Squashed commit of the following:
arch/arm/src/max326xx and configs/max32660-evsys/nsh/defconfig: Work out some issues related to MAX326xx configuration.
configs/max32660-evsys: Add unverified board support framework.
stm32/stm32_adc: major refator
stm32/stm32_adc: use STM32 ADC IP core version and ADC available functions instead of chip family names in conditional compilation
stm32/chip: replace family specific ADC headers with STM32 ADC IP core version headers
stm32/stm32_adc: configurable sample time supported for all chips, not only L1
stm32/stm32_adc: enable/disable interrupts supported for all chips, not only L1
stm32/stm32_adc: resolution configuration
stm32/stm32f33xxx_adc: remove wrong assertion
configs/nucleo-f303ze: support for ADC and ADC example
configs/stm32f429i-disco: support for ADC and ADC example
Approved-by: GregoryN <gnutt@nuttx.org>
NuttX: STM32F407VG has only one DAC
NDAC=2 causes compilation error when trying to use e.g. STM32_DAC1_CR macro.
Approved-by: GregoryN <gnutt@nuttx.org>
imxrt:Clock config fixes and board.h sets sources and divisors
* imxrt:clockconfig bug fix & Board config set clocks
Fixed logic that was not clearing bits as ~ was
mising in &= mask operations.
Use valuse from the board.h file so set the Mux that
selects the clock sources.
Use board defined PODF values to select clock.
Only configure USDHC2 clocks when board defines clocks.
* imxrt1050-evk:Board setting used to set LSPI and USDHC Clocks
Approved-by: GregoryN <gnutt@nuttx.org>
This change is needed specifically for the case where a bootloader sets the SPE bit before starting NuttX. In that case, the test in the SPI driver is bogus. This change fixes that by assuring that NuttX has booted and initialized at least once (whether or not SPE is set) before the driver starts refusing to initialize.
arch/arm/stm32*: Don't rely on SPI_CR1_SPE to determine if peripheral has been initialized yet.
Approved-by: GregoryN <gnutt@nuttx.org>
Fixes Kconfig options to include all STM32F20XX processors, not just STM32F207
* arch/arm/src/stm32: Fixes Kconfig options to include all STM32F20XX processors, not just STM32F207
* arch/arm/src/stm32: Removes redundant STM32_STM32F429 depends from Kconfig. STM32F4XXX already does this
Approved-by: GregoryN <gnutt@nuttx.org>
In addition to the problems that were previously identified there were a few other bits and pieces outstanding;
* Timing was dependent on CPU speed rather than absolute time
* End of transfer handling was a bit mixed up
* It's possible for data to still be in the FIFO (i.e. not have reached
the card) when a next write is requested, so we need to wait for that to
complete
* Interrupt Status could be carried over from one transfer episode to the
next, corrupting progress
* Multi-descriptor DMA writing simply wasn't implemented, but there were no
indications ... it just failed silently
Master imxrt
* imxrt:Fix typos bit# and names
* imxrt:wdog Registers are 16 Bits
* imxrt:wdog Update has to be within 255 clocks of unlock
* imxrt:clockconfig Fix comments
* imxrt1050-evk:board.h Fix comments
* imxrt:imxrt_ccm.h Define Mux Selects for board.h use
* imxrt:clockconfig Allow better control from board.h
1) Allows a board config clock setting to be defined
in terms of the /n values shown in Figure 18-2.
Clock Tree of the i.MX RT1050 Processor Reference
Manual, Rev. 1, 03/2018
2) Allows the clock multipelx selection to be made in
The board config.
* imxrt1050-evk:Define board clocking based on divisor and muxes
Approved-by: GregoryN <gnutt@nuttx.org>
