Summory
This Power State Coordination Interface (PSCI) defines a standard
interface for power management. the PCSI need to implement handling
firmware at EL2 or EL3 for ARM64. the PSCI maybe not applicable
for arm core without PCSI firmware interface implement.
Add configure option for it.
Note:
1. ostest is PASSED at qemu and fvp ( single core and SMP)
Signed-off-by: qinwei1 <qinwei1@xiaomi.com>
The function is not relevant any longer, remove it. Also remove
save_addrenv_t, the parameter taken by up_addrenv_restore.
Implement addrenv_select() / addrenv_restore() to handle the temporary
instantiation of address environments, e.g. when a process is being
created.
Summary:
1. to enable Toolchain select Kconfig option, making something depend on
the opton to be configured with menuconfig
Signed-off-by: qinwei1 <qinwei1@xiaomi.com>
This is preparation for moving address environments out of the group
structure into the tcb.
Why move ? Because the group is destroyed very early in the exit phase,
but the MMU mappings are needed until the context switch to the next
process is complete. Otherwise the MMU will lose its mappings and the
system will crash.
There were two issues with signal handling:
- With a kernel stack the "info" parameter was passed from kernel memory.
This is fixed by making a stack frame to the user stack and copying it
there.
- If the signal handler uses a system call, the kernel stack was completely
and unconditionally destroyed, resulting in a crash in the user application
There is also no need to check ustkptr, it is always NULL. Why ? Because
signal delivery is deferred when a system call is being executed.
The dependency should be vice versa; the MM_SHM should depend on the
existence of the virtual memory range allocator.
Create a new CONFIG flag CONFIG_ARCH_VMA_MAPPING, which will define that
there is a virtual memory range allocator. Make MM_SHM select that flag
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
The current implementation of PIO Interrupt for Allwinner A64 is incomplete. This PR fixes the implementation of PIO Interrupt for all supported PIO Ports (PB, PG and PH).
### Modified Files
`arch/arm64/src/a64/a64_pio.c`, `a64_pio.h`: Add implementation of PIO Interrupt
`arch/arm64/include/a64/irq.h`: Add IRQ for PIO Port PH
`arch/arm64/src/a64/hardware/a64_pio.h`: Fix addresses of PIO Interrupt Registers
This PR adds the driver for Xingbangda XBD599 LCD Panel (based on Sitronix ST7703 LCD Controller) on PINE64 PinePhone. This PR also includes:
- The driver for X-Powers AXP803 Power Mgmt IC, which calls our driver for Allwinner A64's Reduced Serial Bus. The PMIC Driver is needed to power on the MIPI DSI Interface for the LCD Panel.
- A simple Display Driver that renders a Test Pattern on the LCD Display at startup. It calls our Allwinner A64 drivers for Display Engine, Timing Controller TCON0 and MIPI Display Serial Interface.
The NuttX Frame Buffer Driver will be implemented in the next PR.
`arch/arm64/src/a64/a64_de.c`, `a64_de.h`: Changed the Frame Buffer pointer to `const` for Allwinner A64 Display Engine
`arch/arm64/src/a64/hardware/a64_memorymap.h`: Added the Base Address for PWM, for controlling the PWM Backlight
`boards/arm64/a64/pinephone/src/pinephone_bringup.c`: Call `fb_register()` to start the Display Driver at startup
`boards/arm64/a64/pinephone/src/Makefile`: Added LCD Driver, PMIC Driver and Display Driver to Makefile
`boards/arm64/a64/pinephone/Kconfig`: Added the Kconfig option for "PINE64 PinePhone > LCD Display" (`CONFIG_PINEPHONE_LCD`) which enables the LCD Driver, PMIC Driver and Display Driver
`boards/arm64/a64/pinephone/src/pinephone_lcd.c`, `pinephone_lcd.h`: Driver for Xingbangda XBD599 LCD Panel
`boards/arm64/a64/pinephone/src/pinephone_pmic.c`, `pinephone_pmic.h`: Driver for X-Powers AXP803 Power Mgmt IC
`boards/arm64/a64/pinephone/src/pinephone_display.c`: Simple Display Driver that renders a Test Pattern in `up_fbinitialize()`
`boards/arm64/a64/pinephone/configs/lcd/defconfig`: New PinePhone Board Configuration `pinephone:lcd` that enables the LCD Driver (`CONFIG_PINEPHONE_LCD`)
`platforms/arm/a64/boards/pinephone/index.rst`: Added PinePhone Board Configuration `pinephone:lcd` that enables the LCD Driver
This PR adds the driver for Reduced Serial Bus (RSB) on Allwinner A64 SoC. The RSB Driver will be called by the upcoming Power Mgmt IC Driver for PINE64 PinePhone, to power on the LCD Display.
`arch/arm64/src/a64/Kconfig`: Added the Kconfig option for "A64 Peripheral Selection > RSB" (`CONFIG_A64_RSB`), which enables the RSB Driver
`arch/arm64/src/a64/hardware/a64_memorymap.h`: Added the Base Address for RSB
`arch/arm64/src/a64/Make.defs`: Added the RSB Driver to the Makefile
`arch/arm64/src/a64/a64_de.c`: Increase PLL Timeout for Allwinner A64 Display Engine
`boards/arm64/a64/pinephone/configs/nsh/defconfig`: Set PinePhone Board Config `CONFIG_BOARD_LOOPSPERMSEC` to the value computed by `calib_udelay`
`arch/arm64/src/a64/a64_rsb.c`, `a64_rsb.h`: RSB Driver for Allwinner A64
`platforms/arm/a64/boards/pinephone/index.rst`: Added RSB as supported peripheral for PinePhone
This PR adds the driver for Display Engine 2.0 on Allwinner A64 SoC. The Display Engine Driver will be called by the upcoming LCD Driver for PINE64 PinePhone.
`arch/arm64/src/a64/Kconfig`: Added the Kconfig option for "A64 Peripheral Selection > DE" (`CONFIG_A64_DE`), which enables the Display Engine Driver
`arch/arm64/src/a64/hardware/a64_memorymap.h`: Added the Base Address for Display Engine
`arch/arm64/src/a64/Make.defs`: Added the Display Engine Driver to the Makefile
`boards/arm64/a64/pinephone/configs/nsh/defconfig`: Removed Scheduler Debug Info (`CONFIG_DEBUG_SCHED_INFO`) from the PinePhone Board Config, because it garbles the Console Output.
`arch/arm64/src/a64/a64_de.c`, `a64_de.h`: Display Engine Driver for Allwinner A64
`platforms/arm/a64/boards/pinephone/index.rst`: Added Display Engine as supported peripheral for PinePhone
This PR adds the driver for TCON0 (Timing Controller) on Allwinner A64 SoC. The TCON0 Driver will be used by the upcoming Display Driver for PINE64 PinePhone.
`arch/arm64/src/a64/Kconfig`: Added the Kconfig option for "A64 Peripheral Selection > TCON0" (`CONFIG_A64_TCON0`), which enables the TCON0 Driver
`arch/arm64/src/a64/hardware/a64_memorymap.h`: Added the Base Address for TCON0
`arch/arm64/src/a64/Make.defs`: Added the TCON0 Driver to the Makefile
`arch/arm64/src/a64/a64_tcon0.c`, `a64_tcon0.h`: TCON0 Driver for Allwinner A64
`platforms/arm/a64/boards/pinephone/index.rst`: Added TCON0 as supported peripheral for PinePhone
This PR adds the driver for Allwinner A64's MIPI Display Serial Interface (DSI) and MIPI Display Physical Layer (D-PHY).
This driver will be used by the upcoming Display Driver for PINE64 PinePhone.
- `include/nuttx/crc16.h`: Added 16-bit CRC-CCITT
- `libs/libc/misc/Make.defs`: Added 16-bit CRC-CCITT to Makefile
- `arch/arm64/src/a64/Kconfig`: Added the Kconfig option for "A64 Peripheral Selection > MIPI DSI" (`CONFIG_A64_MIPI_DSI`), which enables the MIPI DSI Driver
- `arch/arm64/src/a64/hardware/a64_memorymap.h`: Added the Base Address for MIPI DSI
- `arch/arm64/src/a64/Make.defs`: Added the MIPI DSI Driver to the Makefile
- `libs/libc/misc/lib_crc16ccitt.c`: Compute 16-bit CRC-CCITT
- `arch/arm64/src/a64/mipi_dsi.c`, `mipi_dsi.h`: Compose MIPI DSI Packets (Long, Short, Short with Parameter)
- `arch/arm64/src/a64/a64_mipi_dsi.c`, `a64_mipi_dsi.h`: MIPI DSI Driver for Allwinner A64
- `arch/arm64/src/a64/a64_mipi_dphy.c`, `a64_mipi_dphy.h`: MIPI D-PHY Driver for Allwinner A64
- `platforms/arm/a64/boards/pinephone/index.rst`: Added MIPI DSI as supported peripheral for PinePhone
Co-Authored-By: Petro Karashchenko <petro.karashchenko@gmail.com>
Registers S0-S15 (D0-D7, Q0-Q3) do not need to be preserved. They can be used for passing
arguments or returning results in standard procedure-call variants.
Registers D16-D31 (Q8-Q15), do not need to be preserved.
Signed-off-by: zhangyuan21 <zhangyuan21@xiaomi.com>
This PR adds the drivers for Allwinner A64 PIO (Programmable I/O) and PinePhone LEDs (Red / Green / Blue).
The PIO Driver is based on the NuttX PIO Driver for Allwinner A10: [`arch/arm/src/a1x/a1x_pio.c`](https://github.com/apache/nuttx/blob/master/arch/arm/src/a1x/a1x_pio.c)
- `arch/arm64/src/a64/Make.defs`: Add PIO Driver to Makefile
- `boards/Kconfig`: Add `ARCH_HAVE_LEDS` to PinePhone
- `boards/arm64/a64/pinephone/src/pinephone.h`: Define PinePhone LEDs
- `boards/arm64/a64/pinephone/src/pinephone_boardinit.c`: Start Auto LEDs
- `boards/arm64/a64/pinephone/src/pinephone_bringup.c`: Start User LEDs
- `boards/arm64/a64/pinephone/src/Makefile`: Add LED Driver to Makefile
- `boards/arm64/a64/pinephone/configs/nsh/defconfig`: Add `CONFIG_USERLED` to `nsh` config
- `arch/arm64/src/a64/a64_pio.c`, `a64_pio.h`: Allwinner A64 PIO Driver
- `arch/arm64/src/a64/hardware/a64_memorymap.h`: PIO Memory Map
- `arch/arm64/src/a64/hardware/a64_pio.h`: PIO Definitions
- `boards/arm64/a64/pinephone/include/board.h`: Define PinePhone LEDs
- `boards/arm64/a64/pinephone/src/pinephone_autoleds.c`: Driver for Auto LEDs
- `boards/arm64/a64/pinephone/src/pinephone_userleds.c`: Driver for User LEDs
- `introduction/supported_platforms.rst`: Add Allwinner A64 as Supported Platform
- `platforms/arm/a64/boards/pinephone/index.rst`: Add PIO and LEDs to PinePhone
Summary:
- I noticed that the nsh prompt can not be shown when disabling
debug features. Actually, the prompt will be shown when a user
input happens.
- This commit fixes this issue by adding uart_xmitchars() as
other serial drivers do.
Impact:
- None
Testing:
- Tested with qemu-armv8a:netnsh on QEMU-7.1
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
It takes about 10 cycles to obtain the task list according to the task
status. In most cases, we know the task status, so we can directly
add the task from the specified task list to reduce time consuming.
It takes about 10 cycles to obtain the task list according to the task
status. In most cases, we know the task status, so we can directly
delete the task from the specified task list to reduce time consuming.
Currently NuttX on Arm64 supports Generic Interrupt Controller (GIC) Versions 3 and 4: [`arm64_gicv3.c`](https://github.com/apache/incubator-nuttx/blob/master/arch/arm64/src/common/arm64_gicv3.c), [`arm64_gic.h`](https://github.com/apache/incubator-nuttx/blob/master/arch/arm64/src/common/arm64_gic.h). This PR adds support for GIC Version 2, which is needed by [Pine64 PinePhone](https://lupyuen.github.io/articles/interrupt) based on Allwinner A64 SoC.
This 64-bit implementation of GIC v2 is mostly identical to the existing GIC v2 for 32-bit Armv7-A ([`armv7-a/arm_gicv2.c`](https://github.com/apache/incubator-nuttx/blob/master/arch/arm/src/armv7-a/arm_gicv2.c), [`armv7-a/gic.h`](https://github.com/apache/incubator-nuttx/blob/master/arch/arm/src/armv7-a/gic.h)), with minor modifications to support 64-bit Registers (Interrupt Context).
- `arch/arm64/Kconfig`: Under "ARM64 Options", we added an integer option `ARM_GIC_VERSION` ("GIC version") that selects the GIC Version. Valid values are 2, 3 and 4, default is 3.
- `arch/arm64/src/common/arm64_gicv2.c`: Implements 64-bit GIC v2 based on 32-bit [`armv7-a/arm_gicv2.c`](https://github.com/apache/incubator-nuttx/blob/master/arch/arm/src/armv7-a/arm_gicv2.c) and [`armv7-a/gic.h`](https://github.com/apache/incubator-nuttx/blob/master/arch/arm/src/armv7-a/gic.h), modified to support 64-bit Registers (Interrupt Context).
Function and Macro Names have not been changed, for easier cross-referencing between the 32-bit and 64-bit implementations of GIC v2.
- `arch/arm64/src/common/arm64_gicv3.c`: Added Conditional Compilation for GIC v3. This file will not be compiled if `ARM_GIC_VERSION` is 2.
- `arch/arm64/src/common/arm64_gic.h`: Added the Version Identifier for GIC v2. At startup we read the GIC Version from hardware and verify that it matches `ARM_GIC_VERSION`.
- `arch/arm64/include/qemu/chip.h`: Added the QEMU Base Addresses for GIC v2.
- `arch/arm64/src/common/Make.defs`: Added the source file that implements GIC v2.
- `boards/arm64/qemu/qemu-armv8a/README.txt`: Added the documentation for testing GIC v2 with QEMU.
- `boards/arm64/qemu/qemu-armv8a/configs/nsh_gicv2/defconfig`: Added the Board Configuration `qemu-armv8a:nsh_gicv2` for testing GIC v2 with QEMU. Identical to `qemu-armv8a:nsh`, except that `ARM_GIC_VERSION` is 2.
In the past, header file paths were generated by the incdir command
Now they are generated by concatenating environment variables
In this way, when executing makefile, no shell command will be executed,
it will improve the speed of executing makfile
Signed-off-by: yinshengkai <yinshengkai@xiaomi.com>
This change adds the following:
- Rename the board configuration name from qemu-a53 to qemu-v8a.
- Add the configurations for Cortex-A57 and Cortex-A72.
Signed-off-by: Hidenori Matsubayashi <hidenori.matsubayashi@gmail.com>
Use CONFIG_ARCH_CHIP_QEMU instead of CONFIG_ARCH_CHIP_QEMU_A53. This is because these configurations depend on the hardware configuration of qemu (memory map, irq numbers, etc.).
Signed-off-by: Hidenori Matsubayashi <hidenori.matsubayashi@gmail.com>
