There is a problem with the original driver reading and writing behavior, refer to the driver of mpu60x0 to make corresponding changes.
Signed-off-by: xinbingnan <xinbingnan@xiaomi.com>
* Simplify EINTR/ECANCEL error handling
1. Add semaphore uninterruptible wait function
2 .Replace semaphore wait loop with a single uninterruptible wait
3. Replace all sem_xxx to nxsem_xxx
* Unify the void cast usage
1. Remove void cast for function because many place ignore the returned value witout cast
2. Replace void cast for variable with UNUSED macro
boards: cxd56xx: add SCU sensors
* drivers: platform: add Avago APDS9930 Proximity and Ambient light Sensor
This sensor is connected to the SCU on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: spresense: add Rohm BH1721FVC Ambient Light Sensor
This sensor is connected to the SCU on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: spresense: add Rohm BH1745NUC Color Sensor
This sensor is connected to the SCU on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: spresense: add Rohm BM1383GLV/BM1383AGLV Pressure Sensor
This sensor is connected to the SCU on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: spresense: add Rohm BM1422GMV/BM1422AGMV Magnetic Sensor
This sensor is connected to the SCU on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: spresense: add Bosch BMI160 Sensor support
This sensor is connected to the SCU on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: spresense: add Bosch BMP280 Barometic Pressure Sensor
This sensor is connected to the SCU on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: spresense: add Kionix KX022/KX122 Acceleration Sensor
This sensor is connected to the SCU on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: spresense: add Murata LT1PA01 Proximity and Ambient light Sensor
This sensor is connected to the SCU on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: spresense: add Rohm RPR0521RS Proximity and Ambient light Sensor
This sensor is connected to the SCU on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: sensors: bmi160: add optional I2C address
Add a menu option for the case when the SDO pin is pulled to VDDIO
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
configs: spresense: enable BMI160_I2C sensor
* drivers: sensors: add BMI160 driver
Enable driver support for the Bosch BMI160 Inertial
Measurement sensor
This driver can be used with the BMI160 sensor connected over
SPI or I2C bus
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: enable BMI160_I2C sensor
Enable BMI160 sensor connected over I2C on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
