* imxrt: GPIO make tables const
* imxrt: Call out to board to set up FlexRAM
* imxrt: Add Knob for adding the ROM bootloaders 40Kib of RAM to heap
* imxrt: imxrt1060-evk:Add the ability to run from OCRAM
* arch/arm/src/imxrt/imxrt_usbdev.c: Add USB Device support for i.MX RT (USB OTG1)
Based on the LPC43xx USB Device driver.
* imxrt:usbotg Nxstyle fixes
Co-authored-by: thomasactia <61285689+thomasactia@users.noreply.github.com>
board/z80/ez80/*/scripts/Make.defs: Fix optimization definition use in assembly flags. It was using the compiler optimization settings instead of the assembler optimization settings. Hence, enabling optimization would could cause assembler command line errors.
arch/z80/src/ez80/Toolchain.defs: Back out some work arounds. Now compiler optimization flags can again set set without assembler command line errors.
boards/z80/ez80/z20x/README.txt: Trivial update to size/optimization discussion.
The eZ80F92 interrupt controller is very different from the eZ80F91. The eZ80F91 has:
1. Four byte interrupt vectors
2. The vector base address register is 16-bit so the vector table can lie in RAM
Whereas the eZ80F92 has:
1. Two byte interrupt vectors
2. An 8-bit vector base address
This means that the vectors must lie in the first 16-bits of FLASH and there must be a "trampoline" to get to interrupt handlers outside of the first 64-Kb of FLASH.
arch/z80/src/ez80/Toolchain.defs: Correct some CFLAGS when optimization suppressed.
arch/z80/src/ez80/Kconfig arch/z80/src/ez80/ez80_emac.c: Remove configuration option for selecting EMAC RAM address. This is duplicated and possibly conflicting. The correct address for the RAM is provided in the linker command file. The RAM should be configured once and using this single definitions.
arch/z80/src/ez80/ez80_startup.asm and arch/z80/src/ez80/ez80f9*_init.asm. Move RAM and FLAH intialization out of MCU-specific logic to common start-up logic. We cannot call any functions until SRAM is initialized and the stack is properly initialized because the return address is stored on the stack. Use internal SRAM for the IDLE stack to avoid the chicken'n'egg problem.
boards/z80/ez80/z20x/configs/sdboot/sdboot.zdsproj: Discuss build environments.
CONFIG_FAT_MAXFNAME is set to 255 and CONFIG_NAME_MAX is set to 765
which can support max file name including Japanese characters.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
arch/z80/src/ez80/Toolchain.defs: Update some CFLAGS to match CFLAGS from ZDS-II IDE. Apparently, we must say that the CPU is an eZ80F91 event when compiler for eZ80F92.
boards/z80/ez80/z20x: Update linker scripts.
Squashed commit of the following:
commit 685951b5385062035ac558df1112353c9441c910
Author: Adam Feuer <adam@starcat.io>
Date: Mon Feb 24 16:33:00 2020 -0800
fixed typo in readme
commit ad1d3289b48af0de3095e3f365429017e57278b3
Author: Adam Feuer <adam@starcat.io>
Date: Mon Feb 24 16:07:48 2020 -0800
simulator host route helper script and docs
Squashed commit of the following:
commit cf5cddcf55a155303cb5abb1aa026f6dcaf369ca
Author: Adam Feuer <adam@starcat.io>
Date: Mon Feb 24 15:50:40 2020 -0800
syslog on console to fix compile error
commit def1bb73fcfbc8b115c55d9f4544b97d583807f2
Author: Adam Feuer <adam@starcat.io>
Date: Mon Feb 24 15:46:13 2020 -0800
formatting as per PR feedback; removed ping
commit b179fd8831b77fbbe85527a4ab3161e1f1ca1e43
Author: Adam Feuer <adam@starcat.io>
Date: Mon Feb 24 15:45:49 2020 -0800
formatting as per PR feedback
commit e3280bede9798d9a00b118e126c02ceab497e33a
Author: Adam Feuer <adam@starcat.io>
Date: Mon Feb 24 13:56:50 2020 -0800
add simhostroute.sh description to readme
commit 09a6b0ca3bacf005c2a79102141ae8cc3eb91849
Author: Adam Feuer <adam@starcat.io>
Date: Sun Feb 23 17:38:40 2020 -0800
fixed error in simhostroute.sh usage docs
commit d838582119d43ee2002ce3808051c82b23e98c58
Author: Adam Feuer <adam@starcat.io>
Date: Sun Feb 23 17:28:35 2020 -0800
added tcpblaster defconfig and updated docs
commit af3d2d6591f12d1127027fdd363858052094e624
Author: Adam Feuer <adam@starcat.io>
Date: Sun Feb 23 17:21:29 2020 -0800
added info about capabilities and running as root
commit 6359cfdfedefc818b169455401942d3d33a59f41
Author: Adam Feuer <adam@starcat.io>
Date: Sun Feb 23 17:20:42 2020 -0800
updated network linux readme
commit 47feb08aa74e4b1fc6c802567bc777d31e7c9a83
Author: Adam Feuer <adam@starcat.io>
Date: Sun Feb 23 17:09:04 2020 -0800
initial addition
* tools/zds/zds_Config.mk: Move boards/z80/ez80/scripts/eZ80_Config.mk to tools/zds/zds_Config.mk where it can be shared by other ZDS-II platforms.
* boards/z16/z16f: Duplicate changes for new ZDS-II support from ez80
* boards/z80/z8: Duplicate changes for new ZDS-II support from ez80
* arch/z16/src/z16f/Toolchain.defs: Create required Toolchain.defs file for Z16f
Eliminate the MOVEOBJ definition from tools/Config.mk, Makefiles, and other locations. The MOVEOBJ definition was used to work around the case where the object output of a compile or assemble is in a different directory than the source file. The ZDS-II tools have no command line option to perform this move; MOVEOBJ handled the move as a post-compiler operation.
MOVEOBJ is no longer needed because this the ez80 COMPILE and ASSEMBLE definitions now handle all of the object file movement cases.
tools/zds/zdsgen.c: Remove this program. It should have been a simpler way to manage ZDS-II compiler and assember differences. However, the compiler arguments needed to pass through too many layers of bash command line modifications and, as a result, it was not possible to retain quotes on critical strings. This approch was abandoned for an alternative approach.
boards/z80/ez80/scripts/eZ80_Config.mk: Add definitions to move the object files as necessary. This seems to work well and is implemented for both native and Cygwin Windows build -- but only for the Z20x.
tools/zds: A new tool sub-directory intended to hold tools for making life working with the ZDS-II toolchain less painful.
tools/zds/zdsar.c: This is a wrapper around the ZDS_II librarian. It simplifies the build scripts by replacing large sequences of complex Bash script that were added to the build files. Not only does this clean up the build files but it also improves performance and, more importantly, provides a common solution for the Windows native build case. This tool should work with all ZDS-II based platforms including z8, zNeo, and ez80.
tools/README.txt: Add a brief description about the zds sub-directory. Also re-ordered some tool descriptions. They are supposed to be in alphabetical order, but this seems to have fallen apart.
boards/z80/ez80/scripts/eZ80_Config.mk: Updated to use tools/zds/zdsar.exe.
This includes some fixes for the ez80 build including:
1. Ability to handle decorated object file names,
2. Ability to handle libraries described with absolute paths
This commit address only the POSIX build and needs to be updated
for the Windows native build.
arch/z80/arc/ez80/Toolchain.sh: Move more common toolchain definitions from Make.defs.
boards/z80/ez80/scripts/eZ80_Config.mk: Move common defines that override tools/Config.mk to this new file.
This does not solve the ez80 build problem yet but does assure that when the solution is in place, it will automatically apply to all present and future ez80 configurations.
to avoid shell complain that @echo can't find if the variable expand in the compound
command(e.g. ARLOCK) and remove $(Q) before $AR so the result is almost same as before.
Enable optimization and generate debug symbols.
Enable scheduler instrumentation and spinlock irq.
Add applications such as hello, ostest and taskset.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Update linker scripts to provide _ramfuncs sections for SAMv7 based boards. This corrects undefined reference to _ramfuncs when CONFIG_ARCH_RAMFUNCS is enabled (Issue #304)
Largely copy-and-paste from stm32f4discovery.
Also arch/arm/src/armv7-m/mpu.h: Ensure RBAR alignment
Fix crashes on init task startup I observed on qemu-system-arm -M lm3s6965evb.
Because we can get the same function by CONSOLE_SYSLOG/syslog_console_init.
BTW, it isn't a good choice to use g_ramlogfops as /dev/console since nsh
will read back what it send out which will surprise most people.
This commit adds automounter and BOARDCTRL_RESET support for SAMV71 and verified on Atmel SAMV71-XULT. Also, some fixes of Kconfig and missing uerr/uinfo definition.
To ensure size_t same as toolchain definition in the first place and rename CXX_NEWLONG to ARCH_SIZET_LONG. The change also check whether __SIZE_TYPE__ exist before CONFIG_ARCH_SIZET_LONG so our definition can align with toolchain(gcc/clang) definition automatically.
Basically a copy-and-paste from spresense.
But I added -mlong-calls for ELF to avoid out of range relocations.
(Isn't it necessary for spresense?)
gnu-elf.ld is a copy from stm32f4discovery. I changed the license
of this file with a permisson of @patacongo.
Historically, the loopback driver used the largest packet size of all enabled link layer protocols. This permitted packets to be forward via the loopbak device with no major loss of performance. However, in experimenting with configurations where no other link layer protocols were enabled, this means the loopback packet size was set to the smallest possible size, to the SLIP minimum of 296 bytes. This resulted in terrible loopback performance.
This commit adds an option to increase the loopback packet size with the option CONFIG_NET_LOOPBACK_PACKETSIZE.
The loopback driver packet buffer should be quite large. The larger the loopback packet buffer, the better will be TCP performance of the loopback transfers. The Linux loopback device historically used packet buffers of size 16Kb, but that was increased in recent Linux versions to 64Kb. Those sizes may be excessive for resource constrained MCUs, however.
The network still enforces the lower limit that is the maximum packet size of all enabled link layer protocols. But this new option permits the loopback packet size to be increased from that.
* net/Kconfig: Adds CONFIG_NET_LOOPBACK_PKTSIZE option
* include/nuttx/net/netconfig.h: Assures that the packet size that is used is at least as large as the largest packet size of other link layer protocols.
* drivers/net/loopback.c: Use that larger packet size.
* boards/sim/sim/sim/configs/tcploop/defconfig: Set the loopback packet size to 1500
Call xxx_timer_initialize from clock subsystem to make timer ready for use as soon as possiblei and revert the workaround:
commit 0863e771a9
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Apr 26 07:24:57 2019 -0600
Revert "sched/clock/clock_initialize.c: clock_inittime() needs to be done with CONFIG_SCHED_TICKLESS and clock_initialize should skip clock_inittime() for external RTC case since the RTC isn't ready yet."
This reverts commit 2bc709d4b9.
Commit 2bc709d4b9 was intended to handle the case where up_timer_gettime may not start from zero case. However, this change has the side-effect of breaking every implementation of tickless mode: After this change the tickless timer structures are used before they are initialized in clock_inittime(). Initialization happens later when up_initialize is called() when arm_timer_initialize().
Since the tickless mode timer is very special, one solution might be to
1. Rename xxx_timer_initialize to up_timer_initialize
2 Move up_timer_initialize to include/nuttx/arch.h
3. Call it from clock subsystem instead up_initialize
Basically, this change make timer initialization almost same as rtc initialization(up_rtc_initialize).
For now, however, we just need to revert the change.
* include: Introduce elf64.h and elf.h
Added elf64.h for 64bit ELF support and moved common definitions
from elf32.h to elf.h. Also introduced Elf_xxx to be used in
common libraries such as binfmt.
* binfmt, include, modlib, module: Add support for ELF64
Elf_xxx must be used instead of Elf32_xxx to support ELF64.
To use ELF64, CONFIG_ELF_64BIT must be enabled.
* binfmt, modlib: Add support for relocate address
* arch: risc-v: Add include/elf.h
* libs: machine: Add risc-v related files.
NOTE: Currently only supports ELF64
* boards: maix-bit: Add elf and posix_spawn configurations
* boards: maix-bit: Add support for module configuration
* S32K add support for Nxp drone boards
* Update arch/arm/src/s32k1xx/hardware/s32k1xx_rtc.h codestyle
Co-Authored-By: David Sidrane <David.Sidrane@Nscdg.com>
Co-authored-by: Jari van Ewijk <jari.vanewijk@nxp.com>
Co-authored-by: David Sidrane <David.Sidrane@Nscdg.com>
It seems that "ld -r" on macOS doesn't include objects from
libraries for common symbols. Because of that, sim build
ends up with undefined references to globals like g_binfmts
and g_mmheap.
Namely this changes HOSTOS for macOS from "Other" to "Darwin".
Also, suppress the following harmless messages during a "make":
(Missing redirect in tools/Makefile.host)
uname: illegal option -- o
usage: uname [-amnprsv]
Add CONFIG_MMCSD_SDIO=y to configuration. This eliminates the following error found in build testing: lpc17_40_bringup.c: undefined reference to mmcsd_initialize
This change backs out a portion of ac4735cf58 and corrects the dependencies on CONFIG_NETUTILS_TELNETD. Without this change, the configuration will not build. It will fail with:
nsh.h:154:4: error: #error "No NSH frtont end defined."
Author: Xiang Xiao <xiaoxiang@xiaomi.com>
Fix warning: selects SDIO_DMA or SDIO_BLOCKSETUP which has unmet direct dependencies (MMCSD)
Fix warning: selects NETDEV_TELNET which has unmet direct dependencies (NETDEVICES && NET && NET_TCP)
Fix warning: selects ARCH_PHY_INTERRUPT which has unmet direct dependencies (NETDEVICES && ARCH_HAVE_PHY)
Fix warning: selects USBHOST_HAVE_ASYNCH which has unmet direct dependencies (USBHOST)
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Gregory Nutt <gnutt@nuttx.org>
Run all .c and .h files modified in this PR through nxstyle and correct all coding standard problems.
Xiang Xiao <xiaoxiang@xiaomi.com>
Remove TIME_EXTENDED option to more conform C standard
Note: the code/data size increment is small
