It was missing and it wasn't possible to enable I2C (0 and/or 1)
before this fix.
To sum up, this fix implements a I2C register function in ESP32
bring-up routines (esp32_bringup.c) and call if for I2C0 and/or
I2C1 during ESP32 bringup (these function callings are conditioned
by CONFIG_ESP32_I2C (to check if I2C support has been configured),
CONFIG_ESP32_I2C0 (to check if I2C0 support has been configured)
and CONFIG_ESP32_I2C1 (to check if I2C1 support has been configured).
Once this fix is implemented, /dev/i2c0 and/or /dev/i2c1 interfaces
become available and work fine.
The GPIO example was also extended to include testing an interrupt pin.
Co-authored-by: Abdelatif Guettouche <abdelatif.guettouche@espressif.com>
Co-authored-by: Alan Carvalho <alan.carvalho@espressif.com>
This commits adds support for the ESP32-C3 IO Mux and GPIO Matrix. It
also includes necessary board logic to run the GPIO example with 2
outputs.
Co-authored-by: Alan Carvalho <alan.carvalho@espressif.com>
Co-authored-by: Abdelatif Guettouche <abdelatif.guettouche@espressif.com>
I2C3 not worked due to it's GPIO pin definition has been missing on board.h.
Fix it through include two pin macros on stm32l4x3xx_pinmap.h to board.h.
GPIO_I2C3_SCL and GPIO_I2C3_SDA is pointing A7 and B4 respectively.
Summary:
- This commit changes spinlock APIs (spin_lock_irqsave/spin_unlock_irqrestore)
- In the previous implementation, the global spinlock (i.e. g_irq_spin) was used.
- This commit allows to use caller specific spinlock but also supports to use
g_irq_spin for backword compatibility (In this case, NULL must be specified)
Impact:
- None
Testing:
- Tested with the following configurations
- spresnse:wifi, spresense:wifi_smp
- esp32-devkitc:smp (QEMU), sabre6-quad:smp (QEMU)
- maxi-bit:smp (QEMU), sim:smp
- stm32f4discovery:wifi
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
NUTTXNAME is used only as an alias for "nuttx", not actually a
configuration property. Its definition might erroneously imply that the
name of binary image may be configurable, which is not the case.
Summary:
- This commit adds iperf to rndis and rndis_smp defcofigs
Impact:
- rndis and rndis_smp
Testing:
- Tested with iperf
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
The BaseBoard carries Teensy 4.1 SBC. The complete design
of the baseboard (teensy_bb-1.tdb) is available at
https://gitlab.com/pikron/projects/imxrt-devel/-/tree/master/hw
Attempt is to provide configuration which enables most
of interfaces of the BaseBoard and allows runtime applications
loading over TFTP.
Signed-off-by: Pavel Pisa <ppisa@pikron.com>
The ARMv7 specifies minimal alignment to be 8 for EABI. Ensure
that sections are placed with even greater minimal alignment.
Sections final alignment should be adjusted according
to alignment of their inputs, but for some reasons some
combinations lead to .ARM.exidx overlap with .data.
When alignment is increased then the direct fetch of the
fill location
_eronly = ABSOLUTE(.);
does not match with final LMA placement of the .data section.
Use constructs which should result in matching .data LMA
address for all cases
_eronly = ABSOLUTE(.);
Signed-off-by: Pavel Pisa <ppisa@pikron.com>
