arch/arm/src/stm32/stm32_adc.c: refactor adc_reset. It should be easier to maintain this code if it's divided into smaller functions
Approved-by: GregoryN <gnutt@nuttx.org>
Use STM32 DMA IP core version instead of chip family names and some minor improvements
arch/arm/src/stm32/chip/stm32_adc.h: raise error if two IP cores seleceted
libs/libdsp/Kconfig: cosmetic change
arch/arm/src/stm32/Kconfig: hide TIMER menu, HRTIM menu and USB Host debug menu if peripherals not enabled
configs/stm32f429i-disco/highpri/defconfig: fix configuration warning
Approved-by: GregoryN <gnutt@nuttx.org>
configs/nucleo-f207zg, configs/nucleo-f103rb: add ADC and PWM examples; arch/arm/src/stm32_adc.c: there is no DMA CFG bit for the basic IPv1 ADC
Approved-by: GregoryN <gnutt@nuttx.org>
Improvements in STM32 ADC, minor changes in STM32 PWM, DMA, HRTIM and add some highpri ADC examples
arch/arch/src/stm32/stm32_adc: fix RCC reset logic
arch/arch/src/stm32/stm32_adc: move sample time change functions to low-level ADC ops
arch/arch/src/stm32/stm32_adc: configurable ADC DMA mode (one shot mode, circular mode)
arch/arch/src/stm32/stm32_pwm: remove llops_get interface. We can use structure casting to get pwm low-level ops
arch/arch/src/stm32/stm32_pwm: add timer enable/disable and frequency update to low-level ops
arch/src/arm/stm32: remove redundant stm32f33xxx_dma.c
arch/arm/src/stm32/stm32f40xxx_dma.c: add interfaces to interact with highp priority DMA interupts
arch/src/arm/stm32/stm32_hrtim: do not enable timers on startup if option from Kconfig selected and add interface to enable/disable timers
arch/src/arm/stm32/stm32_hrtim: fix some warnings
configs/nucleo-f334r8/highpri: update configuration due to changes in stm32_adc
configs/stm32f334-disco/buckboost: update configuration due to changes in stm32_adc
configs/nucleo-f334r8/highpri: add support for ADC injected sequence, add triggering from TIM1
configs/nucleo-f302r8/highpri: add high priority ADC interrupts example
configs/stm32f429i-disco/highpri: add high priority ADC interrupts example
Approved-by: GregoryN <gnutt@nuttx.org>
stm32/stm32_adc: major refator
stm32/stm32_adc: use STM32 ADC IP core version and ADC available functions instead of chip family names in conditional compilation
stm32/chip: replace family specific ADC headers with STM32 ADC IP core version headers
stm32/stm32_adc: configurable sample time supported for all chips, not only L1
stm32/stm32_adc: enable/disable interrupts supported for all chips, not only L1
stm32/stm32_adc: resolution configuration
stm32/stm32f33xxx_adc: remove wrong assertion
configs/nucleo-f303ze: support for ADC and ADC example
configs/stm32f429i-disco: support for ADC and ADC example
Approved-by: GregoryN <gnutt@nuttx.org>
This change is needed specifically for the case where a bootloader sets the SPE bit before starting NuttX. In that case, the test in the SPI driver is bogus. This change fixes that by assuring that NuttX has booted and initialized at least once (whether or not SPE is set) before the driver starts refusing to initialize.
arch/arm/stm32*: Don't rely on SPI_CR1_SPE to determine if peripheral has been initialized yet.
Approved-by: GregoryN <gnutt@nuttx.org>
Fixes Kconfig options to include all STM32F20XX processors, not just STM32F207
* arch/arm/src/stm32: Fixes Kconfig options to include all STM32F20XX processors, not just STM32F207
* arch/arm/src/stm32: Removes redundant STM32_STM32F429 depends from Kconfig. STM32F4XXX already does this
Approved-by: GregoryN <gnutt@nuttx.org>
Improvements in STM32 PWM low level driver
stm32_pwm: remove some impossible PWM configurations
stm32_pwm: support for complementary outputs
stm32_pwm: deadtime configuration
stm32_pwm: output polarity and IDLE state configuration
nucleo-f302r8: pwm support
stm32f429i-disco: pwm support
configs: update some configurations according to changes in STM32 PWM driver
Approved-by: GregoryN <gnutt@nuttx.org>
Pull request for mtd/progmem refactoring.
* mtd/progmem: change up_progmem_npages to up_progmem_neraseblocks
page is a unit for read/write operation.
eraseblock is a unit for erase operation.
up_progmem_npages is a little bit confusing because it returns number of
erase blocks in flash memory. This patch changes up_progmem_npages to
up_progmem_neraseblocks. There is no logical change.
Signed-off-by: EunBong Song <eunb.song@samsung.com>
* mtd/progmem: up_progmem_erasesize.
Change argument name to be more readable.
Signed-off-by: EunBong Song <eunb.song@samsung.com>
* mtd/progmem: up_progmem_eraseblock
Change up_progmem_erasepage to up_progmem_eraseblock.
eraseblock is more readable name than erasepage.
Signed-off-by: EunBong Song <eunb.song@samsung.com>
* mtd/progmem: change up_progmem_eraseblock's return value.
up_progmem_eraseblock erase a block. so it's better to return the erase block
size than page size.
Signed-off-by: EunBong Song <eunb.song@samsung.com>
* arm/cortex-r : fix wrong cp15_flash_dcache.
change mcrne to mcr for unconditional dcache.
Signed-off-by: sungduk.cho <sungduk.cho@samsung.com>
Approved-by: GregoryN <gnutt@nuttx.org>
While this is a good idea and a proper thing to do, it also creates a circular dependency and errors during configuration. RTC depends on STM32_RTC which depends on RTC_EXTERNAL with depends on RTC. No can do.
This reverts commit 714e8c1f9e.
