,
so we have to specify this value from Kconfig.
If frequency autodetection is enabled but the returned data are
incorrect - crash early.
Signed-off-by: p-szafonimateusz <p-szafonimateusz@xiaomi.com>
- This PR adds the GPIO Driver for BL808 SoC. This will be used by the upcoming LED Driver for Ox64 Board.
- The BL808 GPIO Driver was derived from the NuttX Driver for BL602 GPIO
Co-Authored-By: Lup Yuen Lee <luppy@appkaki.com>
Squashed:
Initial settings for MCPWM Capture on board level
Created lower half files - compilation ok
Using capture debug features. Simple example on fops works
Successful duty and freq calculation
Documentation update
Fixed and added interupt capabilities for all 3 capture channels
Cleaned defconfig
Renamed macros, added S3 options and moved arch source to common dir
Added support for ESP32S3
Added capture example to defconfig and renamed
For now, IOB off-loading in the wireless driver was removed because
it is not compatible with SMP-enabled devices, which is valid for
ESP32-S3. The performance gain by keeping the IOB off-loading in
the wireless drivers is not exceeded by keeping the flat buffer
approach and enabling `CONFIG_SMP=y`.
This commit modifies the existing serial driver to add support for the remaining UARTs on the BL808. It also introduces support for setting baud rate, character length, stop bits, parity, flow control and which serial port acts as the console.
Use `nxsched_gettid` instead of `nxsched_getpid`. Previously each
kernel thread was modelled as a task, so the pid is the same of the
kthread id. Now, with shared kthread group (introduced by #12320),
the pid of all kthreads will be 0 by design in shared group.
This change implements a system for allowing the D0 core (which runs NuttX) to receive forwarded interrupts from the M0 core. This makes it possible for drivers that rely on interrupts to work with peripherals attached to the M0 core.
cpu0 cpu1:
user_main
signest_test
sched_unlock
nxsched_merge_pending
nxsched_add_readytorun
up_cpu_pause
arm_sigdeliver
enter_critical_section
Reason:
In the SMP, cpu0 is already in the critical section and waiting for cpu1 to enter the suspended state.
However, when cpu1 executes arm_sigdeliver, it is in the irq-disabled state but not in the critical section.
At this point, cpu1 is unable to respond to interrupts and
is continuously attempting to enter the critical section, resulting in a deadlock.
Resolve:
adjust the logic, do not entering the critical section when interrupt-disabled.
test:
We can use qemu for testing.
compiling
make distclean -j20; ./tools/configure.sh -l qemu-armv8a:nsh_smp ;make -j20
running
qemu-system-aarch64 -cpu cortex-a53 -smp 4 -nographic -machine virt,virtualization=on,gic-version=3 -net none -chardev stdio,id=con,mux=on -serial chardev:con -mon chardev=con,mode=readline -kernel ./nuttx
Signed-off-by: hujun5 <hujun5@xiaomi.com>
As suggested in PR:12530, changed the default names of ESP32S3WROOM chips to ESP32S3WROOM1N4,
ESP32S3WROOM2N16R8, ESP32S3WROOM2N32R8, ESP32S3MINI1N8.
Also regenerated all the defconfigs for board configurations.
Added a custom ESP32S3 module for custom flash configurations.
Declared ESP32S3_PSRAM_8M variable with prompt
we can use g_cpu_lockset to determine whether we are currently in the scheduling lock,
and all accesses and modifications to g_cpu_lockset, g_cpu_irqlock, g_cpu_irqset
are in the critical section, so we can directly operate on it.
test:
We can use qemu for testing.
compiling
make distclean -j20; ./tools/configure.sh -l qemu-armv8a:nsh_smp ;make -j20
running
qemu-system-aarch64 -cpu cortex-a53 -smp 4 -nographic -machine virt,virtualization=on,gic-version=3 -net none -chardev stdio,id=con,mux=on -serial chardev:con -mon chardev=con,mode=readline -kernel ./nuttx
Signed-off-by: hujun5 <hujun5@xiaomi.com>
- In some cases, an operational Ethernet MAC may have no PHY, for example
when the system has a direct RMII MAC-to-MAC link.
- New config option STM32H7_NO_PHY
- With this option, PHY-specific code in the ethernet driver is not built
- This option is inherently incompatible with autonegotiation and speed and
duplex settings must be compiled in
To simplify processing, the existed SBI function code is just
invoking the ecall and return the error value. This omits
potential return value in "a1", which is defined in SBI doc.
Add the "sbiret" struct so it can handle all the return value.
In addition, there are some minor improvement:
1. move the SBI related interface to a separate file to make it clean.
2. add all necessary SBI ecall interface macro until version 2.0.
3. add an utilty function to convert sbi error numner to standard
error number.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
This revises `getregXX` and `setregXX` for rv64ilp32 to overcome
the limitation of compiler generated addresses and reach devices
in a larger range.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
This PR adds support for Milk-V Duo S 64-bit RISC-V SBC, based on SOPHGO SG2000 SoC (T-Head C906 Core). Most of the code is derived from NuttX for Ox64 BL808. The source files are explained in the articles here: https://github.com/lupyuen/nuttx-sg2000
Modified Files:
`boards/Kconfig`: Added Milk-V Duo S board
`arch/risc-v/src/sg2000/sg2000_timerisr.c`: Fixed MTIMER_FREQ for sleep() to work correctly
New Files in boards/risc-v/sg2000/milkv_duos:
`src/sg2000_appinit.c`: Startup Code
`include/board.h`: Milk-V Duo S Definitions
`include/board_memorymap.h`: Memory Map
`src/etc/init.d/rc.sysinit`, `rcS`: Startup Script
`src/.gitignore`: Ignore the tmp filesystem
`scripts/ld.script`: Linker Script
`scripts/Make.defs`: Milk-V Duo S Makefile
`src/Makefile`: Milk-V Duo S Makefile
`Kconfig`: Milk-V Duo S Config
`configs/nsh/defconfig`: Build Config for `milkv_duos:nsh`
Updated Documentation:
`platforms/risc-v/sg2000/index.rst`: New page for SOPHGO SG2000 SoC
`platforms/risc-v/sg2000/boards/milkv_duos/index.rst`: Building and booting NuttX for Milk-V Duo S
This PR adds support for the SOPHGO SG2000 SoC, based on T-Head C906 64-bit RISC-V Core. This will be used by the upcoming port of NuttX for Milk-V Duo S SBC.
Most of the code was derived from NuttX for Ox64 BL808. The source files are explained in the articles here: https://github.com/lupyuen/nuttx-sg2000
Modified Files in arch/risc-v:
`Kconfig`: Added ARCH_CHIP_SG2000 for SG2000 SoC
New Files in arch/risc-v:
`include/sg2000/chip.h`: SG2000 Definitions
`include/sg2000/irq.h`: External Interrupts
`src/sg2000/chip.h`: Interrupt Stack Macro
`src/sg2000/sg2000_allocateheap.c`: Kernel Heap
`src/sg2000/sg2000_head.S`: Linux Header and Boot Code
`src/sg2000/sg2000_irq.c`: Configure Interrupts
`src/sg2000/sg2000_irq_dispatch.c`: Dispatch Interrupts
`src/sg2000/sg2000_memorymap.h`: Memory Map
`src/sg2000/sg2000_mm_init.c`, `sg2000_mm_init.h`: Memory Mgmt
`src/sg2000/sg2000_pgalloc.c`: Page Allocator
`src/sg2000/sg2000_start.c`: Startup Code
`src/sg2000/sg2000_timerisr.c`: Timer Interrupt
`src/sg2000/hardware/sg2000_memorymap.h`: PLIC and UART Base Address
`src/sg2000/hardware/sg2000_plic.h`: PLIC Register Addresses
`src/sg2000/Kconfig`: SG2000 Config
`src/sg2000/Make.defs`: Makefile
There is no need to use kernel build for S-mode all the time. As cpu
scratch is supported for non kernel mode build, it is possible to use
flat build for S-mode.
Add flat build support for risc-v S mode.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
This applies uintreg_t in risc-v commons and fixes araised ci issues
for multiple devices. The FLAT build runs on qemu-rv64ilp32 target.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
This adds support of rv64ilp32 toolchain available from Github repo
`ruyisdk/riscv-gnu-toolchain-rv64ilp32`. With this 32-bit nuttx can
be generated for RV64 devices.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
* arch/risc-v/src/common/Toolchain.defs
arch/xtensa/src/lx6/Toolchain.defs
arch/xtensa/src/lx7/Toolchain.defs
- Define SHMODULEFLAGS etc. for sotest/dynload
- Add --entry=__start to SHMODULEFLAGS
* boards/arm64/qemu/qemu-armv8a/scripts/Make.defs
boards/sim/sim/sim/scripts/Make.defs
- Define SHMODULEFLAGS etc. for sotest/dynload
