Summary:
- During repeating ostest with sabre-6quad:smp (QEMU),
I noticed that pthread_rwlock_test sometimes stops
- Finally, I found that nxtask_exit() released a critical
section too early before context switching which resulted in
selecting inappropriate TCB
- This commit fixes this issue by moving nxsched_resume_scheduler()
from nxtask_exit() to up_exit() and also removing
spin_setbit() and spin_clrbit() from nxtask_exit()
because the caller holds a critical section
- To be consistent with non-SMP cases, the above changes
were done for all CPU architectures
Impact:
- This commit affects all CPU architectures regardless of SMP
Testing:
- Tested with ostest with the following configs
- sabre-6quad:smp (QEMU, dev board), sabre-6quad:nsh (QEMU)
- spresense:wifi_smp
- sim:smp, sim:ostest
- maix-bit:smp (QEMU)
- esp32-devkitc:smp (QEMU)
- lc823450-xgevk:rndis
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
In the current compilation environment, the recursive assignment(=) for compile
flags will be delayed until every file is actually need to be compile.
For example:
--------------------------------------------------------------------------------
arch/arm/src/Makefile:
INCLUDES += ${shell $(INCDIR) "$(CC)" $(ARCH_SRCDIR)$(DELIM)chip}
INCLUDES += ${shell $(INCDIR) "$(CC)" $(ARCH_SRCDIR)$(DELIM)common}
INCLUDES += ${shell $(INCDIR) "$(CC)" $(ARCH_SRCDIR)$(DELIM)$(ARCH_SUBDIR)}
INCLUDES += ${shell $(INCDIR) "$(CC)" $(TOPDIR)$(DELIM)sched}
CPPFLAGS += $(INCLUDES) $(EXTRAFLAGS)
CFLAGS += $(INCLUDES) $(EXTRAFLAGS)
CXXFLAGS += $(INCLUDES) $(EXTRAFLAGS)
AFLAGS += $(INCLUDES) $(EXTRAFLAGS)
--------------------------------------------------------------------------------
All compilation options will be included recursively,
which will be delayed until the compilation options are actually used:
tools/Config.mk:
--------------------------------------------------------------------------------
define COMPILE
@echo "CC: $1"
$(Q) $(CC) -c $(CFLAGS) $($(strip $1)_CFLAGS) $1 -o $2
endef
--------------------------------------------------------------------------------
All compile flags to be reexecuted $(INCDIR) as long as one file needs to be compiled,
but in fact, the compilation options have not changed in the current directory.
So the we recommand to change the syntax of assignment
From
Recursive (=)
To
Simple (:=)
In this way, we can ensure that all compilation options are expanded only once and reducing repeated works.
Signed-off-by: chao.an <anchao@xiaomi.com>
and remove the special handling in the stack dump
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: Ia1ef9a427bd4c7f6cee9838d0445f29cfaca3998
1.Reduce the default size of task_group_s(~512B each task)
2.Scale better between simple and complex application
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: Ia872137504fddcf64d89c48d6f0593d76d582710
to save the preserved space(1KB) and also avoid the heap overhead
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: I694073f68e1bd63960cedeea1ddec441437be025
Make.dep file should be updated by .config changed after first make.
There are 2 cases affected for this problem:
1) Add source files by config symbol
2) Include header files in #ifdef directive
These 2 cases may not be included in Make.dep and this may prevent the
differential build from working correctly.
1.It make sense to let Toolchain.defs give the default value
2.The board can still change if the default isn't suitable
3.Avoid the same definition spread more than 200 Make.defs
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: Ic2649f1c7689bcf59c105ca8db61cad45b6e0e64
since exit will be only callable from userspace and change
the 1st argument from "const uint8_t *" to "const char *"
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: I86487d57210ab63109148232da71dbc4d60a563b
ASAN trace:
...
==32087==ERROR: AddressSanitizer: heap-buffer-overflow on address 0xf4502120 at pc 0x56673ca3 bp 0xff9b6a08 sp 0xff9b69f8
WRITE of size 1 at 0xf4502120 thread T0
#0 0x56673ca2 in strcpy string/lib_strcpy.c:64
0xf4502120 is located 0 bytes to the right of 8224-byte region [0xf4500100,0xf4502120)
allocated by thread T0 here:
#0 0xf7a60f54 in malloc (/usr/lib32/libasan.so.4+0xe5f54)
#1 0x5667725d in up_create_stack sim/up_createstack.c:135
#2 0x56657ed8 in nxthread_create task/task_create.c:125
#3 0x566580bb in kthread_create task/task_create.c:297
#4 0x5665935f in work_start_highpri wqueue/kwork_hpthread.c:149
#5 0x56656f31 in nx_workqueues init/nx_bringup.c:181
#6 0x56656fc6 in nx_bringup init/nx_bringup.c:436
#7 0x56656e95 in nx_start init/nx_start.c:809
#8 0x566548d4 in main sim/up_head.c:95
#9 0xf763ae80 in __libc_start_main (/lib/i386-linux-gnu/libc.so.6+0x18e80)
CALLSTACK:
#8 0xf79de7a5 in __asan_report_store1 () from /usr/lib32/libasan.so.4
#9 0x565fd4d7 in strcpy (dest=0xf4a02121 "", src=0xf5c00895 "k") at string/lib_strcpy.c:64
#10 0x565e4eb2 in nxtask_setup_stackargs (tcb=0xf5c00810, argv=0x0) at task/task_setup.c:570
#11 0x565e50ff in nxtask_setup_arguments (tcb=0xf5c00810, name=0x5679e580 "hpwork", argv=0x0) at task/task_setup.c:714
#12 0x565e414e in nxthread_create (name=0x5679e580 "hpwork", ttype=2 '\002', priority=224, stack=0x0, stack_size=8192, entry=0x565e54e1 <work_hpthread>, argv=0x0) at task/task_create.c:143
#13 0x565e42e3 in kthread_create (name=0x5679e580 "hpwork", priority=224, stack_size=8192, entry=0x565e54e1 <work_hpthread>, argv=0x0) at task/task_create.c:297
#14 0x565e5557 in work_start_highpri () at wqueue/kwork_hpthread.c:149
#15 0x565e3e32 in nx_workqueues () at init/nx_bringup.c:181
#16 0x565e3ec7 in nx_bringup () at init/nx_bringup.c:436
#17 0x565e3d96 in nx_start () at init/nx_start.c:809
#18 0x565e3195 in main (argc=1, argv=0xffe6b954, envp=0xffe6b95c) at sim/up_head.c:95
Change-Id: I096f7952aae67d055daa737e967242eb217ef8ac
Signed-off-by: chao.an <anchao@xiaomi.com>
like other related macro(e.g. INTMAX_MIN, INTMAX_MAX...)
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: I8863599960b1a9b1c22ae9c35735a379a4c745b0
utilize the call inside nxtask_exit instead, also move
nxsched_suspend_scheduler to nxtask_exit for symmetry
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: I219fc15faf0026e452b0db3906aa40b40ac677f3
arch/z80/src/Makefile: Correct inclusion of non-existent file. This was not a problem before because there was '-' before the include. Problem revealed with '-' removed.
arch/z80/src/ez80/Toolchain.defs: Apparently there are not too many '"' in path definition.
tools/incdir.c: No space between -usrinc: or -sysinc: and the list of paths.
-Move task_init() and task_activate() prototypes from include/sched.h to include/nuttx/sched.h. These are internal OS functions and should not be exposed to the user.
-Remove references to task_init() and task_activate() from the User Manual.
-Rename task_init() to nxtask_init() since since it is an OS internal function
-Rename task_activate() to nxtask_activate since it is an OS internal function
All complaints fixed except for those that were not possible to fix:
- Used of Mixed case identifier in ESP32 files. These are references to Expressif ROM functions which are outside of the scope of NuttX.
- Remove per-thread errno from the TCB structure (pterrno)
- Remove get_errno() and set_errno() as functions. The macros are still available as stubs and will be needed in the future if we need to access the errno from a different address environment (KERNEL mode).
- Add errno value to the tls_info_s structure definitions
- Move sched/errno to libs/libc/errno. Replace old TCB access to the errno with TLS access to the errno.
So call 'make EXTRAFLAGS=-Wno-cpp' could suppress the warnings with pre-processor
directive #warning in GCC.
Change-Id: Iaa618238924c9969bf91db22117b39e6d2fc9bb6
Signed-off-by: liuhaitao <liuhaitao@xiaomi.com>
Resolution of Issue 619 will require multiple steps, this part of the first step in that resolution: Every call to nxsem_wait_uninterruptible() must handle the return value from nxsem_wait_uninterruptible properly. This commit is for all I2C drivers under arch/.
arch/z80/src/ez80/ez80_timerisr.c: Correct a mismatch between the programmed reload value and the timer input clock frequency.
arch/z80/src/ez80/ez80f92.h: Correct error in timer input clock divider: Bits 2-3, not bits 3-4.
boards/z80/ez80/z20x/src/w25_main.c: Correct an uninitialized return value; private function was not declard static.
arch/z80/src/ez80/ez80f92_init.asm: Timer control register was not being cleared and, as a result, timer interrupts may have been already enabled when the CPU was started by the debugger. This would result in spurious interrupts and Unexpected Interrupt crashes.
arch/z80/src/comming/up_initialize.c: Fix a trivial typo.
While we are at it, change the license headers in all relevant files in the affected directories to the Apache 2.0 license. Run all affected files through nxstyle.
boards/z80/ez80/z20x: Increase RX buffer size to 4Kb, reduce BAUD to 2400 in w25boot configuration
arch/z80/src/ez80/ez80_serial.c: Reduce Rx FIFO trigger level for eZ80F92 to 1 so that will respond more quickly to incoming data.
boards/z80/ez80/z20x/src/w25_main.c: Improve user interface.
There is still an error occurring while downloading Intex HEX files to FLASH. That is unrelated to this and appears to be a problem libs/libc/hex2gbin/lib_hex2bin.c
arch/z80/src/ez80/ez80_timerisr.c: Fix an error that looks the file got damaged by a bad keystroke in the editor while a string was highlighted.
boards/z80/ez80/z20x/src/ez80_spi.c: Fix some bad conditional compilationi. Prevented W25 chip select from being initialized.
Commit 797e45d6bf attempted to reduce the frequency of SPI reconfiguration by keeping track of the current frequency and mode settings and changing these settings only when the new settings differ from the old settings.
However, the original commit neglected to save the new frequency setting and, hence, was not effective in what it was trying to do: Every time the SPI setfrequency() method was called, it still looked like a new frequency and the frequency was still reconfigured, even though it hadn't really changed.
arch/z80/src/ez80/ez80_spi.c: Add logic checks to eliminate unnecessary SPI reconfiguration.
arch/z80/src/ez80/ez80_timerisr.c and arch/z80/src/ez80/ez80f92.h: Fix numerous places where configurations began with CONFIGS_ instead of CONFIG_
arch/z80/src/ez80/ez80_spi.c: Do not configure SPI chip select pin. It is not used by the driver and configuring it just clobbers other usage of that pin. Add some additional debug outputs; correct some exiting debug outputs.
drivers/mtd/w25.c: Add some debug output.
boards/z80/ez80/z20x/src/ez80_w25.c: Correct SPI bus number used in initialization. Only SPI1 is supported.
arch/z80/src/ez80/ez80_timerisr.c: Some initial timer configuration fixes.
arch/z80/: include/ez80/irq.h, src/ez80/ez80f92_*.asm: Correct some comments related to vector address offsets.
boards/z80/ez80/z20x/scripts/z20x_loader.linkcmd: Fix RAM offset in linker script
Kconfig files. Repartition some functionality. Bootloader support will need to be provided in logic under arch/z80/src/ez80 so the critical configuration selections were moved the Kconfig file there.
arch/z80/src/ez80/ez80_i2c.h: Rename arch/z80/src/ez80/ez80f91_i2c.h. It is sharable by both ez80f91 and ez80f92.
arch/z80/src/ez80/: Add logic to perform an additional level of interrupt redirection. This is necessary because the the interrupt handling is part of the loader FLASH-based logic. In order to share interrupts with the program loaded into RAM by the loader, another layer or redirection is required to get control to the interrupt handlers in the loaded program. See ez809f2_loader.asm and ez80f92_program.asm
boards/z80/ez80/z20x/scripts: Reduce size of the interrupt re-direction buffer from 1Kb to 512b.
The SD boot loader was not satisfactory because 1) the SD slot is on an optional board and, hence, cannot be part of a fundamental solution. And 2) it is too big.
The only storage on borard is the Winbond W25 SPI-bsed FLASH. This commit adds support for a bootload to 1) read code in HEX format from a serial port and write it to the W25 FLASH, or 2) read code in binary form from the W25 FLASH into SRAM and execute the loaded program.
boards/z80/ez80/z20x/configs: Added w25boot configuration
boards/z80/ez80/z20x/src: Add bootloader logic, w25_main.c. Add logic to manage shared SRAM memory map so that the loaded program does not clobber the bootloader memory. Add logic to recover the bootloader memory into the heap after the loaded program as started.
boards/z80/ez80/z20x/scripts: Rework scripts and configuration to support a bootloader and program build. The boolloader cannot use all of SRAM; the program must not clobber the SRAM region used by the bootloader.
board/z80/ez80/*/scripts/Make.defs: Fix optimization definition use in assembly flags. It was using the compiler optimization settings instead of the assembler optimization settings. Hence, enabling optimization would could cause assembler command line errors.
arch/z80/src/ez80/Toolchain.defs: Back out some work arounds. Now compiler optimization flags can again set set without assembler command line errors.
boards/z80/ez80/z20x/README.txt: Trivial update to size/optimization discussion.
The eZ80F92 interrupt controller is very different from the eZ80F91. The eZ80F91 has:
1. Four byte interrupt vectors
2. The vector base address register is 16-bit so the vector table can lie in RAM
Whereas the eZ80F92 has:
1. Two byte interrupt vectors
2. An 8-bit vector base address
This means that the vectors must lie in the first 16-bits of FLASH and there must be a "trampoline" to get to interrupt handlers outside of the first 64-Kb of FLASH.
arch/z80/src/ez80/Toolchain.defs: Correct some CFLAGS when optimization suppressed.
arch/z80/src/ez80/Kconfig arch/z80/src/ez80/ez80_emac.c: Remove configuration option for selecting EMAC RAM address. This is duplicated and possibly conflicting. The correct address for the RAM is provided in the linker command file. The RAM should be configured once and using this single definitions.
arch/z80/src/ez80/ez80_startup.asm and arch/z80/src/ez80/ez80f9*_init.asm. Move RAM and FLAH intialization out of MCU-specific logic to common start-up logic. We cannot call any functions until SRAM is initialized and the stack is properly initialized because the return address is stored on the stack. Use internal SRAM for the IDLE stack to avoid the chicken'n'egg problem.
boards/z80/ez80/z20x/configs/sdboot/sdboot.zdsproj: Discuss build environments.
These makefiles set the the ZiLOG runtime libraries for the eZ80 parts. The setup was, however, conditioned on CONFIG_ARCH_EZ80_EZ80F91 and, so, was not working for the eZ80F92 part (CONFIG_ARCH_EZ80_EZ80F92).
With this change, the z20x board FINALLY builds and links correctly with no errors.
Don't use MCU selection from compiler. It appears that we must compile ez80f92 code as ez80f91 so the comiler MCU selection is incorrect. Instead, use the selected CPU part from the configuration.
arch/z80/src/ez80/Toolchain.defs: Update some CFLAGS to match CFLAGS from ZDS-II IDE. Apparently, we must say that the CPU is an eZ80F91 event when compiler for eZ80F92.
boards/z80/ez80/z20x: Update linker scripts.
* tools/zds/zds_Config.mk: Move boards/z80/ez80/scripts/eZ80_Config.mk to tools/zds/zds_Config.mk where it can be shared by other ZDS-II platforms.
* boards/z16/z16f: Duplicate changes for new ZDS-II support from ez80
* boards/z80/z8: Duplicate changes for new ZDS-II support from ez80
* arch/z16/src/z16f/Toolchain.defs: Create required Toolchain.defs file for Z16f
arch/z80/arc/ez80/Toolchain.sh: Move more common toolchain definitions from Make.defs.
boards/z80/ez80/scripts/eZ80_Config.mk: Move common defines that override tools/Config.mk to this new file.
This does not solve the ez80 build problem yet but does assure that when the solution is in place, it will automatically apply to all present and future ez80 configurations.
I was over-zealous in arch/z80/src/ez80/ez80f91_handlers.asm. I added space separatros around the '+' operators. Turns out that the ZDS-II assembler can't handle the spaces in that context.
The ez80f92 is similar to the currently supported ez80f91 except that is:
1. Has no PLL and has a maximum CPU frequency of only 20MHz
2. Has no Ethernet controller
3. Timers are different
4. Has no GPIO Port A
5. Timers are different
6. It comes in a smaller package
and other small differences.
This provided the architecture (only) support for the forthcoming z20x port.
And remove syslog_init_e because all initialization is later now and we don't
distinguish the initialition phase anymore after ramlog don't need special
initialize.
Because we can get the same function by CONSOLE_SYSLOG/syslog_console_init.
BTW, it isn't a good choice to use g_ramlogfops as /dev/console since nsh
will read back what it send out which will surprise most people.
it doesn't make sense that iob initialization is in up_initialize
but other memory components initialization is called in nx_start
Change-Id: Id43aeaa995f340c5943f59a0067a483ff3ac34a2
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
To ensure size_t same as toolchain definition in the first place and rename CXX_NEWLONG to ARCH_SIZET_LONG. The change also check whether __SIZE_TYPE__ exist before CONFIG_ARCH_SIZET_LONG so our definition can align with toolchain(gcc/clang) definition automatically.
Call xxx_timer_initialize from clock subsystem to make timer ready for use as soon as possiblei and revert the workaround:
commit 0863e771a9
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Apr 26 07:24:57 2019 -0600
Revert "sched/clock/clock_initialize.c: clock_inittime() needs to be done with CONFIG_SCHED_TICKLESS and clock_initialize should skip clock_inittime() for external RTC case since the RTC isn't ready yet."
This reverts commit 2bc709d4b9.
Commit 2bc709d4b9 was intended to handle the case where up_timer_gettime may not start from zero case. However, this change has the side-effect of breaking every implementation of tickless mode: After this change the tickless timer structures are used before they are initialized in clock_inittime(). Initialization happens later when up_initialize is called() when arm_timer_initialize().
Since the tickless mode timer is very special, one solution might be to
1. Rename xxx_timer_initialize to up_timer_initialize
2 Move up_timer_initialize to include/nuttx/arch.h
3. Call it from clock subsystem instead up_initialize
Basically, this change make timer initialization almost same as rtc initialization(up_rtc_initialize).
For now, however, we just need to revert the change.
Gregory Nutt <gnutt@nuttx.org>
Run all .c and .h files modified in this PR through nxstyle and correct all coding standard problems.
Xiang Xiao <xiaoxiang@xiaomi.com>
Remove TIME_EXTENDED option to more conform C standard
Note: the code/data size increment is small
* Simplify EINTR/ECANCEL error handling
1. Add semaphore uninterruptible wait function
2 .Replace semaphore wait loop with a single uninterruptible wait
3. Replace all sem_xxx to nxsem_xxx
* Unify the void cast usage
1. Remove void cast for function because many place ignore the returned value witout cast
2. Replace void cast for variable with UNUSED macro
Squashed commit of the following:
Author: Gregory Nutt <gnutt@nuttx.org>
Ran nxstyle against many of the affected files. But this job was too big for today. Many of the network drivers under arch are highly non-compiant and generate many, many faults from nxstyle. Those will have to be visited again another day.
Author: Xiang Xiao <xiaoxiang@xiaomi.com>
This effects all network drivers as well as timing related portions of net/: devif_poll_tcp_timer shouldn't be skipped in the multiple card case. devif_timer will be called multiple time in one period if the multiple card exist, the elapsed time calculated for the first callback is right, but the flowing callback in the same period is wrong(very short) because the global variable g_polltimer is used in the calculation. So let's pass the delay time to devif_timer and remove g_polltimer.
Move boards to boards folder
* boards: rename configs folder to boards
This is the proposed layout after the change:
boards: - folder containing board folders
<board>: - name of each board
drivers: - extra drivers specific for platform
include: - header files for the boars
scripts: - extra scripts specific for platform
src: - board specific code
tools: - extra tools specific for platform
<config>: - board specific configuration(s)
Note:
<xxx> names are dependent on platform
This is a logical change to aim to the arch layout but this is a
huge change it should be done in several steps to lower the risk.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Kconfig: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Makefile: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Makefile.*: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Make.defs: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .sh: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .mk: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .c & .h: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .bat: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Squashed commit of the following:
configs/makerlisp/scripts/makerlisp_ram.linkcmd: Fixup .RESET and .STARTUP. These need to be redirected to RAM since they default to ROM.
configs/makerlisp/scripts/makerlisp_ram.linkcmd: Restore some settings that should be unnecessary but are really required by the current implementation.
configs/makerlisp: Rename nsh configuratinon to nsh_flash. Create new configuration, nsh_ram, that is identical to the nsh_flash configuration except that the code runs out of external SRAM.
configs/makerlisp/scripts: Add a linker script to support execution from RAM.
commit f5080f53516a853408dd80f09f85e1d1c139133f
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Mon Jun 17 12:24:22 2019 -0600
arch/z80/src/ez80/ez80_spi.c: SPI driver still does not work. But the driver now has timeouts so that at least it does not hang the system on startup.
commit 5241e9ae643981c43c8c7fa8478a01d0c2e17eb0
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Mon Jun 17 10:45:11 2019 -0600
arch/z80/src/ez80: Fixes to SPI baud rate calculation.
commit ce2e9e3703485563a0a5b6a57e4080ad45d91fd7
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Mon Jun 17 09:29:13 2019 -0600
arch/z80/src/ez80: Cosmetic and unnecessary clean-up or serial driver.
commit 77287c8508a7e3262068d3e8cf1c5f8e27f3a144
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Mon Jun 17 09:08:56 2019 -0600
arch/z80/src/common and arch/z80/src/ez80: Clean up some assertion-related logic.
commit 4d2d3594c22f7240119255825fce2d2437301404
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Mon Jun 17 07:48:21 2019 -0600
configs/makerlisp/nsh/defconfig: Enable STACKDUMP on assertion.
commit 76b7a2faa3f213dd26634dd9440d12f746cac097
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Mon Jun 17 07:47:55 2019 -0600
configs/makerlisp/include/board.h: Don't put the board in reset on a simple assertion, onlhy a full panic.
commit 0a0dc12edcd39c07696769cb7249d8c39a148ccc
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Mon Jun 17 07:46:54 2019 -0600
arch/z80/src/ez80/ez80_rtc_lowerhalf.c: Remove all references to alarm ID.
commit 1a4dba1075fcf6466e87520a8ba66bbf91d696d7
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Mon Jun 17 07:33:29 2019 -0600
configs/makerlisp/src/ez80_bringup.c: Fix an error that was causing MMC/SD to fail to initialize. Unfortunately now the system hangs.
commit 145a395c7a8e73336fe62caf803d108c59e306a5
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Mon Jun 17 07:32:50 2019 -0600
arch/z80/src/ez80: Add an RTC lower half driver. Initial commit is just the STM32 RTC lower half with name changes.
nuttx/arch/z80/src: To properly follow the coding standard, the z80 architecture common should up_mmuinit should be called z80_mmu_initialize.
nuttx/arch/z80/src: To properly follow the coding standard, the z80 architecture common should up_loweserialinit should be called z80_lowserial_initialize.
configs/z80sim/src/z80_serial.c: Remove unused function up_earlyserialinit()
nuttx/arch/z80/src: To properly follow the coding standard, the z80 architecture common should up_serialinit should be called z80_serial_initialize.
nuttx/arch/z80/src: To properly follow the coding standard, the z80 architecture common should up_doirq should be called z80_doirq.
arch/z80/src/common: up_addregion() must be prototyped in nuttx/mm/mm.h, not up_internal.h
arch/z80/src/ez80: Clean-up RTC driver; get a clean compilation. Still untested.
arch/z80/src/ez80: This brings the RTC to code complete, but does not yet compile.
arch/z80/src/ez80/ez80_rtc.c: Bring in badly ported RTC driver from STM32F4. Little more than naming changing at this point not even ready to attempt comilation
arch/z80/src/ez80: Add RTC driver. Initial commit is just the STMF4 RTC driver with name changes.
configs/makerlisp/src/ez80_spi.c: Add hooks needed by SPI driver. Move SPI MMC/SD chip selected configuration from ez80_lowinit.c to here as it done in other NuttX architectures. This enables support for multiple devices on the SPI bus.
Squashed commit of the following:
configs/makerlisp: Update comments about use of serial console.
configs/makerlisp: Add LED support, remove vestiges of button support (the board has no user buttons). Add support for SPI-based MMC/SD card slot.
arch/z80/src/ez80: Fix some link problems.
libs/libc/syslog/lib_syslog.c: The ZDS-II toolchain does not declare va_coy in stdarg.h. I think that the use of va_copy in vsyslog() is no necessary.
configs/makerlisp: Initial configuration directories cloned from ez80f910200zco with little more than naming changes.
