arch/z80/src/ez80: Clean-up RTC driver; get a clean compilation. Still untested.
arch/z80/src/ez80: This brings the RTC to code complete, but does not yet compile.
arch/z80/src/ez80/ez80_rtc.c: Bring in badly ported RTC driver from STM32F4. Little more than naming changing at this point not even ready to attempt comilation
arch/z80/src/ez80: Add RTC driver. Initial commit is just the STMF4 RTC driver with name changes.
configs/makerlisp/src/ez80_spi.c: Add hooks needed by SPI driver. Move SPI MMC/SD chip selected configuration from ez80_lowinit.c to here as it done in other NuttX architectures. This enables support for multiple devices on the SPI bus.
arch: arm: cxd56xx: add support for USB and SDIO
* arch: arm: cxd56xx: add support for USB connectivity
Add basic support for USB connectivity
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add SDHCI support
We add SDHCI driver for the cxd56xx
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arch: arm: cxd56xx: add Package Configuration
The CXD56xx can come in FCBGA 185 pin or WLCSP 100 pin package.
For each package we have to pick the right pin setup.
The default configuration is set to FCBGA 185 pin package
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Squashed commit of the following:
configs/makerlisp: Update comments about use of serial console.
configs/makerlisp: Add LED support, remove vestiges of button support (the board has no user buttons). Add support for SPI-based MMC/SD card slot.
arch/z80/src/ez80: Fix some link problems.
libs/libc/syslog/lib_syslog.c: The ZDS-II toolchain does not declare va_coy in stdarg.h. I think that the use of va_copy in vsyslog() is no necessary.
configs/makerlisp: Initial configuration directories cloned from ez80f910200zco with little more than naming changes.
ez80: Fixing a few more compile problems. I am afraid that the 5.3.0 compiler it too buggy to use.
ez80: Additional build-related fixed.
eZ80: Updating to use the newest ZDSII 5.3.0 toolchain.
Improvements for STM32 PWM
arch/arm/src/stm32/stm32_pwm: add support for all PWM modes
arch/arm/src/stm32/stm32_pwm: add interface to change PWM mode
arch/arm/src/stm32/stm32_pwm: refactor pwm_mode_configure()
arch/arm/src/stm32/stm32_pwm: STM32_PWM_CHANx corresponds to the timer channel and STM32_PWM_OUTx corresponds to the timer channel output
arch/arm/src/stm32/stm32_pwm: add CHAN5 and CHAN6 to PWM_TIMx_NCHANNELS
arch/arm/src/stm32/stm32_pwm: calculate the PWM_TIMx_NCHANNELS if CONFIG_STM32_PWM_MULTICHAN is selected
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Squashed commit of the following:
arch/arm: Rename include/stm32f0l0 and src/stm32f0l0 to stm32f0l0g0.
Change all occurrences of lower-case stm32f0l0 to stm32f0l0g0.
Change all occurrences of upper-case STM32F0L0 to STM32F0L0G0.
arch/mips/src: Previous commit used CP0 register definitions that were not defined in the cp0.h header file. Probably these were from the Microchip hacked up GCC toolchain but are not generally available. Fix: Add definitions to NuttX cp0.h header file.
mm/iob: Eliminate some warnings about testing the value of an undefined pre-processor variable.
