If a TX DMA completion interrups a forground write.
The TX DMA completion can start a dma_send and it will
then followed by the forground write's dma_send
stoping the,then in progress DMA.
By atomicaly marking the tx dma busy, the forground
write will not perform the dma_send, and will only
enqueue the data. At the next TX dma completion any
data pending in the tx queue will be sent
The logic of the conditional expression that determines whether
the QH is a target QH or not is reversed in the process of canceling
a transfer in INPROGRESS state.
Therefore, the QH in INPROGRESS state is not released and subsequent
communication is not successful.
Checked with CDC-ACM driver and cu command.
Signed-off-by: Takeyoshi Kikuchi <kikuchi@centurysys.co.jp>
Newly added logging in `sched/task_exit.c` obsoletes the existing
ones in `arch/up_exit()`, thus remove the latter to reduce duplications.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
armv8-r/arm_gicv3.c: In function 'gic_validate_dist_version':
armv8-r/arm_gicv3.c:730:9: warning: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'uint32_t' {aka 'long unsigned int'} [-Wformat=]
730 | sinfo("GICD_TYPER = 0x%x\n", typer);
| ^~~~~~~~~~~~~~~~~~~~~ ~~~~~
| |
| uint32_t {aka long unsigned int}
armv8-r/arm_gicv3.c:730:26: note: format string is defined here
730 | sinfo("GICD_TYPER = 0x%x\n", typer);
| ~^
| |
| unsigned int
| %lx
Signed-off-by: chao an <anchao@lixiang.com>
Add ARCH_CHIP_QEMU_TRUSTZONE to enable/disable the TrustZone
support beacause qemu also support enable/disable Arm Security
Extensions: https://qemu-project.gitlab.io/qemu/system/arm/virt.html
when launch.
Signed-off-by: Bowen Wang <wangbowen6@xiaomi.com>
since gcc report the false alarm if the pointer offset from zero address:
inlined from 'up_vectormapping' at chip/dm320_boot.c:162:7,
inlined from 'arm_boot' at chip/dm320_boot.c:211:3:
Error: chip/dm320_boot.c:117:17: error: array subscript 0 is outside array bounds of 'uint32_t[0]' {aka 'long unsigned int[]'} [-Werror=array-bounds=]
117 | ctable[index] = (paddr | mmuflags);
| ~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
The `xxx_ipv6multicast` function in each driver is not adapted to
multiple IPv6 addresses yet, and they're redundant, so try to take them
into common code.
Change:
1. Add MAC `g_ipv6_ethallnodes` and `g_ipv6_ethallrouters` in
`icmpv6_devinit` and call them in `netdev_register`
2. Add multicast MAC for Neighbor Solicitation when adding any IPv6
address, and remove them when IPv6 address is removed
3. Select `NET_MCASTGROUP` when `NET_ICMPv6` because now we need
`d_addmac` when we have ICMPv6
Note:
We want modules outside net stack to call functions like
`netdev_ipv6_add` and never touch the related MAC address, so these MAC
functions are added as internal functions to `net/netdev/netdev.h`
Signed-off-by: Zhe Weng <wengzhe@xiaomi.com>
Add registration function instrumentation API,
which can achieve instrumentation of entering and
exiting functions through the compiler's functionality.
We can use CONFIG_ARCH_INSTRUMENT_ALL to add instrumentation for all
source, or add '-finstrument-functions' to CFLAGS for Part of the
source.
Notice:
1. use CONFIG_ARCH_INSTRUMENT_ALL must mark _start or entry noinstrument_function,
becuase bss not set.
2. Make sure your callbacks are not instrumented recursively.
use instrument_register to register entry function and exit function.
They will be called by the instrumented function
Signed-off-by: anjiahao <anjiahao@xiaomi.com>
The ADC peripheral can only support up to
50MHz on rev V silicon and 36MHz on Y silicon.
The existing driver always used no prescaler
and kept boost setting at 0.
The 1170 usage of the GPR registers is to select the
between GPIO{2|3} or CM7_GPIO{2|3} where as the 1060
it selected ports between 1-6,2-7..4-9 and uses
different GPR registers.
For the 1170 we are defaulting to GPIO{2|3} and not
supporting the swtich to CM7_GPIO{2|3}.
