The bc022f8cd8 introduces a static way to calculate idle stack
address for risc-v platform. However, it uses the reverse order
to access idle stack, which breaks boards with smp configuration.
Correct the idle stack order of g_cpux_idlestack.
Fixes: bc022f8cd8 ("arch/risc-v: unify idle stack calculation")
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
As all the board allocate idle stack from _ebss. The idle stack
layout is fix and can be computed directly by using _ebss. There
is no need to use g_cpux_idlestack array anymore, remove it.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
As the stack layout is unified, it is possible to
use a unify formula to calculate the top of idle
stack.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
chip/s698pm_cpustart.c: In function 's698pm_cpu_boot':
Error: chip/s698pm_cpustart.c:74:17: error: unused variable 'tcb' [-Werror=unused-variable]
struct tcb_s *tcb = this_task();
^~~
cc1: all warnings being treated as errors
make[1]: *** [Makefile:99: s698pm_cpustart.o] Error 1
make[1]: Target 'libarch.a' not remade because of errors.
make: *** [tools/LibTargets.mk:164: arch/sparc/src/libarch.a] Error 2
make: Target 'all' not remade because of errors.
/github/workspace/sources/nuttx/tools/testbuild.sh: line 370: /github/workspace/sources/nuttx/../nuttx/nuttx.manifest: No such file or directory
Normalize s698pm-dkit/smp
Signed-off-by: hujun5 <hujun5@xiaomi.com>
Make channels synchronous (i.e. share the same timebase) with the help
of SAMV7_PWMx_CHy_SYNC defines. All the channels share the same
timebase of channel 0, so this channel must be defined too.
Signed-off-by: Stepan Pressl <pressste@fel.cvut.cz>
ESP32 SoC use a static allocated array as idle stack. To fit
the existed idle stack allocation, make idle stack allocated
from ebss for the whole esp32 series.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Optimal size of granule is 64B (the dcache line size).
We can use it now as we don't have max. 32 granules limitation anymore.
Signed-off-by: Jani Paalijarvi <jani.paalijarvi@unikie.com>
This adds SBI specfication v0.3 based `riscv_sbi_system_reset()` to
support SBI firmware based system reset in kernel mode.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
1. Adjust code to avoid PM wakelock->count less than or equal to 0.
2. Fix some document format issues.
Signed-off-by: chenwen@espressif.com <chenwen@espressif.com>
Although almost all board support allocating idle stack after ebss,
bl602 have a different memory layout for idle stack. To unify them,
make idle stack allocated from ebss for bl602.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
NuttSBI have a simple ecall interface for the kernel, which make
it hard to add new SBI call for NuttSBI. So implement standard
ecall interface for NuttSBI and make life easier.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
With CONFIG_MMCSD_MULTIBLOCK_LIMIT not set. (No limit)
The DMA driver would overwrite the internal buffer.
By adding CONFIG_ARCH_HAVE_SDIO_PREFLIGHT and
CONFIG_FAT_DMAMEMORY we can insure alignment and
maximize performance using no CONFIG_MMCSD_MULTIBLOCK_LIMIT
Using user allocated buffers for DMA transfers is not safe for two reasons:
- User space memory is virtual memory, DMA needs physical memory
- User memory buffer alignment cannot be guaranteed -> cache line ops
are not safe
Add a simple allocator for DMA safe memory. It will provide contiguous
blocks of memory with D-Cache line size alignment.
NOTE: The optimal granule size is the D-Cache line size (64), but due
to restrictions in the granule allocator this would result in a maximum
block size of 2K only, thus use 256B granules instead givin 8K max block
size.
Once the granule allocator is fixed this limitation can be removed.
Option CONFIG_SENSORS_QENCODER might be configured even if SAMv7 qencoder
over timer counter is not used (for example encoder over GPIO is selected
with CONFIG_SAMV7_GPIO_ENC). This can cause compile warnings, also build
of sam_qencoder.c file is unnecessary in that case.
New hidden option CONFIG_SAMV7_QENCODER is added and automatically
selected if at least one timer counter is enabled for qencoder. Build
is triggered on this option.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
PWMx_CHy_LONLY options have been added to Kconfig, too.
If LONLY is selected, it's not possible to use complementary outputs.
If LONLY is not selected, it's possible to use H or complementary
output. If configured correctly with cpol and dcpol attributes,
a H-like behaviour can be achieved. May be useful when you run out
of free MCU pins.
Signed-off-by: Stepan Pressl <pressste@fel.cvut.cz>
The qemu-rv use a small init code for M mode in kernel build.
It is hard-coding and is difficult to change. Due to the fact,
introduce a already mature SBI implement (e.g OpenSBI) to
replace existing code is a better choice.
This patch introduce some change for qemu-rv:
1. use SSTC to provide time interrupt in kernel build
2. remove uncessary M mode trap.
For simplicity, this patch does not add support for booting
nuttx for any core, but force boot core to start core 0 and
let core 0 do the initialization.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
SSTC extension allows nuttx to implement S-mode timer directly,
which is useful for starting at S-mode.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
As `up_get_intstackbase` supports per cpu stack base, fix
the report value with the cpu specific one.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
It is misleading to allocate stack from static array and heap,
make all stack allocated from heap area.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
according to manual:
The FPU is not affected by any security configuration.
Thus, it appears as not present in PERIPHID[n].PERM
register located in the SPU
This patch adds definitions to support user space device mappings
that allows devices like frame buffer to be accessible from user
space in kernel mode.
The are mainly two changes:
- in `mm/`:
added vm_map_region(), vm_unmap_region() for drivers to do
device mapping easily.
- in `arch/`:
extended ARCH_SHM_NPAGES as user-space mapping region size.
decoupled ARCH_SHM_MAXREGIONS from region size calculations and
limit its usage only for SysV shm purposes.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
