./build.sh sim:usbdev -j12
sudo gdb nuttx/nuttx -ex "source nuttx/tools/gdb/__init__.py"
below command to create mbim NIC on host
nsh> conn 3
NuttX's MBIM device implementation adds an additional MBIM network
card to the NuttX system, which can debug the data communication with
the host, but this network card is unnecessary and needs to be removed
when the business actually uses this driver, And the cdcncm_receive
method needs to be re-implemented.
Signed-off-by: zhanghongyu <zhanghongyu@xiaomi.com>
Adds support for timestamping received UDP packets, either in
hardware or in kernel. Builds on the existing support of SO_TIMESTAMP
for SocketCAN.
Implementation uses CLOCK_REALTIME for timestamping to match the
behavior of Linux. This could be made configurable in future if needed.
There're some apps trying to set too large SO_SNDBUF and SO_RCVBUF, which may use all IOBs in one socket and block all other network traffic.
Note:
Linux silently limits SO_SNDBUF to be less than `sysctl_wmem_max`, so we can also do this limit without returning any error.
Signed-off-by: Zhe Weng <wengzhe@xiaomi.com>
This is a refactored version of the SLIP network driver. Updates
include:
1. The original design started two kernel threads per SLIP device.
The refactored version uses file_poll to essentially be driven
by the UART RX and TX interrupts and pushes work to the low
priority work queue.
2. The SLIP byte un-/stuffing is more efficient now, using memcpy
instead of handling each byte individually.
3. The switch of the old SLIP driver to IOBs caused buffer overwrites
if packets were sent that would not fit into a single IOB. This is
fixed now.
Signed-off-by: Michael Jung <michael.jung@secore.ly>
Timestamp location in can message has changed,
In the original logic timestamp is saved at the end of the data segment:
io_data
-------------------------------------------------
| CAN message | Time Stamp |
-------------------------------------------------
|<--------------- io_len ---------------->|
In the new structure timestamps will reuse NET_LL_GUARDSIZE to isolate CAN messages:
io_data io_offset
-------------------------------------------------
| Time Stamp | CAN message |
-------------------------------------------------
|<-------- io_len --------->|
This PR will:
1. Increase NET_LL_GUARDSIZE to 16 (sizeof(struct timeval)) if NET_CAN && NET_TIMESTAMP are enabled
2. Apply timestamp to adapt to the new structure
Signed-off-by: chao an <anchao@xiaomi.com>
Add basic functions for NAT (NAPT), remaining some logic unimplemented (UDP, ICMP, port assignment, etc). NAT for TCP can work now (unless port conflicts).
Outbound: LAN -> Forward -> NAT(only if targeting at WAN) -> WAN
Inbound: WAN -> NAT(only from WAN, change dest) -> Forward -> LAN
Signed-off-by: Zhe Weng <wengzhe@xiaomi.com>
1.Add cellular link layer enum definition and register flow
2.Add ioctl flow to set cellular NICs parameters
Signed-off-by: luojun1 <luojun1@xiaomi.com>
Signed-off-by: chao an <anchao@xiaomi.com>
add config CONFIG_NET_ALLOC_CONNS to support allocate connect.
Use this feature if the number of connections can not be determined at
compile time. When enabled the stack will be compiled without the static
pre-allocate connection list and all connection instances will be dynamically
allocated from heap at run time.
Signed-off-by: chao.an <anchao@xiaomi.com>
so netdb could reuse these global variable directly
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: Iaa26ddbdaf416f64d43c6e8888a14bbe0c3405eb
* The appropriate size of stack varies among archs.
E.g. for 64-bit sim, 2048 is way too small, especially when the task
happens to use host OS functionalities.
I plan to allow an arch provide its own default.
* I plan to use this to replace hardcoded "STACKSIZE = 2048" in APPDIR.
Historically, the loopback driver used the largest packet size of all enabled link layer protocols. This permitted packets to be forward via the loopbak device with no major loss of performance. However, in experimenting with configurations where no other link layer protocols were enabled, this means the loopback packet size was set to the smallest possible size, to the SLIP minimum of 296 bytes. This resulted in terrible loopback performance.
This commit adds an option to increase the loopback packet size with the option CONFIG_NET_LOOPBACK_PACKETSIZE.
The loopback driver packet buffer should be quite large. The larger the loopback packet buffer, the better will be TCP performance of the loopback transfers. The Linux loopback device historically used packet buffers of size 16Kb, but that was increased in recent Linux versions to 64Kb. Those sizes may be excessive for resource constrained MCUs, however.
The network still enforces the lower limit that is the maximum packet size of all enabled link layer protocols. But this new option permits the loopback packet size to be increased from that.
* net/Kconfig: Adds CONFIG_NET_LOOPBACK_PKTSIZE option
* include/nuttx/net/netconfig.h: Assures that the packet size that is used is at least as large as the largest packet size of other link layer protocols.
* drivers/net/loopback.c: Use that larger packet size.
* boards/sim/sim/sim/configs/tcploop/defconfig: Set the loopback packet size to 1500
Here is the email loop talk about why it is better to remove the option:
https://groups.google.com/forum/#!topic/nuttx/AaNkS7oU6R0
Change-Id: Ib66c037752149ad4b2787ef447f966c77aa12aad
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
