arch/arm/src/tiva/common/tiva_timerlib.c:
* tiva_gptm_configure() and tiva_gptm_release(): Fix error: Was calling
tiva_emac_periphrdy() instead of tiva_gptm_periphrdy().
arch/arm/src/tiva/tiva_timer.h:
* Fix error in "abcde" description of bit flag defines.
kinetis:i2c transfer ensure correct result returned
kinetis_i2c_transfer released the mutex then fetched
the state, this resulted in returning the correct
results.
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Move boards to boards folder
* boards: rename configs folder to boards
This is the proposed layout after the change:
boards: - folder containing board folders
<board>: - name of each board
drivers: - extra drivers specific for platform
include: - header files for the boars
scripts: - extra scripts specific for platform
src: - board specific code
tools: - extra tools specific for platform
<config>: - board specific configuration(s)
Note:
<xxx> names are dependent on platform
This is a logical change to aim to the arch layout but this is a
huge change it should be done in several steps to lower the risk.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Kconfig: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Makefile: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Makefile.*: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Make.defs: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .sh: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .mk: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .c & .h: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .bat: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Rationale: TM4C1294NC is ambiguous:
TM4C1294NCPDT is a 128-TQFP
TM4C1294NCZAD is a 212-NFBGA
The TM4C1294NC part currently supported by NuttX is the TM4C1294NCPDT used on the TI EK-TM4C1294XL "Connected LaunchPad" (see configs/tm4c1294-launchpad). To ensure the correct part is fully specified, this commit updates all TM4C1294NC identifiers to TM4C1294NCPDT.
Rename:
CONFIG_ARCH_CHIP_TM4C1294NC to CONFIG_ARCH_CHIP_TM4C1294NCPDT
ARCH_CHIP_TM4C1294NC to ARCH_CHIP_TM4C1294NCPDT
TM4C1294NC to TM4C1294NCPDT
Rationale: In terms of firmware programming, there is no functional difference between these parts:
TM4C123GH6PMI7
TM4C123GH6PMI7R
TM4C123GH6PMT7
TM4C123GH6PMT7R
From a programming standpoint, all of the above parts are TM4C123GH6PM, which means it doesn't make sense to differentiate between PM and PMI. (The PM means 64-LQFP. The I means temperature range -40C to +85C. It could be T meaning -40C to +105C. The R means it ships in Tape and Reel packaging as opposed to Tray.)
arch/arm/include/tiva/chip.h:
arch/arm/include/tiva/tm4c_irq.h:
arch/arm/src/tiva/hardware/lm/lm3s_flash.h:
arch/arm/src/tiva/hardware/tm4c/tm4c_pinmap.h:
configs/tm4c123g-launchpad/README.txt:
configs/tm4c123g-launchpad/nsh/defconfig:
Rename: CONFIG_ARCH_CHIP_TM4C123GH6PMI to CONFIG_ARCH_CHIP_TM4C123GH6PM
arch/arm/src/tiva/Kconfig:
configs/Kconfig:
Rename: ARCH_CHIP_TM4C123GH6PMI to ARCH_CHIP_TM4C123GH6PM
arch/arm/src/tiva/hardware/tm4c/tm4c_memorymap.h:
Rename: CONFIG_ARCH_CHIP_TM4C123GH6PMI to CONFIG_ARCH_CHIP_TM4C123GH6PM
Remove redundant Peripheral Base Addresses section. There were two identical copies, one for CONFIG_ARCH_CHIP_TM4C123GH6PMI and another for CONFIG_ARCH_CHIP_TM4C123GH6PM.
Testing of the WiFi is minimal so far but functionality is proven. I'm specifically not happy that the driver doesn't recover elegantly from a DMA data checksum failure, but that is an issue that can be dealt with in due course ... I'm trying to get the rest of the interfaces fleshed out and the hardware proven so it can go for pre-production build. I _think_ there's only Bluetooth and USB-device left to implement now.
- Fix for mx25rxx driver as it does not work properly
- Add mx25rxx memory chip & smartfs support in b-l475e-iot01a/nsh config
- Update smartfs smart_scan() function
stm32f7: Fixes bad preprocessor logic preventing USB OTG HS to work when used without external ULPI.
Approved-by: David Sidrane <david.sidrane@nscdg.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Add support for LPC40xx family chips
* Corrected a few peripheral definitions and pin functions for the LPC17xx family.
Added configuration options, chip definitions, and additional pin functions for the LPC40xx family.
Added board configurations for Embedded Artists LPC4088 Quickstart board and LPC4088 Developer's kit. These configurations are still something of a work in progress. In particular, the LCD functionality is untested.
* First pass rename in *.c and *.h files.
* Renamed LPC17XX to LPC17XX_40XX in config files
* Rplaced LPC17xx with LPC17xx/LPC40xx in .c files
* Replaced LPC17xx with LPC17xx/LPC40xx in .h files
* Updated some documentation
* Working on moving directories
* moved arch/arm/src/lpc17xx and arch/arm/include/lpc17xx to lpc17xx_40xx
* Renamed LPC17_* constants / configuration options to LPC17_40_*
* Updated chip family name defines
* Renamed some chip-specific files
* Updated references to renamed files
* Updated references to lpc17_ to lpc17_40_
* Renamed source files from lpc17_* to lpc17_40_*
* Clean up white space
Approved-by: Gregory Nutt <gnutt@nuttx.org>
drivers/lcd/tda19988.c: Now uses the new common videomode structure of include/nuttx/video/videomode.h as do other video components.
video/, include/nuttx/video/videomode.h: Separate EDID and from videomode managment. They really are separate things.
back at physical address 0x2007C000 and 0x20080000 (i.e. right below and right
above a 512 KiB boundary). Memory from those two blocks is considered
continuous when assigned to a heap.
In the protected build mode, when the memory protection unit is used, though,
it must be split into two MPU regions. This is because MPU regions must be
naturally aligned, and the 32KiB continuous address space of the two 16KiB AHB
SRAM blocks does not start at an address divisible by 32KiB.
The only other configurations that use protected build mode on lpc17xx are
currently open1788/knsh and open1788/knxterm. The LPC1788 has the AHB SRAM
blocks mapped more sanely (from an MPU region point of view), which is
probably why no problems emerged here. Both still compile with my change and
other than wasting an MPU region (which would otherwise remain unused) should
work fine. That said, I have no hardware to confirm.
arch/arm/src/am335x: Add logic to map the framebuffer to a non-cached, non-buffered memory region.
arch/arm/src/am335x: Remove struct am335x_fbinfo_s. Replaced with configuration settings that provide the same information.
Squashed commit of the following:
arch/arm/src/am335x/am335x_lcdc.c: LCD driver now compiles.
arch/arm/src/am335x/am335x_lcd.c: This brings the LCD driver to code complete. Have not yet attempted to compile.
arch/arm/src/am335x/am335x_edid.c: Framebuffer is pre-allocated. In verification of video mode, include a test to assure that the video mode can be supported by the pre-allocated framebuffer memory.
arch/arm/src/am335x/am335x_lcd.c: At a little bit of LCD initialization logic. There is a long way to go.
arch/arm/src/am335x/am335x_edid.c: Add am335x_lcd_videomode() which provides an alternative way of initializing the LCD controller.
arch/arm/src/am335x/am335x_edid.c: edit.h has move to include/nuttx/video.
arch/arm/src/am335x/hardware/am335x_cm.h: Fix a typo in a macro name.
arch/arm/src/am335x/am335x_edid.c: Integrate video/edid support.
arch/arm/src/am335x/am335x_edid.c: Fall back to VGA mode is not valid videomode is availabe in the EDID data.
arch/arm/src/am335x/am335x_edid.c: Fixes for a partially clean compile.
arch/arm/src/am335x/am335x_edid.c: Add basic logic to convert EDID montor descriptions into a form usable for LCD configuration.
arch/arm/src/am335x: Add framework (only) for an LCD driver. Initial commit is simply the LPC54 framebuffer driver with naming changes.
Improve gs2200m performance
* arch/arm/src/cxd56xx: Fix dma initialization in cxd56_dmac.c
up_dma_initialize() must be used instead of up_dmainitialize()
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* drivers/wireless: Introduce CONFIG_WL_GS2200M_SPI_FREQUENCY
Also, changed usleep(100) to up_udelay(100) to avoid invalid response.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* configs/spresense/wifi: Improve performance for webserver
This commit changes followings.
1. Enable SPI DMA for both TX and RX
2. Increase SPI clock speed from 4MHz to 10MHz
3. Increase buffer size for sendfile() from 512B to 1KB
4. Enable sendfile() for webserver
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arch/arm/src/tiva: Add a workaround for tiva with qemu
With qemu, tiva_ifup() hangs because ethernet link status can not
be set correctly. This PR is a workaround to avoid this issue.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
configs: spresense: add I2CTOOL support and extend GPIO for future use
* arch: arm: cxd56xx: add delay support
add delay support for cxd56xx chip
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: register I2C busses
for development is usefull to register I2C busses when the I2CTOOL
is built
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs:spresense: enable GPIO interface
enable GPIO interface on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arch: arm: cxd56xx: SCU, ADC, I2C
* nuttx: configs: spresense: LEDS: fix warnings
In the initial code several errors were missed because I pushed
the dirty code.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add Sensor Control Unit (SCU)
Add Sensor Control Unit (SCU) on cxd56xx chip
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add I2C support
add I2C support on cxd56xx chip
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add ADC interface support
Add ADC interface support on cxd56xx chip
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: Use DMAC for reading sensing data
Use DMAC for reading sensing data from SCU on cxd56xx chip
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: code style sanitization
NuttX does not use Deoxygen for documentation and no file should contain Doxygen tags or Doxygen style comments.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: enable I2CDEV
add enable I2CDEV for spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: add notification LEDs
Add usefull diagnostic LEDs on the speresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arch: arm: cxd56xx: add UID support
* arch: arm: cxd56xx: add UID support
Add support to be able to read the HW UID
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: enable USERLEDS
add USERLED for spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arch: arm: cxd56xx: PM and PWM
* configs: spresense: add SPI configuration
add SPI configuration for spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add support for PWM
add support for PWM for cxd56xx
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: enable PWM support
enable PWM support on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add Power Management PROCFS support
the powermanager procfs support will export
/proc/pm:
clock
power
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: enable powermanager procfs support
The powermanager procfs is disabled by default and need to be enabled
by the CONFIG_CXD56_PM_PROCFS option
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add timer driver
Add timer driver for cxd56xx.
NOTE
The timer allows a divider of 1, 16 and 256 options
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add Watch Dog Timer
Add Watch Dog Timer on cxd56xx
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: enable timer
the platform support has been added and now we can use the timers
on spresense board.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: enable WatchDog timer
The platform support has been added and now we can use the WatchDog
Timer on spresense board.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
stm32 h7 Add ADC and a few fixes for timer and Serial
* stm32h7:Fix error when SINGLEWIRE or CONFIG_STM32H7_SERIALBRK_BSDCOMPAT defined
* stm32h7:time fixed compile errors with TIM13,TIM14, TIM7
* stm32h7:Added ADC Driver
* stmh7x3:Added ADC pins to pin map
* stm32h7:Added ADC clocking
* nucleo-h743zi:Add ADC
Approved-by: Gregory Nutt <gnutt@nuttx.org>
rndis on spresense
* arch/arm/src/cxd56xx: Fix ep0 out packet handling in cxd56_usbdev.c
This change fixes to handle ep0 out packet which exceeds EP0_MAXSIZE.
For example, 76 bytes of out packet is sent from rndis host during
rndis negotiation and finally the packet is split into two out packets
(64 bytes out packet + 12 bytes out packet). To handle these packets,
actual ep0reqlen is stored during ep0 out setup stage, and if all
out packets are received, it dispatches to cxd56_ep0setup(), otherwise,
it sets up the internal USB DMA to receive remaining out packets.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* configs/spresense: Add support for rndis configuration
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Add syscontrol for cxd56xx
* arch: arm: cxd56xx: add sysctl
Add the syscontrol implementation for cxd56xx.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: timer updates
Add the function to change the clock speed.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: cxd56_uart updates
Add pinctrl and clock ctrl functionality.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add conditional for SDHCI
The cxd56_sdhci should be built only if CONFIG_CXD56_SDIO is selected
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arch: arm: cxd56xx: add Power Management support
* arch: arm: cxd56xx: add Power Management support
Add power management on the cxd56xx
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add Far API
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arch: arm: cxd56xx: add support for USB and SDIO
* arch: arm: cxd56xx: add support for USB connectivity
Add basic support for USB connectivity
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add SDHCI support
We add SDHCI driver for the cxd56xx
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arch: arm: cxd56xx: add Package Configuration
The CXD56xx can come in FCBGA 185 pin or WLCSP 100 pin package.
For each package we have to pick the right pin setup.
The default configuration is set to FCBGA 185 pin package
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Improvements for STM32 PWM
arch/arm/src/stm32/stm32_pwm: add support for all PWM modes
arch/arm/src/stm32/stm32_pwm: add interface to change PWM mode
arch/arm/src/stm32/stm32_pwm: refactor pwm_mode_configure()
arch/arm/src/stm32/stm32_pwm: STM32_PWM_CHANx corresponds to the timer channel and STM32_PWM_OUTx corresponds to the timer channel output
arch/arm/src/stm32/stm32_pwm: add CHAN5 and CHAN6 to PWM_TIMx_NCHANNELS
arch/arm/src/stm32/stm32_pwm: calculate the PWM_TIMx_NCHANNELS if CONFIG_STM32_PWM_MULTICHAN is selected
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Squashed commit of the following:
arch/arm: Rename include/stm32f0l0 and src/stm32f0l0 to stm32f0l0g0.
Change all occurrences of lower-case stm32f0l0 to stm32f0l0g0.
Change all occurrences of upper-case STM32F0L0 to STM32F0L0G0.
arch/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
sched/ audio/ crypto/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
Documentation/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
fs/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
graphics/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
net/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
drivers/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
include/, syscall/, wireless/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
configs/: Remove all references to CONFIG_DISABLE_POLL. Standard POSIX poll can no longer be disabled.
Port AES and RND to STM32 M0 + some improvements
arch/arm/src/stm32f0l0/stm32_rng.c: change the function names to use the stm32_rng prefix
arch/arm/src/stm32f0l0/stm32_usbdev.c: move HSI48 enable to stm32xx_rcc.c
arch/arm/src/stm32f0l0: add support for AES
arch/arm/src/stm32f0l0: add support for RND
arch/arm/src/stm32f0l0: add HSI48 support for L0
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Port STM32F7 I2C to STM32F3 and STM32F0L0
arch/arm/src/stm32: port I2C IPv2 driver from F7 (only F3 chips)
arch/arm/src/stm32f0l0: port I2C IPv2 driver from F7
configs/b-l072z-lrwan1: nxlines_oled example (ssd1306)
configs/b-l072z-lrwan1: support for the I2C tool
configs/nucleo-f303ze: nxlines_oled example (ssd1306)
arch/arm/src/stm32h7/chip.h: cosmetics
arch/arm/src/stm32/chip/stm32_tim.h: cosmetics
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Initial ADC support and some improvemnets for the STM32 M0
arch/arm/src/stm32f0l0/Kconfig: improvements
configs/b-l072z-lrwan1: add ADC example
Approved-by: Gregory Nutt <gnutt@nuttx.org>
libs/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
syscall/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
wireless/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
Documentation/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
include/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
drivers/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
sched/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
configs: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/xtensa: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/z80: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/x86: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/renesas and arch/risc-v: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/or1k: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/misoc: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/mips: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/avr: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/arm: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/arm/src/stm32/stm32_i2s.c: In debug assertions, it on a sample rate of 0, but based on other code comments this value implies disabling the i2s master clock.
arch/arm/src/stm32/stm32_usbhost.h and arch/arm/src/stm32/Kconfig: Allow vbus monitoring for the OTG_HS host driver.
stm32f7:i2c track bad state
The previous commit was true draconian.
Now we track bad state and so the SW
reset only when it occurs.
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Support for STM32L071X and a few improvements for STM32F0L0
arch/arm/src/stm32f0l0: add peripherals configuration for STM32L0
arch/arm/src/stm32f0l0: a few fixes for USART
arch/arm/include/stm32f0l0/stm32f0_irq.h: use names as in other STM32
arch/arm/include/stm32f0l0/chip.h: use names as in other STM32
Approved-by: Gregory Nutt <gnutt@nuttx.org>
include/nuttx/nx/nxcursor.h: Add a header file descrbing the implementation of an NX cursor interface. There is no implementation in place yet.
include/nuttx/video/cursor.h: Separate out cursor definitions from fb.h. Other graphic interfaces other than a framebuffer may support a cursor, possible a software cursor.
Added support for Ethernet PHY ioctl() on LPC17xx.
* Added support for Ethernet PHY ioctl() on LPC17xx.
* Fixed whitespace.
* One more time.
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Added support for KSZ8081RNA PHY to LPC17xx Ethernet driver.
* Added support for KSZ8081RNA PHY to LPC17xx Ethernet driver.
* Updated PHY error message
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arch/stm32f7: Support bypassing the input clock divider on the SDMMC interface. This enables using the full clock speed provided to the SDMMC interface with no dividing.
Approved-by: Gregory Nutt <gnutt@nuttx.org>
This change removes the board_reset() implementation from the architecture-specific code and re-implements in the src/ directory of each board that has CONFIG_BOARDCTL_RESET enabled. That is the correct functional partitioning.
arch/arm/src/stm32h7: initial support for protected build mode. Not functional yet. It compiles without errors and passes initialization but after entering the user app strange things happen.
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Add three patches about STM32 intherupts and network loopback files
* Add the missing macro STM32_IRQ_NIRQS used by ./arch/arm/src/stm32f7/stm32_irq.c
Signed-off-by: Kejun ZHOU <zhoukejun@outlook.com>
* The struct in_addr doesn't have the member sin_addr.
Signed-off-by: Kejun ZHOU <zhoukejun@outlook.com>
* The function lib_lo_ipv6match() is for IPv6.
Correct the function it calls from lib_lo_ipv4matchto() to lib_lo_ipv6match().
Also add CONFIG_NET_IPv6 for configuration.
Signed-off-by: Kejun ZHOU <zhoukejun@outlook.com>
Initial OTG support for STM32H7 and some minor improvements
arch/arm/src/stm32h7/stm32h7x3xx_rcc.c: add support for HSI48 clock
configs/nucleo-f207zg: add support for USB and initialize CDCACM if configured
configs/nucleo-h743zi: add support for USB and initialize CDCACM if configured
drivers/usbdev/Kconfig: fix type for USBDEV_TRACE_INITIALIDSET
configs/teensy-3.x/usbnsh/defconfig: update config according to change in USBDEV_TRACE_INITIALIDSET
Approved-by: Gregory Nutt <gnutt@nuttx.org>
libs/libc/pthread/pthread_spinlock.c: Resolve several TODO issues by accessing up_testset() via the boardctl() interface rather than attempting to call it directly.
configs/boardctl.c, include/sys/boardctl.h: Add access to architecture-specific up_testset() via boardctl().
arch/Kconfig's, sched/Kconfig, and include/nuttx/spinlock.h: Spinlocks are not available unless the architecture supports the up_testset() operation.
Author: Gregory Nutt <gnutt@nuttx.org>
arch/arm/src/imxrt/: Fix complaints from tools/nxstyle in new LCD files.
Use tools/lowhex to convert hexadecimal constants to lower case.
Use tools/rmcr to review white space at the end of lines.
Author: Johannes <nivus.entwicklung@gmail.com>
arch/arm/src/imxrt and configs/imxrt1050-evk: Adds framebuffer support for thje i.MXRT 1050. Includdd DCD initialization for SDRAM to provide space for the framebufer. External code I used/ported is from NXP and is BSD 3-clause license.
Initial DMA support for STM32H7
arch/arm/src/stm32h7: SPI DMA mode
arch/arm/src/stm32h7/chip/stm32h7x3xx_memorymap.h: add base addresses for D1, D2 and D3 domain; use 2 bytes to specify memory region
arch/arm/src/stm32h7/stm32h7x3xx_rcc.c: add D1 domain core prescaler configuration
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Improvements for H7 towards the DMA support
arch/arm/include/stm32h7/stm32h7x3xx_irq.h: fix typos and rename DMA1/2 irq names to match those from other STM32
arch/arm/src/stm32h7/chip/stm32_bdma.h: add auxiliary definitions
arch/arm/src/stm32h7/chip/stm32_dma.h: cosmetic changes
arch/arm/src/stm32h7/chip/stm32_dmamux.h: add auxliary definitions and fix some typos
arch/arm/src/stm32h7/chip/stm32_mdma.h: add auxliary definitions and fix some typos
arch/arm/src/stm32h7/chip/stm32h7x3xx_dmamux.h: add DMAMAP definitions for MDMA, DMA1, DMA2 and BDMA
arch/arm/src/stm32h7/chip/stm32h7x3xx_memorymap.h: fix AHB1 base adresses and add some address blocks
arch/arm/src/stm32h7/chip/stm32h7x3xx_rcc.h: fix some definitions to match other STM32 ports
arch/arm/src/stm32h7/stm32_allocateheap.c: use SRAM from D2 domain (SRAM123) for now
arch/arm/src/stm32h7/stm32h7x3xx_rcc.c: enable clock for MDMA and BDMA
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Fixed coding standard error in several files. Use of while( is incorrect; a space is required between while and (. Also ran tools/nxstyle and fix thoses complaints as well in most files.
Changes to comply with coding standard. Mostly focused on files with missing space after keyword in if(, switch(, and for(. Offending files also got changes to comply with tools nxstyle. If there were logs of nxstyle complaints, the file also got a taste of tools/indent.sh. Still need to fix occurrences of while( with missing space. There are a lot of them.
Master
arch/arm/src/stm32f0l0: SPI support for F0
arch/arm/src/stm32f0l0/Kconfig: L0 parts should select STM32F0L0_STM32L0
arch/arm/src/stm32f0l0/hardware: unify names for ADC/DAC/DMA/CAN
drivers/wireless/lpwan/sx127x/sx127x.c: return immediately when ISR0 is called but sx127x is not initialized
configs/nucleo-f091rc: support for sx127x
configs/nucleo-l073rz: cosmetics
configs/b-l072z-lrwan1/include/board.h: use HSI as default clock source and fix typo in SPI1 pins
Approved-by: GregoryN <gnutt@nuttx.org>
configs/launchxl-cc1312r1: Correct DIOs used to provide the UART0 serial console.
Status: Board boots to NSH prompt now. But I am not getting serial input. Things are probably not very stable in general.
arch/arm/src/tiva/cc13xx/cc13xx_prcm.c: Fix reverse bit modification: Set the bit to enabled clocking, clear the bit to dissable clocking.
arch/arm/src/tiva/cc13xx/cc13xx_enablepwr.c: Use correct index for determining if this the SERIAL or PERIPH power domain.
Squashed commit of the following:
configs/: The few configurations that formerly set CONFIG_NFILE_DESCRIPTORS=0 should not default, rather they should set the number of descriptors to 3.
fs/: Remove all conditional logic based on CONFIG_NFILE_DESCRIPTORS == 0
tools/: Tools updates for changes to usage of CONFIG_NFILE_DESCRIPTORS.
syscall/: Remove all conditional logic based on CONFIG_NFILE_DESCRIPTORS == 0
libs/: Remove all conditional logic based on CONFIG_NFILE_DESCRIPTORS == 0
include/: Remove all conditional logic based on CONFIG_NFILE_DESCRIPTORS == 0
drivers/: Remove all conditional logic based on CONFIG_NFILE_DESCRIPTORS == 0
Documentation/: Remove all references to CONFIG_NFILE_DESCRIPTORS == 0
binfmt/: Remove all conditional logic based on CONFIG_NFILE_DESCRIPTORS == 0
arch/: Remove all conditional logic based on CONFIG_NFILE_DESCRIPTORS == 0
net/: Remove all conditional logic based on CONFIG_NFILE_DESCRIPTORS == 0
sched/: Remove all conditional logic based on CONFIG_NFILE_DESCRIPTORS == 0
sched/Kconfig: CONFIG_NFILE_DESCRIPTORS may no longer to set to a value less than 3
configs/: Remove all settings for CONFIG_NFILE_DESCRIPTORS < 3
sched/init/nx_bringup.c: Fix a naming collision.
sched/init: Rename os_start() to nx_start()
sched/init: Rename os_smp* to nx_smp*
sched/init: Rename os_bringup to nx_bringup
sched/init: rename all internal static functions to begin with nx_ vs os_
Squashed commit of the following:
Trivial, cosmetic
sched/, arch/, and include: Rename task_vforkstart() as nxtask_vforkstart()
sched/, arch/, and include: Rename task_vforkabort() as nxtask_vforkabort()
sched/, arch/, and include: Rename task_vforksetup() as nxtask_vfork_setup()
sched/: Rename notify_cancellation() as nxnotify_cancellation()
sched/: Rename task_recover() to nxtask_recover()
sched/task, sched/pthread/, Documentation/: Rename task_argsetup() and task_terminate() to nxtask_argsetup() and nxtask_terminate(), respectively.
sched/task: Rename task_schedsetup() to nxtask_schedsetup()
sched/ (plus some binfmt/, include/, and arch/): Rename task_start() and task_starthook() to nxtask_start() and nxtask_starthook().
arch/ and sched/: Rename task_exit() and task_exithook() to nxtask_exit() and nxtask_exithook(), respectively.
sched/task: Rename all internal, static, functions to begin with the nx prefix.
arch/arm/src/samv7/sam_emac.c: Fixes rxdesc index logic to handle Buffer Not Available (BNA) condition.
If a SOF is found, but no EOF, don't move past the frame. Instead, keep the index at the SOF buffer until the rest of the data is written.
This fixes a receiver lockup condition where the peripheral and this driver get out of sync with there head pointers. In this case the driver has moved past buffers it owns, without clearing ownership, which results in the peripheral and driver in a deadlock with each other.
Approved-by: GregoryN <gnutt@nuttx.org>
2./arch/arm/src/samv7/sam_qspi.c compiling error when set CONFIG_SAMV7_QSPI_DLYBCT
3. fix compiling error when set CONFIG_BOARDCTL_IOCTL/CONFIG_BOARDCTL_UNIQUEID
Improvements in STM32 ADC, PWM and TIM
arch/arm/src/stm32/chip/stm32_adc_v2.h: missing T1TRGO2 for JEXTSEL
arch/arm/src/stm32/stm32_adc: configure injected channels external trigger when ADC enabled
arch/arm/src/stm32/stm32_adc: update injected conversion queue of context after configuration
arch/arm/src/stm32/stm32_adc: fix sample time configuration for channels. The array index for channels was missing
arch/arm/src/stm32/stm32_adc: support for offset configuration
arch/arm/src/stm32/stm32_pwm: fix TRGO/TRGO2 configuration
arch/arm/src/stm32/stm32_pwm: support for advanced timers channel 5 and 6
Approved-by: GregoryN <gnutt@nuttx.org>
Improvements for STM32 PWM
arch/arm/src/stm32/stm32_pwm: fix polarity and IDLE state configuration for advanced timer PWM
include/dsp.h: raise error if math.h not present
Approved-by: GregoryN <gnutt@nuttx.org>
arch/arm/src/tiva/hardware: Add CC13xx SMPH and AUX SMPH header files. Still need DDI0 OSC header file for CC13x0 compilation.
arch/arm/src/tiva/cc13xx: A few changes toward getting the launchxl-cc1310/nsh configuration to build
Squashed commit of the following:
confgs/launchxl-cc1310: Add board support for the LaunchXL-CC1310. This is a work in progress and does not yet build error free.
arch/arm/src/tiva/cc13xx: cc13x0_trim.c now compiles; Make xxx_rom.h header files conform a little more closely to the NuttX coding style.
arch/arm/src/tiva/cc13xx: CC13x2 (V1 and V2) rom.c files now build with no errors or warnings. Still have to work through the CC13x0 version.
arch/arm/src/tiva/hardware: Add CC13x0/CC13x2_CC26x2 AON BATMON register definition header file.
arch/arm/src/tiva/cc13xx: A little more progress converting TI DriverLib ROM code to NuttX coding style. Lots of possibilities for breakage here!
arch/arm/src/tiva/cc13xx: Remove functions from cc13x._rom.c that are defined from ROM access in cc13x._rom.h; Add prototypes in cc13x._rom.h for functions in cc13x._rom.c that are not defined in cc13x._rom.h.
arch/arm/src/tiva/cc13xx: Remove some dangling whitespace at the end of lines.
arch/arm/src/tiva/cc13xx: Second (and final) round of name changes to get ROM function-like defines consistent with NuttX coding standard
arch/arm/src/tiva/cc13xx: Fix a few errors in last big name conversion.
arch/arm/src/tiva/cc13xx: First round of name changes to get ROM function-like defines consistent with NuttX coding standard
arch/arm/src/tiva/cc13xx: Remove ROM_ prefix from function-like defines.
arch/arm/src/tiva/hardware: Completes the CC13x2 AUX SYSIF header file.
arch/arm/src/tiva/hardware: Progress on the CC13x2 AUX SYSIF header file. Almost complete.
arch/arm/src/tiva/hardware: Port needs aux_sysif.h header file.
arch/arm/src/tiva/cc13xx/cc13x0_rom.h: Fix a typo
arch/arm/src/tiva/cc13xx: More changes to TI DriverLib ROM header files for NuttX coding standard.
arch/arm/src/tiva/cc13xx: Convert some (but not all) TI DriverLib ROM function names to NuttX coding standard. More to be done.
arm/src/tiva/cc13xx: ROM header files: missed a couple of conversions of sructure field names to lower case (vs CamelCase).
arm/src/tiva/cc13xx: ROM header files: type'ed names must be lower case per coding standard (not upper case); structure field names must be lower case per coding standard (not CamelCase).
arch/arm/src/tiva/cc13xx: Trim logic needs to include matching ROM DriverLib interface header file.
arch/arm/src/tiva/cc13xx: Add ROM DriverLib header files. Do not yet fully conform to the NuttX coding style.
arch/arm/src/tiva/cc13xx: Trim code now kind of looks like NuttX code. But does not yet compile.
arch/arm/src/tiva/cc13xx: The first few, feeble steps toward getting the overall trim files compatible with the requirements of the NuttX coding standard.
arch/arm/src/tiva/cc13xx: Replace last of TI hardware access macros with NuttX hardware access macros.
arch/arm/src/tiva/cc13xx: Change TI HWREGB to NuttX getreg8 or putreg8 in trim logic.
arch/arm/src/tiva/cc13xx: Change TI HWREGBITW to NuttX getreg32/putreg32 sequence in trim logic.
arch/arm/src/tiva/hardware/cc13x2_cc26x2/cc13x2_cc26x2_ddi0_osc.h: Completes the DDIO OSC header file.
cc13x2_cc26x2/cc13x2_cc26x2_ddi0_osc.h: Updated, but still not finished.
arch/arm/src/tiva/hardware/cc13x2_cc26x2/cc13x2_cc26x2_ddi0_osc.h: Add DDI0 OSC header file. Still a work in progress. Does not yet conform to the NuttX coding standard.
Change _M and _S to _MASK and _SHIFT.
Some minor improvements.
Clean up typos in some comments.
Run all new files against tools/indent.sh
arch/arm/src/tiva/cc13xx: Bring in trim files from SDK. Convert to C-style comments, lowercase hex contants. Remove Windows-style line endings.
I still observe data abort crash if I compile the code with optimization enabled.
The next steps are to investigate the optimization issue and add Watchdog module. Currently, NSH does not run for a long time ;)
arch/arm/src/am335x/am335x_irq.c: Correct interrupt processing routine
configs/beaglebone-black/nsh/defconfig: Enable debug compilation options. Otherwise data abort crash is observed
arch/arm/src/am335x/am335x_lowputc.c and arch/arm/src/am335x/chip/am335x_uart.h: UART-related cosmetic changes
arch/arm/src/am335x/am335x_timerisr.c: Make sure that Timer 1 interrupts are disabled before any access to peripheral registers
stm32f0l0: SPI and GPIO EXTI support
arch/arm/src/stm32f0l0: add support for GPIO EXTI
configs/nucleo-l073rz: support for nrf24l01
configs/b-l072z-lrwan1/include/board.h: add note about onboard Murata CMWX1ZZABZ-09 module and definitions for available peripherals
Approved-by: GregoryN <gnutt@nuttx.org>
Masayuki Ishikawa reports that this commit breaks ALL PROTECTED mode builds.
It violates the basic requirements of the use of the MPU in protected mode. Those basic requirements are:
1. The MPU region must be aligned to the base address of the memory region being mapped (it may NEVER extend before the memory region). That is, the following MUST always be zero:
(base & ((1 << l2size) - 1))
2. The MPU region must never extend beyond the end of the memory region. That is, the following must be true:
size >= (1 << l2size)
This reverts commit 8b63d02309.
Squashed commit of the following:
Author: Gregory Nutt <gnutt@nuttx.org>
Many small changes related to coding style.
Author: Petro Karashchenko <petro.karashchenko@gmail.com>
configs/beaglebone-black: Adds initial support for the BeagleBone Black board.
arch/arm/src/am335x: Adds initial support for the TI AM355x family.
Fix lc823450 start
* arch/arm/src/lc823450: Use CONFIG_STACK_COLORATION instead of CONFIG_DEBUG_STACK
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* arch/arm/src/lc823450: Fix go_os_start() in lc823450_start.c
I found a bug in go_os_start() that it returns immediately
because it does not compare r1 to zero. This commit fixes
this bug. Also, this commit fixes its description.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: GregoryN <gnutt@nuttx.org>
Squashed commit of the following:
arch/arm/src/stm32f0l0: Various changes for a clean compilation. Still does not compile correctly due to missing FLASH latency definitions.
arch/arm/src/stm32f0l0/hardware: Add framework for the STM32 L0. Currently set to same as the STM32F0.
arch/arm/src/stm32f0l0/hardware: Very fragmentary FLASH header register definitions for the STM32 L0.
arch/arm/src/stm32f0l0: Bring in DMA v1. Cannot possibly be functionaly yet due to the limited number for M0 interrupts.
arch/arm/src/stm32f0l0: Add STM32 F0/L0 LSE and backup power domain controls.
arch/arm/src/stm32f0l0/hardware/stm32l0_pwr.h: Add STM32L0 PWR header file.
arch/arm/include/stm32f0l0/chip.h: Clean up WIP chip header file.
arch/arm/include/stm32f0l0/chip.h: WIP.
arm/src/stm32f0l0: Resolve some small differences between F0 and L0 GPIO pin options.
arch/arm/src/stm32f0l0: Better integrate STM32L0 header files.
nuttx/arch/arm/include/stm32f0l0: Add STM32L0 IRQ number definition file.
arch/arm/src/stm32f0l0: Add STM32L0 RCC driver.
arch/arm/src/stm32f0l0/hardware: Adds basic STM32L0 header files.
arch/arm/src/stm32f0l0: Add STM32L0 chip selections.
configs/: Hook new STM32L0 boards into the configuration system.
configs: nucleo boards use as default ST LINK MCO as clock input from MCU and for this HSEBYP must be enabled
configs: add basic support for nucleo-l073rz
configs: add basic support for b-l072z-lrwan1
- Avoids the use of up_aesinitialize() entirely, which resolves dependency problems, because this function does not make sure that an actual hardware aes implementation was made available: each SoC is now responsible to ensure the AES hardware is initialized before first use. This applies to lpc43xx, stm32 and sam34.
- Remove definitions of the NEVER used aes_init and aes_update operations. The new AES API will be more suitable.
- Change the unusual naming in stm32 (avoiding possible naming clashes)
- Change the unusual naming in sam34 (avoiding possible naming clashes)
- Add some FAR to pointers and enforce the 80 col limit in stm32 and sam
Fix lc823450 related
* configs/lc823450-xgevk: Fix IOB params in rndis/defconfig
These prameters work for HTTP audio streaming.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* arch/arm/src/lc823450: Fix up_allocate_heap() in lc823450_allocateheap2.c
This change fixes heap size and also implements up_addregion().
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: GregoryN <gnutt@nuttx.org>
arch/arm/src/stm32f0l0: Some fixes for a clean build. Still have a problem with lots of error messages coming from kconfig-mconf, but the configuation looks fine. Sometimes kconfig errors are difficult to spot. I would appreciate it anyone can spot the issue.
arch/arm/src/stm32f0l0/hardware: Rename the chip directory to hardware. This will hopefully eliminate some problems that I have seen with the chip include paths not being unique in more complex configuartions.
configs/nucleo-f072rb, configs/nucleo-f091rc, configs/stm32f051-discovery, and configs/stm32f072-discovery: Update for all of the naming changes made in arch/arm/src/stm32f0l0
arch/arm/include/stm32f0l0: Rename stm32f0 to stm32f0l0 to make a speace for STM32 L0. Rename files, functions and defines, removeing the f0_ from the names in order to make them MCU agnostic.
arch/arm/src/stm32f0l0: Rename stm32f0 to stm32f0l0 to make a speace for STM32 L0. Rename files, functions and defines, removeing the f0_ from the names in order to make them MCU agnostic.
arch/arm/src/tiva/hardware/cc13x0/cc13x0_fcfg1.h: Adjust cloned CC13x9 FCFG1 header file so that it reflects reality.
arch/arm/src/tiva/hardware/cc13x0/cc13x0_fcfg1.h: Add CC13x0 FCFG1 header file. Initial commit is the same as the CC13x2/CC26x2 FCFG1 header with a few name changes.
arch/arm/src/tiva/hardware/cc13x2_cc26x2/cc13x2_cc26x2_fcfg1.h: Initial FCFG1 header file for the cc13xx/cc26xx family.
arch/arm/src/tiva: Add GPIO IRQ stubs for clean compile
arch/arm/src/tiva/cc13xx: Add build framework for CC13xx GPIO interrupts. Change prototypes of some GPIO IRQ interfaces so that the function prototype is common between LM3S, LM4F, TM4C, and CC13xx.
Master
configs/nucleo-f334r8: add example for the SPWM generation (custom STM32 PWM usage)
arch/arm/src/stm32/stm32_pwm: fix compilation errors if the upper-half PWM logic is not enabled
include/nuttx/drivers/pwm.h: remove dependency on CONFIG_PWM for the upper-half PWM header. This allows compilation for the lower-level PWM drivers even if the upper-half PWM logic is not used.
arch/arm/src/stm32/stm32_tim.c: fix compilation error if there is no TIM8
configs/nucleo-f334r8/highpri: remove the upper-half ADC from configuration
configs/nucleo-f302r8/highpri: remove the upper-half ADC from configuration
configs/stm32f429i-disco/highpri: remove the upper-half ADC from configuration
Approved-by: GregoryN <gnutt@nuttx.org>
arch/arm/src/tiva: Add CC13xx GPIO driver plus various fixes for clean compilation.
arch/arm/src/tiva/ and configs/launchxl-cc1312r1: Make type of the GPIO pin configuration an abstract type so that CC13xx MCUs can share the same GPIO function prototypes and usage model.
arch/arm/src/tiva: Add CC13xx logic to enable power domains needed by peripherals and to enable clocking to peripherals.
arch/arm/src/tiva: Rename some header files so that they are unique in order to avoid including the wrong file. Fix various compile issues found during some initial trial builds.
arch/arm/src/tiva: Add CC13xx clock enable and power enable macros that are backward compatible with lm/tm4c macros.
Improvements in STM32 ADC
arch/arm/src/stm32/stm32_adc.c: start conversion on startup is now possible if TIM triggering selected. This can be useful to start ADC TIM conversion for ADC IPv2 when opening ADC device.
arch/arm/src/stm32/stm32_adc.c: fix compilation errors for chips with one ADV TIM
configs/nucleo-f303re: refresh ADC example
configs/nucleo-f334r8: refresh ADC example
Approved-by: GregoryN <gnutt@nuttx.org>
arch/arm/src/stm32h7/stm32_i2c.c
arch/arm/src/stm32l4/stm32l4_i2c.c
Those easy because F7 patch applied with no problem (after changing path and file names appropriately). The patch could not be appleed to the following. The logic is different. I don't know if a similar change is needed there or not.
arch/arm/src/stm32/stm32f30xxx_i2c.c
arch/arm/src/stm32/stm32f40xxx_i2c.c
arch/arm/src/stm32/stm32_i2c.c
arch/arm/src/stm32/stm32_i2c_alt.c
arch/arm/src/stm32f0/stm32f0_i2c.c
stm32f7:i2c out of bounds access on priv->msgv
Error in if statment. It was checking for msgc > 0.
If message count is 1, only index 0 is valid on
priv->msgv. There for random values in memory were
used to set next_norestart.
Approved-by: GregoryN <gnutt@nuttx.org>
arch/arm/include/stm32/chip.h: remove redundant STM32 family definitions. It is already done in arch/arm/src/stm32/Kconfig
Approved-by: GregoryN <gnutt@nuttx.org>
arch/arm/src/stm32/stm32_adc.c: refactor adc_reset. It should be easier to maintain this code if it's divided into smaller functions
Approved-by: GregoryN <gnutt@nuttx.org>
Use STM32 DMA IP core version instead of chip family names and some minor improvements
arch/arm/src/stm32/chip/stm32_adc.h: raise error if two IP cores seleceted
libs/libdsp/Kconfig: cosmetic change
arch/arm/src/stm32/Kconfig: hide TIMER menu, HRTIM menu and USB Host debug menu if peripherals not enabled
configs/stm32f429i-disco/highpri/defconfig: fix configuration warning
Approved-by: GregoryN <gnutt@nuttx.org>
configs/nucleo-f207zg, configs/nucleo-f103rb: add ADC and PWM examples; arch/arm/src/stm32_adc.c: there is no DMA CFG bit for the basic IPv1 ADC
Approved-by: GregoryN <gnutt@nuttx.org>
arch/arm/src/tiva/hardwar: Move LM3S and LM4F include files to hardware/lm/ sub-directory. Move all TM4C header files files to hardware/tm4c/ sub-directory.
arch/arm: Add basic configuration/build support for CC13xx parts. Conditioned on EXPERIMENTAL.
Squashed commit of the following:
arch/arm/src/tiva/Make.defs: Trivial change to conditional VPATH.
arch/arm/src/tiva: Move LM3S and LM4F source files to lm/ sub-directory. Move all TM4C source files to tm4c sub-directory.
arch/arm/src/tiva and configs/: Change include patch from chip/ to hardware/ in all Tiva files includes.
arch/tmp/src: Rename chip/ subdirectory to hardware/. This is a better name since it does not conflict with other directory names and, well, we are going to be change a lot of the Tiva directory structure in the next few commits.
arch/arm/src/max326xx/max32660/max32660_spim.c: SPI0 master mode support is complete (sans DMA and completely untested). configs/max32660-evsys/src: Add framework for SPI support.
arch/arm/src/max326xx/max32660/max32660_spim.c: Fleshes out some of the data transfer logic. More needs to be done. Also removes leveraged DMA support. It will be a long time (if ever) before DMA is supported. No point in dragging all of that bogus logic around.
Squashed commit of the following:
arch/arm/src/max326xx/max32660/max32660_spim.c: A few updates tot he SPI master driver. Still incomplete and does not even compile.
Update some comments
arch/arm/src/max326xx: Clean up some general build issues. Still STM32 code posing as MAX32660.
arch/arm/src/max326xx: Starting SPI driver. Initial commit is just the STM32 SPI driver with name changes.
arch/arm/src/max326xx and configs/max32660-evsys/src: Fix some issues with GPIO setup of output pins. Correct polarity of on-board LED output. The on-board LED is now functional.
arch/arm/src/max326xx: WFI instruction in IDLE loop seems to interfere with stability. Commented out for now. Needs to be investigated further.
arch/arm/src/max326xx: Fixes for GPIO configuration problems and serial driver problems. I now get the NuttShell prompt (if I also band on ENTER to force all of the characters out). Progress, but not yet ready.
configs/max32660-evsys: Support CONFIG_BOOT_RUNFROMISRAM=y.
