libs/libc/misc/Make.defs: For platforms whose CPP tool does not support a variable number arguments to pre-processor macros, we may still need to build the debug functions even when CONFIG_DEBUG_FEATURES is not selected. For example, __alert() may be needed is CONFIG_ARCH_STACKDUMP is set.
configs/makerlisp: Add an sdboot configuration that will load .hex files from the SD card.
Squashed commit of the following:
configs/makerlisp/scripts/makerlisp_ram.linkcmd: Fixup .RESET and .STARTUP. These need to be redirected to RAM since they default to ROM.
configs/makerlisp/scripts/makerlisp_ram.linkcmd: Restore some settings that should be unnecessary but are really required by the current implementation.
configs/makerlisp: Rename nsh configuratinon to nsh_flash. Create new configuration, nsh_ram, that is identical to the nsh_flash configuration except that the code runs out of external SRAM.
configs/makerlisp/scripts: Add a linker script to support execution from RAM.
configs: spresense: add USBDEV_SETNOTIFYSIG signal id
Set signal id for notify USB device connection status and
supply current value.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
configs: spresense: Enable UID functionality
To enable the UID functionality for spresense board
set BOARDCTL_UNIQUEID in menuconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
configs/lc823450-xgevk: Remove cpu assignment for lpwork
This change will reduce audio underrun when running dvfs auto mode.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
configs: spresense: add I2CTOOL support and extend GPIO for future use
* arch: arm: cxd56xx: add delay support
add delay support for cxd56xx chip
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: register I2C busses
for development is usefull to register I2C busses when the I2CTOOL
is built
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs:spresense: enable GPIO interface
enable GPIO interface on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
NOTE: There's one change that might be incorrect, where I skip interfaces with zero endpoints. I did this because my device has two consecutive interface descriptors with the same interface number, one for altsetting 0 with no endpoints, and another for altsetting 1 with 1 endpoint. The loop was aborting due to finding two interface descriptors back-to-back.
configs: spresense: enable BMI160_I2C sensor
* drivers: sensors: add BMI160 driver
Enable driver support for the Bosch BMI160 Inertial
Measurement sensor
This driver can be used with the BMI160 sensor connected over
SPI or I2C bus
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: enable BMI160_I2C sensor
Enable BMI160 sensor connected over I2C on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
configs: spresense: remove SPI MMC/SD & add ADC
* configs: spresense: remove SPI MMC/SD support
SPI MMC/SD is not used on spresense board.
A commit will follow to add support for custom boards
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: enable ADC support
enable ADC support for spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arch: arm: cxd56xx: SCU, ADC, I2C
* nuttx: configs: spresense: LEDS: fix warnings
In the initial code several errors were missed because I pushed
the dirty code.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add Sensor Control Unit (SCU)
Add Sensor Control Unit (SCU) on cxd56xx chip
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add I2C support
add I2C support on cxd56xx chip
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add ADC interface support
Add ADC interface support on cxd56xx chip
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: Use DMAC for reading sensing data
Use DMAC for reading sensing data from SCU on cxd56xx chip
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: code style sanitization
NuttX does not use Deoxygen for documentation and no file should contain Doxygen tags or Doxygen style comments.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: enable I2CDEV
add enable I2CDEV for spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: add notification LEDs
Add usefull diagnostic LEDs on the speresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arch: arm: cxd56xx: add UID support
* arch: arm: cxd56xx: add UID support
Add support to be able to read the HW UID
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: enable USERLEDS
add USERLED for spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
