* Simplify EINTR/ECANCEL error handling
1. Add semaphore uninterruptible wait function
2 .Replace semaphore wait loop with a single uninterruptible wait
3. Replace all sem_xxx to nxsem_xxx
* Unify the void cast usage
1. Remove void cast for function because many place ignore the returned value witout cast
2. Replace void cast for variable with UNUSED macro
The same interrupt handler is entered with the device structure parameter in all situations,
multiple or single PCA. One should still be careful if multiple PCA devices share the same IRQ.
This commit backs out most of commit b4747286b1. That change was added because sem_wait() would sometimes cause cancellation points inappropriated. But with these recent changes, nxsem_wait() is used instead and it is not a cancellation point.
In the OS, all calls to sem_wait() changed to nxsem_wait(). nxsem_wait() does not return errors via errno so each place where nxsem_wait() is now called must not examine the errno variable.
In all OS functions (not libraries), change sem_wait() to nxsem_wait(). This will prevent the OS from creating bogus cancellation points and from modifying the per-task errno variable.
sched/semaphore: Add the function nxsem_wait(). This is a new internal OS interface. It is functionally equivalent to sem_wait() except that (1) it is not a cancellation point, and (2) it does not set the per-thread errno value on return.
sched/semaphore: Add nxsem_post() which is identical to sem_post() except that it never modifies the errno variable. Changed all references to sem_post in the OS to nxsem_post().
sched/semaphore: Add nxsem_destroy() which is identical to sem_destroy() except that it never modifies the errno variable. Changed all references to sem_destroy() in the OS to nxsem_destroy().
libc/semaphore and sched/semaphore: Add nxsem_getprotocol() and nxsem_setprotocola which are identical to sem_getprotocol() and set_setprotocol() except that they never modifies the errno variable. Changed all references to sem_setprotocol in the OS to nxsem_setprotocol(). sem_getprotocol() was not used in the OS
libc/semaphore: Add nxsem_getvalue() which is identical to sem_getvalue() except that it never modifies the errno variable. Changed all references to sem_getvalue in the OS to nxsem_getvalue().
sched/semaphore: Rename all internal private functions from sem_xyz to nxsem_xyz. The sem_ prefix is (will be) reserved only for the application semaphore interfaces.
libc/semaphore: Add nxsem_init() which is identical to sem_init() except that it never modifies the errno variable. Changed all references to sem_init in the OS to nxsem_init().
sched/semaphore: Rename sem_tickwait() to nxsem_tickwait() so that it is clear this is an internal OS function.
sched/semaphoate: Rename sem_reset() to nxsem_reset() so that it is clear this is an internal OS function.
PCA9555 Driver: Replace the signalling logic with a simple callback using the new definitons of ioexpander.h. This repartitioning of functionality is necessary because (1) the I/O expander driver is the lower-lower part of any driver that uses GPIOs (include the GPIO driver itself) and should not be interacting directly with the much higher level application layer. And (2) in order to be compatible with the GPIO driver (and any arbitrary upper half driver), the PCA9555 should not directly signal, but should call back into the upper half. The upper half driver that interacts directly with the application is the appropriate place to be generating signal.
are held in the microcontrollers memory and only written to the IO-Expander.
This reduces bus traffic and is more error-proof than the normal read-
modify-write operation.
Retry Mode: If enabled and an error occurs while writing to the IO-Expander the
current transmission is automatically repeated once.
-headers in nuttx/ioexpander to define the "generic" ioexpander framework
-files in drivers/ioexpander for the implementation of the NXP PCA9555 framework
-bindings in drivers/Kconfig and drivers/Makefile
From Sebastien Lorquet
