Commit 50a8ec6 broke many mmc devices. Only if the flag
priv->caps & SDIO_CAPS_4BIT_ONLY was set, it migth work.
Without the flag, the mmc clock is never set (mmcsd_widebus()
call is terminated early stopping the clock). This flag
is probably not very generic because most mmc hw support
1, 4 and 8 bit modes.
JEDEC specifies a bus width selection procedure, but it's
not implemented in this mmcsd_sdio.c driver. Thus, it's
not known whether the hw supports 1, 4 anf 8 bit modes or
a combination of them.
However, with priv->caps & SDIO_CAPS_4BIT_ONLY the driver
suddenly assigns priv->buswidth = MMCSD_SCR_BUSWIDTH_4BIT
making it the only way to have the driver working.
Fix this by relaxing the above mentioned restrictions.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Some hardware needs to config this delay to write one data block, because
the hardware needs more time to wear leveling and bad block manage.
Signed-off-by: dongjiuzhu1 <dongjiuzhu1@xiaomi.com>
1. Update all CMakeLists.txt to adapt to new layout
2. Fix cmake build break
3. Update all new file license
4. Fully compatible with current compilation environment(use configure.sh or cmake as you choose)
------------------
How to test
From within nuttx/. Configure:
cmake -B build -DBOARD_CONFIG=sim/nsh -GNinja
cmake -B build -DBOARD_CONFIG=sim:nsh -GNinja
cmake -B build -DBOARD_CONFIG=sabre-6quad/smp -GNinja
cmake -B build -DBOARD_CONFIG=lm3s6965-ek/qemu-flat -GNinja
(or full path in custom board) :
cmake -B build -DBOARD_CONFIG=$PWD/boards/sim/sim/sim/configs/nsh -GNinja
This uses ninja generator (install with sudo apt install ninja-build). To build:
$ cmake --build build
menuconfig:
$ cmake --build build -t menuconfig
--------------------------
2. cmake/build: reformat the cmake style by cmake-format
https://github.com/cheshirekow/cmake_format
$ pip install cmakelang
$ for i in `find -name CMakeLists.txt`;do cmake-format $i -o $i;done
$ for i in `find -name *\.cmake`;do cmake-format $i -o $i;done
Co-authored-by: Matias N <matias@protobits.dev>
Signed-off-by: chao an <anchao@xiaomi.com>
- Fix DMA addressing issues within litex_sendsetup/litex_recvsetup
- Extend with handling specific to eMMC commands during init & use.
- Cleanup of 4-bit BUS handling for SD and eMMC
- For eMMC, Send CMD0 during init as per JEDEC v4.41 for pre-idle
MMC_CMD1 command is used to check whether card is MMC type (checked if
CONFIG_MMCSD_MMCSUPPORT is enabled). This commit inserts nxsig_usleep
wait if this check fails. This is to ensure the communication recovers
from invalid response as this may take some time on some platforms (
samv7 for example). Following command for SDHC check may fail if sleep
is not used.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
mmcsd_removed will be called if the card is in invalid state.
This can happen if the card is bad, or vibrations causes a power
loss.
mmcsd_removed resets:
priv->capacity = 0; /* Capacity=0 sometimes means no media */
priv->blocksize = 0;
priv->probed = false;
priv->mediachanged = false;
priv->wrbusy = false;
priv->type = MMCSD_CARDTYPE_UNKNOWN;
priv->rca = 0;
priv->selblocklen = 0;
priv->widebus = false;
If blocksize is set to 0 will cause the log2 to result
in an infinate loop in some drivers.
IS_EMPTY will check for priv->type = MMCSD_CARDTYPE_UNKNOWN
and return ENODEV.
In the past, header file paths were generated by the incdir command
Now they are generated by concatenating environment variables
In this way, when executing makefile, no shell command will be executed,
it will improve the speed of executing makfile
Signed-off-by: yinshengkai <yinshengkai@xiaomi.com>
1.Don't check the return value of nxsem_init or nxmutex_init
2.Fix some style issue
Signed-off-by: anjiahao <anjiahao@xiaomi.com>
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
since rwbuffer isn't fully initiailized in mmcsd_slotinitialize.
BTW, if the cache is important for performance, it is better to
implement a general block cache and put in a common location.
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
