Update PLL configuration parameters to match the values provided
by the vendor.
Also remove extra call to mpfs_pll_config() as it's already called
at mpfs_clockconfig().
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
This patch adds corrected implementation of FLASH memory to be used
with progmem driver for use with mtd filesystems like nxffs or smartfs.
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
Summary:
- I noticed that QEMU shows a high CPU load.
- This commit re-adds imx_idle.c to avoid this issue.
Impact:
- None
Testing:
- Tested with sabre-6quad:smp with QEMU
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
This patch implements working support for EXTI GPIO.
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
--
v1 -> v2:
Suggested by: Petro Karashchenko
- change (1 << n) to (1 << (n)) in macro definition
- change 1 << X to (1 << X) in code
- fix alignment
v2 -> v3:
Suggested by: Petro Karashchenko
- I was supposed to change (1 << pin) to 1 << pin, not the other way around:)
Summary:
- I noticed that sometimes uart shows nothing on the maix-bit board.
- This commit adds a workaround to avoid such the issue
Impact:
- k210 only
Testing:
- Tested with maix-bit
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
This provides USB composite (CDC/ACM and Mass Storage) support
for mpfs board. In addition, a number of USB fixes are included:
- Support for Setup Out packets
- Proper support for larger than packet size writes
- Finishing setup packets properly
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Output "X" with showprogress and make a system reset.
Silently ignoring failed training is dangerous and will cause random behaviour if DDR is used
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
This patch adds new chip family, stm32wl5x. This is bare minimum
implementation of said chip. I've tested this by running nsh.
There are only two chips in this family, stm32wl55 and stm32wl54.
The only difference between them is that stm32wl55 has LORA.
stm32wl5 is dual CPU (not core!). Right now only CPU1 is implemented.
CPU0 has access to radio hardware (while CPU1 does not). Chip is
designed so that CPU0 handles radio traffic while CPU1 does the
heavy lifting with data - there is communication pipe between two
CPUs.
I plan to use nuttx on CPU1 and LORA from stm32cube on CPU0 so I
don't have implementing CPU0 right now - once we have working LORA
in nuttx this may change.
Peripherals (except for radio) are shared so it's best to focus on
CPU1 to initialize all peripherals so that CPU0 can only use them
later. There is no real benefit to implement CPU0 if we don't have
working LORA/radio support in nuttx.
In time I will be implementing more and more things from this chip.
Right now I would like this minimal implementation to be merged in
case someone wants to work on this chip as well.
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
---
patch v1->v2
- fixed formatting (suggested by Alan Carvalho de Assis)
- rebased patch to master (previous patch was based on nuttx-10.2
and did not compile on master)
arch/x86/Kconfig:28:warning: choice value used outside its choice group
arch/x86/Kconfig:29:warning: defaults for choice values not supported
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
We might have a situation where an allocation will be requested before
the call to `up_initialize` is performed. For the current code, this
situation is the stack for the CPUs in SMP mode.
Beside this issue, it's natural to have the internal heap initialized
with the other heaps.
Signed-off-by: Abdelatif Guettouche <abdelatif.guettouche@espressif.com>
jumping back to the assembly signal trampoline and getting into its
infinite loop.
Signed-off-by: Abdelatif Guettouche <abdelatif.guettouche@espressif.com>
Change pin initialization timing for camera from board power on to camera device
power on for the following purposes.
- avoid unnecessary power consumption
- Make the corresponding pins available for other uses when camera is not in use
