Add a static port-based VLAN configuration for KSZ9477 switch. This doesn't
use the VLAN tagging, but is a switch's internal mechanism to simply configure
if the packet forwarding is allowed from one port to another.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
In order to obtain best accuracy over temperature range,
particularly in low temperature, it is recommended to
compensate the non-linearity over the temperature.
ref: ENG_DS_MS5611-01BA03_B3.pdf
ENG_DS_MS5607-02BA03_B4.pdf
Signed-off-by: Takumi Ando <t-ando@advaly.co.jp>
In function 'unlock_evtbufinst',
inlined from 'parse_altcompkt' at modem/alt1250/alt1250.c:919:7,
inlined from 'altcom_recvthread' at modem/alt1250/alt1250.c:968:21:
Error: modem/alt1250/alt1250.c:385:3: error: 'inst' may be used uninitialized [-Werror=maybe-uninitialized]
385 | nxmutex_unlock(&inst->stat_lock);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
modem/alt1250/alt1250.c: In function 'altcom_recvthread':
modem/alt1250/alt1250.c:822:26: note: 'inst' was declared here
822 | FAR alt_evtbuf_inst_t *inst;
| ^~~~
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
The Goldfish FB register should be optimized by considering the need to pass in parameters for base and irq.
Signed-off-by: jianglianfang <jianglianfang@xiaomi.com>
The opening and closing of the window has been associated with the opening and closing of fb, but the LCD has not yet been optimized. The window will only open when sim_x11openwindow is called, and similarly, the window will only close when sim_x11closewindow is called.
Signed-off-by: jianglianfang <jianglianfang@xiaomi.com>
The `xxx_ipv6multicast` function in each driver is not adapted to
multiple IPv6 addresses yet, and they're redundant, so try to take them
into common code.
Change:
1. Add MAC `g_ipv6_ethallnodes` and `g_ipv6_ethallrouters` in
`icmpv6_devinit` and call them in `netdev_register`
2. Add multicast MAC for Neighbor Solicitation when adding any IPv6
address, and remove them when IPv6 address is removed
3. Select `NET_MCASTGROUP` when `NET_ICMPv6` because now we need
`d_addmac` when we have ICMPv6
Note:
We want modules outside net stack to call functions like
`netdev_ipv6_add` and never touch the related MAC address, so these MAC
functions are added as internal functions to `net/netdev/netdev.h`
Signed-off-by: Zhe Weng <wengzhe@xiaomi.com>
and optimize the critical section usage
1.Remove the unnecessary critical section in ramlog_readnotify
2.Move the enter/leave critical section out of ramlog_pollnotify loop
3.Move the critical section of ramlog_addchar to caller
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
1.Remove RAMLOG_OVERWRITE option and related code
2.Broadcast the readability to all reader and poller
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
-The qemu wifi fucntion only supports the STA mode and the following
operations:
wapi mode wlan0 2
wapi scan wlan0
wapi psk wlan0 password 3
wapi essid wlan0 wifi_name 1
wapi show wlan0
wapi disconnect wlan0
-Eanble the virtual wifi function with the MACRO `CONFIG_DRIVERS_WIFI_SIM`.
Signed-off-by: liqinhui <liqinhui@xiaomi.com>
Refers to https://docs.oasis-open.org/virtio/virtio/v1.2/cs01/virtio-v1.2-cs01.html#x1-2230004
A driver SHOULD negotiate VIRTIO_NET_F_MAC if the device offers it.
If the driver negotiates the VIRTIO_NET_F_MAC feature, the driver MUST
set the physical address of the NIC to mac. Otherwise, it SHOULD use a
locally-administered MAC address.
Signed-off-by: liqinhui <liqinhui@xiaomi.com>
Commit 8a63d29c removed `devif_iob_send` from `udp_sendto_buffered`
workflow, `devif_iob_send` drops too big packet. Now we still need a
place to check the packet length, otherwise a packet larger than MTU
may be sent to the net driver.
In case of similar problem happens somewhere else, this commit also
adds a check in `netdev_upperhalf`, and count these cases into
`NETDEV_TXERRORS`.
Signed-off-by: Zhe Weng <wengzhe@xiaomi.com>
Busy waiting in w25qxxxjv_erase_sector() was without nxsig_usleep and
was causing the entire system to freeze for significant amount of time
as sector erase takes some time.
This commit adds nxsig_usleep into busy waiting to prevent system lock.
Sleep is set to sector erase time based on W25Q series datasheet.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
we can use uart to debug nuttx,like debugger:
1. read/write memory
2. Use watchpoint,breakpoint,single step.
use up_debugpoint api
3. Ctrl+c to stop, continue, or single step.
hold uart send and receive
4. register a panic event, when crash or assert/panic, we use uart to
debug.
Signed-off-by: anjiahao <anjiahao@xiaomi.com>
Add registration function instrumentation API,
which can achieve instrumentation of entering and
exiting functions through the compiler's functionality.
We can use CONFIG_ARCH_INSTRUMENT_ALL to add instrumentation for all
source, or add '-finstrument-functions' to CFLAGS for Part of the
source.
Notice:
1. use CONFIG_ARCH_INSTRUMENT_ALL must mark _start or entry noinstrument_function,
becuase bss not set.
2. Make sure your callbacks are not instrumented recursively.
use instrument_register to register entry function and exit function.
They will be called by the instrumented function
Signed-off-by: anjiahao <anjiahao@xiaomi.com>
Previously CONFIG_USBDEV_SOFINTERRUPT existed in many platform
drivers but did nothing. This commit adds a callback function
usbdev_sof_irq() that can be used to take action on this interrupt.
To avoid losing the first frame, the set_buf needs to excute first. At the same time, imgdata->start_capture should excuted before the imgsensor->start_capture.
Signed-off-by: yaojingwei <yaojingwei@xiaomi.com>
The driver's main purpose is to support the porting of the open source
component optee_client (https://github.com/OP-TEE/optee_client) to nttux.
The basic function of the driver module is to convert the REE application layer data and send it to the TEE through rpmsg.
The main functions include
1 driver registration.
we need to register a device driver(/dev/tee0) through optee_register function.
2 open the driver
3 ioctl the driver
The ioctl command passes different parameters and commands, and interacts with the TEE through rpmsg.
4 close the driver
Signed-off-by: hujun5 <hujun5@xiaomi.com>
It may cause out_of_bounds when two side have different configuartion
on NAME_MAX and FS_LARGEFILE(affects size of blkcnt_t)
Signed-off-by: liaoao <liaoao@xiaomi.com>
it may cause use after free if server has removed block device before calling
its operations,such as:
server: rm /dev/testrpmsgblk
client: ls /dev/testrpmsgblk
Signed-off-by: liaoao <liaoao@xiaomi.com>
A segmentfault might happen when read/write/unlink ops called without an open
ops called because it bind ept's ops in rpmsgblk_open_handler.
proxy> rm /dev/ram1
segmentfault
proxy> ls /dev/ram1
segmentfault
Signed-off-by: liaoao <liaoao@xiaomi.com>
There are ICs available on the market that integrate various power inverter
features. The driver for such a device must be tightly coupled to a FOC device
as using it as a separate device doesn't make sense.
