If using flow control with a high CTS the thread may be
blocked forever on the second transmit attempt due to waiting
on the txdma semaphore. The calling thread can then never
make progress and release any resources it has taken, thus
may cause a deadlock in other parts of the system.
The implementation differs in behavior from interrupt-driven
TX. It should not implicitly wait on a taken semaphore but
return immediately and let the upper layers decide on what to
do next.
If using flow control with a high CTS the thread may be
blocked forever on the second transmit attempt due to waiting
on the txdma semaphore. The calling thread can then never
make progress and release any resources it has taken, thus
may cause a deadlock in other parts of the system.
The implementation differs in behavior from interrupt-driven
TX. It should not implicitly wait on a taken semaphore but
return immediately and let the upper layers decide on what to
do next.
If using flow control with a high CTS the thread may be
blocked forever on the second transmit attempt due to waiting
on the txdma semaphore. The calling thread can then never
make progress and release any resources it has taken, thus
may cause a deadlock in other parts of the system.
The implementation differs in behavior from interrupt-driven
TX. It should not implicitly wait on a taken semaphore but
return immediately and let the upper layers decide on what to
do next.
This commit sets the BLE's interrupt as a IRAM-enabled interrupt,
which enables it to run during a SPI flash operation. This enables
us to create a cache to off-load semaphores and message queues
operations and treat them when the SPI flash operation is finished.
By doing that, we avoid packet losses during a SPI flash operation.
This commit provides an interface to register ISRs that run from
IRAM and keeps track of the non-IRAM interrupts. It enables, for
instance, to avoid disabling all the interrupts during a SPI flash
operation: IRAM-enabled ISRs are, then, able to run during these
operations.
It also makes the code look more similar to the ESP32-S3 SPI flash
implementation by creating a common `esp32_spiflash_init` that is
responsible to create the SPI flash operation tasks. The function
intended to initialize the SPI flash partions was, then, renamed to
`board_spiflash_init`.
Whenever we enter/leave a critical section, the interrupt status is
saved and, then, restored. However, for the ESP32's BLE adapter,
entering/leaving a critical section is done on separate functions
that need to be registered as a callback.
The status flag was being saved as a global variable. However,
calling nested enter_critical_section would overwrite this global
variable that was storing the previous flag and, when leaving the
last critical section, the restored status would be different from
the one expected. The proposed solution for this issue is to create
a global array to store the interrupt status flags for nested calls.
If using flow control with a high CTS the thread may be blocked forever
on the second transmit attempt due to waiting on the txdma semaphore.
The calling thread can then never make progress and release any
resources it has taken, thus may cause a deadlock in other parts of the
system.
The implementation differs in behavior from interrupt-driven TX and the
STM32F7 TXDMA . It should not implicitly wait on a taken semaphore but
return immediately and let the upper layers decide on what to do next.
Some APIs are implemented both in common code and CHIP-specific code,
and the link needs to be based on the implementation in CHIP, so move
NUTTX_CHIP_ABS_DIR before common src.
Signed-off-by: zhanghongyu <zhanghongyu@xiaomi.com>
Because there is no pre-encoding length of the ssid, the ssid including
the Chinese characters whose length is less than 32 after encoding
cann't be translated.
For example, the ssid name is `word人`. After encoding it is `world\xe4\xba\xba` and will not be decoded.
Signed-off-by: liqinhui <liqinhui@xiaomi.com>
These flags are not used in the code.
SERIAL_HAVE_RXDMA and SERIAL_HAVE_TXDMA flags are used instead.
STM32_UART_TXDMA flag is not even defined in Kconfig
Connecting the static page tables to each other was done with the page
table virtual address (riscv_pgvaddr) when the page table physical address
is needed.
I can never remember whether the static page table list contains the
table's physical or kernel virtual address.. Add the fact as a comment
there.
Also add the limitations that come from this static page table approach
for Sv32.
The SSID can be configured with special symbols suach as single
quotations, double quotations and backslashes, which need to be escaped.
Signed-off-by: liqinhui <liqinhui@xiaomi.com>
This adds option to do PMP configuration via mpfs_board_pmp_setup instead
of just opening up everything. In this case, it is up to the specific
board to implement the PMP configuration in whichever way it sees fit.
With TCD set to loop, there is a window where the
DMA has raised Done, but not reloaded the TCD, resetting
count and clearing Done.
In this window imxrt_dmach_getcount could then return 0.
Resulting in imxrt_dma_nextrx returning RXDMA_BUFFER_SIZE.
Which is not a valid index in the FIFO.
Since the count will be set to RXDMA_BUFFER_SIZE. When the DMA
engine completes the TCD reload. The imxrt_dma_nextrx would
return 0. Therefore:
(RXDMA_BUFFER_SIZE - dmaresidual) % RXDMA_BUFFER_SIZE
accomplishes this.
With TCD set to loop, there is a window where the
DMA has raised Done, but not reloaded the TCD, resetting
count and clearing Done.
In this window imxrt_dmach_getcount could then return 0.
Resulting in imxrt_dma_nextrx returning RXDMA_BUFFER_SIZE.
Which is not a valid index in the FIFO.
Since the count will be set to RXDMA_BUFFER_SIZE. When the DMA
engine completes the TCD reload. The imxrt_dma_nextrx would
return 0. Therefore:
(RXDMA_BUFFER_SIZE - dmaresidual) % RXDMA_BUFFER_SIZE
accomplishes this.
With TCD set to loop, there is a window where the
DMA has raised Done, but not reloaded the TCD, resetting
count and clearing Done.
In this window imxrt_dmach_getcount could then return 0.
Resulting in imxrt_dma_nextrx returning RXDMA_BUFFER_SIZE.
Which is not a valid index in the FIFO.
Since the count will be set to RXDMA_BUFFER_SIZE. When the DMA
engine completes the TCD reload. The imxrt_dma_nextrx would
return 0. Therefore:
(RXDMA_BUFFER_SIZE - dmaresidual) % RXDMA_BUFFER_SIZE
accomplishes this.
