Author: Alan Carvalho de Assis <acassis@gmail.com>
Run nxstyle on all .c and .h and fix all issues
Author: Alin Jerpelea <alin.jerpelea@sony.com>
drivers: mtd: smart: Add smartfs fsck feature
Support fsck to check and repair the smartfs file system. If the power
loss occurs during writing into the flash, the dead space are created
in flash after the next power cycle. To avoid this problem, introduce
fsck and keep the consistency of file system in initializing smartfs.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
commit 60927c5fb6a353994341601f55071c618e97682b
Author: Alin Jerpelea <alin.jerpelea@sony.com>
Date: Thu Dec 28 18:27:21 2017 +0900
drivers: mtd: smart: Fix duplicate sector selection in SmartFS
Add care for 16-bit sequence without CRC.
drivers: mtd: smart: Check CRC of duplicate sectors
In the illegal case by power-loss, when the multiple logical sectors are
duplicated, we compare the sequence number of each sector and select the newer
sector. Just in case, add CRC check for the newer sector. If the newer sector
has CRC error, then we use the older sector.
drivers: mtd: smart: SPI-Flash recovery from the initial error state
The FLASH may be not erased in the initial delivery state.
Just in case for the recovery of this fatal situation,
after once erasing the sector, return the sector as a free sector.
drivers: mtd: smart: Fix error handling in smartfs mtd driver
Add error handling in relocate sector.
drivers: mtd: smart: Fix initialize sector sequence value in smartfs
Fix initialization of sequence value into sector header and also avoid
unaligned memory access when CONFIG_MTD_SMART_ENABLE_CRC=n.
drivers: mtd: smart: Fix handling of duplicate sector in smartfs
In smartfs scan, if duplicate logical sector is found on the device,
then smartfs selects the winner sector by comparing sequence number,
and the loser sector is soon released. Fix a bug this loser sector
is registered into logical-to-physical sector mapping table.
Author: Alan Carvalho de Assis <acassis@gmail.com>
Run nxstyle to check .c and .h files and fix reported issues
Author: liuzhao <happypapa@yeah.net>
Add Quectel EC20 4G LTE Module USB CDC/ACM support
This function fails to compile due to numerous undeclared register definitions used in cxd56_audio_bca_reg.c. This commit replaces the undefined definitions with very similar definitions recommended by GCC (differing only in some spelling).
However, I cannot be certain that this is correct. This must be reviewed, corrected, and verified by Alin Jerpelea. Please do not merge until Alin approves.
The configuration that demonstrates the failure is spresense:audio.
nrf52: add support for GPIO interrupts
nrf52: add macros to decode GPIO PIN and GPIO PORT
nrf52: various cosmetic changes
nrf52: fix GPIO P1 memory address
boards/nrf52840-dk: add support for SPI
boards/nrf52840-dk: add support for LSM6DSL sensor
boards/nrf52840-dk: add support for SX127X radio
In previous commit, mstatus.mie was set when creating a new task
but this change was incorrect and had a side effect such that
a machine interrupt would be enabled just before returning from
interrupt handling routine to switch context.
Also, mstatus.mpp is set to machine mode in up_get_newintctx()
instead of fe310_dispatch_irq().
Author: Alan Carvalho de Assis <acassis@gmail.com>
Check all .c and .h against nxstyle and fix it.
Author: Alin Jerpelea <alin.jerpelea@sony.com>
fs: smartfs: Fix over capacity write
When the remaining capacity of flash is one sector, if a new root
directory is created by file open, then the root directory's chain is
broken and it causes to SmartFS filesystem crash. Once this fatal
problem occurs, it's impossible to recover even if the system reboot.
Fix it by finally update link of root directory.
fs: smartfs: Fix buffer overrun
fs: smartfs: Fix uninitialized variable warnings
fs: smartfs: Memory leak fix
boards: cxd56xx: Update spresense board.h
- Fix PMIC assignment
- Add specific pin configurations for spresense
- Remove unnecessary definitions
arch: cxd56xx: Add ITM syslog init at startup
arch: cxd56xx: Enable DMA settings dynamically
Author: Alan Carvalho de Assis <acassis@gmail.com>
Fix small typos and check against nxstyle
Author: Gregory Nutt <gnutt@nuttx.org>
boards/arm/lpc43xx/bambino-200e/src/lpc43_appinit.c: Eliminate a warning found in build testing.
The removal of (void) from all functions whose return value has been ignored has introduced several new warnings into the build test output. For example in lpc3_appinit(), I now see this:
# define nsh_spifi_initialize() (OK)
and
nsh_spifi_initialize();
which generaterd a new warning: "warning: statement with no effect [-Wunused-value]". This commit fixes that warning.
Description:
Fix two warnings found in build testing: (1) Need to include nuttx/semaphore.h
from prototype of nxsem_post() and (2) need to initialize return value of function.
Uninittialized garbage was being returned on success.Fix two warnings found in
build testing: (1) Need to include nuttx/semaphore.h from prototype of
nxsem_post() and (2) need to initialize return value of function.
Uninittialized garbage was being returned on success.
Author: Alan Carvalho de Assis <acassis@gmail.com>
Verify all .c and .h against nxstyle, fixed the Mixed cases
Author: Alin Jerpelea <alin.jerpelea@sony.com>
cxd56xx improvements (#48)
* arch: cxd56xx: Add size limitation for I2C SCU xfer
This is a fw restriction, unroll loop because it can be transfer
up to 16 bytes.
* arch: cxd56xx: Fix lack of leave_critical_section
add the missing leave_critical_section
* arch: cxd56xx: Remove unnecessary file
this header is duplicate and we can remove it
* arch: cxd56xx: Cosmetic change
remove space after function
* arch: cxd56xx: update topreg registers
the topreg registers are updated to match the cxd5602 HW
* arch: cxd56xx: Add voltage setting for low battery notification
Add voltage setting for low battery notification
* arch: cxd56xx: Improve perfomance of SD card
Improve a problem that the clock of SD Host Controller is lower than the
expected value in SDR25 transfer mode.
* arch: cxd56xx: Cosmetic changes
cleanup to comply with coding standard
* boards: cxd56xx: Cosmetic changes
updates to comply with coding standard
* boards: cxd56xx: Fix SD card cannot mount issue
SD card cannot mount when connecting and disconnecting three times
or more due to wrong state of parameter 'initialized'.
This change enables to skip swtching initialized state when mount
failed.
* arch: cxd56xx: Add size limitation for I2C SCU xfer
This is a fw restriction, unroll loop because it can be transfer
up to 16 bytes.
* arch: cxd56xx: Fix lack of leave_critical_section
add the missing leave_critical_section
* arch: cxd56xx: Remove unnecessary file
this header is duplicate and we can remove it
* arch: cxd56xx: Cosmetic change
remove space after function
* arch: cxd56xx: update topreg registers
the topreg registers are updated to match the cxd5602 HW
* arch: cxd56xx: Add voltage setting for low battery notification
Add voltage setting for low battery notification
* arch: cxd56xx: Improve perfomance of SD card
Improve a problem that the clock of SD Host Controller is lower than the
expected value in SDR25 transfer mode.
* arch: cxd56xx: Cosmetic changes
cleanup to comply with coding standard
* boards: cxd56xx: Cosmetic changes
updates to comply with coding standard
* boards: cxd56xx: Fix SD card cannot mount issue
SD card cannot mount when connecting and disconnecting three times
or more due to wrong state of parameter 'initialized'.
This change enables to skip swtching initialized state when mount
failed.
* tools/nxstyle.c: Donot check unknown file extension files
nxstyle only support c soure file and header file check, donot check
other unknown file extension files.
* tools/checkpatch.sh: Add checkpatch.sh script based on nxstyle tool
Usage:
checkpatch.sh patch-list // default as patch list
checkpatch.sh -p patch-list
checkpatch.sh -c commit-list
checkpatch.sh -f file-list
checkpatch.sh - // read from stdin, which used by git pre-commit hook
And git pre-commit hook could use checkpatch.sh as below:
git diff --cached | ./tools/checkpatch.sh -
Run all .c and .h files in last PR through nxstyle.
Author: 脚蹬破拖鞋 <happypapa@yeah.net>
Add Imxrt usdhc insert or remove detection (#43)
* Add usdhc card insertion and removal detection using interrupt for imxrt.
* Add interrupt handle when usdhc insert or remove.
This commit fixes a compilation error that occurs when enabling the
following configuration items for stm32f7 and stm32h7 architectures:
CONFIG_DEBUG_FEATURES=y
CONFIG_DEBUG_ERROR=y
CONFIG_DEBUG_WARN=y
CONFIG_DEBUG_INFO=y
CONFIG_DEBUG_IRQ=y
CONFIG_DEBUG_IRQ_ERROR=y
CONFIG_DEBUG_IRQ_WARN=y
CONFIG_DEBUG_IRQ_INFO=y
The compiler error for stm32f7:
make[1]: Entering directory '/home/pdupreez/dev/wingunder/nuttx/arch/arm/src'
CC: chip/stm32_irq.c
chip/stm32_irq.c: In function 'up_irqinitialize':
chip/stm32_irq.c:497:29: error: 'STM32_IRQ_NIRQS' undeclared (first use in this function); did you mean 'STM32_IRQ_FIRST'?
stm32_dumpnvic("initial", STM32_IRQ_NIRQS);
^~~~~~~~~~~~~~~
STM32_IRQ_FIRST
chip/stm32_irq.c:497:29: note: each undeclared identifier is reported only once for each function it appears in
make[1]: *** [Makefile:172: stm32_irq.o] Error 1
make[1]: Leaving directory '/home/pdupreez/dev/wingunder/nuttx/arch/arm/src'
And the compiler error for stm32h7:
make[1]: Entering directory '/home/pdupreez/dev/wingunder/nuttx/arch/arm/src'
CC: chip/stm32_irq.c
chip/stm32_irq.c: In function 'stm32_dumpnvic':
chip/stm32_irq.c:164:4: warning: #warning Missing logic [-Wcpp]
# warning Missing logic
^~~~~~~
chip/stm32_irq.c: In function 'up_irqinitialize':
chip/stm32_irq.c:522:29: error: 'STM32_IRQ_NIRQS' undeclared (first use in this function); did you mean 'STM32_IRQ_CRS'?
stm32_dumpnvic("initial", STM32_IRQ_NIRQS);
^~~~~~~~~~~~~~~
STM32_IRQ_CRS
chip/stm32_irq.c:522:29: note: each undeclared identifier is reported only once for each function it appears in
make[1]: *** [Makefile:172: stm32_irq.o] Error 1
make[1]: Leaving directory '/home/pdupreez/dev/wingunder/nuttx/arch/arm/src'
This commit replaces all STM32_IRQ_NIRQS defines with the NR_IRQS
define, which seems to be consistent with the rest of the code in
Nuttx.
* Documentation/NuttXCCodingStandard.html: Remove requirement to decorate ignored returned values with (void).
* sched_mergepending.c: Correct some errors in comments.
Co-authored-by: Gregory Nutt <gnutt@nuttx.org>
Usage: ./nxstyle -r start,count filename
nxstyle with -r option used to parse the range lines rather than the whole file.
Change-Id: I58ec56511fde14d6ec914400a7849e69960a3711
Signed-off-by: liuhaitao <liuhaitao@xiaomi.com>
Author: Alan Carvalho de Assis <acassis@gmail.com>
Fix long line comments in the header files
Author: Mateusz Szafoni <raiden00pl@users.noreply.github.com>
* arch/arm/src/nrf52: add GPIOTE and SAADC registers definitions
* arch/arm/src/nrf52: update some registers definitions
* arch/arm/src/nrf52: add basic I2C support
* arch/arm/src/nrf52: add function to unconfigure GPIO
* arch/arm/src/nrf52/nrf52_lowputc: add missing FAR
Author: patacongo <spudarnia@yahoo.com>
Todo (#34)
* Documentation/NuttXCCodingStandard.html: Remove requirement to decorate ignored returned values with (void).
* TODO: Update TODO list
Co-authored-by: Gregory Nutt <gnutt@nuttx.org>
Author: Alan Carvalho de Assis <acassis@gmail.com>
Run all .h and .c files modified in last PR through nxstyle.
Author: Xiang Xiao <xiaoxiang@xiaomi.com>
Fix stm32l4_otgfshost.c: error: 'ret' undeclared (#32)
result by commit 6a3c2aded6
Change-Id: I68ba79417d8da102da8d91c74496961aef242dd9
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Run all .c and .h files in last PR through tools/nxstyle and fix all complaints.
Author: macman88 <jjlange91@gmail.com>
LPC17xx serial updates (#29)
* Save CONFIG_ARCH_BOARD_CUSTOM when running 'make savedefconfig'
* Don't compile up_earlyserialinit if USE_EARLYSERIALINIT is not defined
* Added support for RS485 direction control on LPC17xx UART1
* First pass at fractional baud rate divider on LPC17xx/40xx
* Added support for fractional divider to console UART
