* arch/risc-v/src/common/Toolchain.defs
arch/xtensa/src/lx6/Toolchain.defs
arch/xtensa/src/lx7/Toolchain.defs
- Define SHMODULEFLAGS etc. for sotest/dynload
- Add --entry=__start to SHMODULEFLAGS
* boards/arm64/qemu/qemu-armv8a/scripts/Make.defs
boards/sim/sim/sim/scripts/Make.defs
- Define SHMODULEFLAGS etc. for sotest/dynload
For newer devices, IDF bootloader is not supported because the
devices are able to boot directly into NuttX or use MCUBoot to
enable OTA and security features.
This commit enables users to select the legacy bootloader (IDF
bootloader) in `menuconfig` directly. Please note, that this is a
legacy option intended to support devices already deployed and it
isn't recommended for new designs.
*Note:* ldmd2 is ldc2-wrapper, allow using dmd frontend flags.
This support may be extended to gdc (gnu) if nuttx developers demand it
or are interested in it.
Check return value of mpfs_board_pmp_setup() and
jump to mpfs_board_pmp_error() in case of error.
Signed-off-by: Jani Paalijarvi <jani.paalijarvi@unikie.com>
Add the address alignment to keep the constraint of ARMv7-M architecture same as RAM vector.
ARMv7-M architecture describes the vector table address alignment as following.
The Vector table must be naturally aligned to a power of two
whose alignment value is greater than or equal to (Number of Exceptions supported x 4),
with a minimum alignment of 128 bytes.
I wonder why the implementation of arm_vectors.c does not follow
this constraint of address alignment about ARMv7-M architecture.
Although RAM vector is taken care about it.
I think, as the result it was done by linker script on each board.
At our system, NuttX will be started by bootloader.
To fix the address of entry point(__start) I set the address of entry point to beginning of binary,
so the beginning of binary is not a vector table.
At this case, keeping the address alignment constraint of arm_vectors.c is needed.
The Simple Boot feature for Espressif chips is a method of booting
that doesn't depend on a 2nd stage bootloader. Its not the
intention to replace a 2nd stage bootloader such as MCUboot and
ESP-IDF bootloader, but to have a minimal and straight-forward way
of booting, and also simplify the building.
This commit also removes deprecated code and makes this bootloader
configuration as default for esp32s2 targets and removes the need
for running 'make bootloader' command for it.
Signed-off-by: Almir Okato <almir.okato@espressif.com>
Cache the next timeout value in the drivers instance and update the mtimecmp value once. This is advantageous as the opensbi ecall to set the timer is expensive in systems which don't have the supervisor mode timer extension.
This patch changes how user service calls are executed:
Instead of using the common interrupt logic, execute the user service
call directly.
Why? When a user makes a service call request, all of the service call
parameters are already loaded into the correct registers, thus it makes
no sense to first clobber them and then reload them, which is what the
old logic does. It is much more effective to run the system call directly.
During a user system call the interrupts must be re-enabled, which the
new logic does as soon as we know the exception is a user service call
request.
This patch does NOT change the behavior of reserved system calls (like
switch_context), only the user service call request is affected.
Also, convert the type to union; we don't need the list element once
the item has been popped from the free list (the linkage is never needed
when the item is in use).
This provides an alternate tickless scheduling method, which uses the riscv
mtimer as a timebase, allowing the time and timeh registers to used
throughout an application.
The exiting tickless method, using Litex's timer0 has been left in place, as
it is a more performant option, but currently has the potential issue
identified in #11189.
when repeatedly enabling and disabling string-controlled configurations,
the generated toolchain configuration may be incorrect.
Signed-off-by: xuxin19 <xuxin19@xiaomi.com>
Embedded flash can have user signature area on SAMv7. This is a 512
bytes large page whose data are not erased by asserting ERASE pin or by
software ERASE command.
This commit adds arch to board interface for this area. It is possible
to perform read, write and erase operation. SAMV7_USER_SIGNATURE option
has to be set in the configuration.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
By default U(S)ART clocks are enabled in sam_lowput.c but
configuration check from sam_config.h may override USART configuration
and prevent clocks from been enabled.
This commit fix inconsistency in U(S)ART pinmux and clock configuration
Signed-off-by: Petro Karashchenko <petro.karashchenko@gmail.com>
This is to fix issue in [this log](https://github.com/apache/nuttx/actions/runs/9173629303/job/25222879619):
```
Configuration/Tool: esp32c3-generic/twai esp32c6-devkitm/twai esp32c6-devkitc/twai esp32h2-devkit/twai
Error: common/espressif/esp_twai.c:242:7: error: variable 'ret' set but not used [-Werror=unused-but-set-variable]
```
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
Search and replace ARCH_BOOT_EL3 with more generic
ARCH_ARM64_EXCEPTION_LEVEL that holds the EL level
in an integer variable.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
This provides a capable bootloader that may be run from OCRAM.
The OCRAM contains regions that are always zero, so the linker
file avoids those with best effort.
iMX9 infrastructure expects:
- 0x20480000 (Start of OCRAM, AHAB)
- 0x2049a000 (NuttX or SPL)
- 0x204e0000 (ARM Trustzone, not used)
When started from SD-card, the offsets are:
- 0x1f000 with AHAB
- 0xa000 without AHAB
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
