This patch fixes the issue that k230_hart_is_big() doesn't work in
S-mode. It also adds convenient debug macros to ease debugging process
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
Some stm32 has alternate USART6 pinout on G9/G14 but others have it
on A12/A11. Unfortunately it's very difficult to make proper ifdefs for
this since position is based on package (and pincount) and not chip
itself. Creating such list would take a lot of time. Because of that
I just added another possible config for this pin and moved responsibility
of proper selection onto board code.
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
Onewire driver wants to use "struct up_dev_s *priv", which is extracted
from "struct uart_dev_s" and "struct inode". But inode and uart dev are
only declared when TERMIOS or BSDCOMPAT is also enabled. Without these
driver fails to compile with missing declaration errors. Adding some
additional "#if defined()" to these declarations fix the issue and driver
compiles and works properly (tested with ds18b20 temp sensor).
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
This driver is used with QEMU, to make it possible
to use networking.
This is not the MAC in ESP32, however, it can be used with QEMU.
The code was shamelessly copied from 31dac92e5f
This patch simplifies PMP handling for K230 using common APIs.
It also uses `g_misa` variable to expose the MISA issue.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
check if interrupt is busy when IRQCHAIN is disabled
this allows user to catch configuration errors and fail early when the
already busy vector is reused
Signed-off-by: p-szafonimateusz <p-szafonimateusz@xiaomi.com>
at default x86_64 supports SSE, SSE2, this commit adds support for
SSE3, SSSE3, SSE41, SSE42 and SSE4A
Signed-off-by: p-szafonimateusz <p-szafonimateusz@xiaomi.com>
this partly revert 4123615621 which works OK for PCI serial and network cards
but breaks QEMU EDU due to usage of sem and usleep in IDLE thread context.
Another solution will be provided later.
Signed-off-by: p-szafonimateusz <p-szafonimateusz@xiaomi.com>
Current NuttX SBI assumes empty PMP settings but that is not always
true, for example some bootloaders may have PMP entries locked before
handling over to NuttX. This patch revises it by not using hardcoded
PMP region number.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
Reproduce:
configure:
./tools/configure.sh qemu-armv7a:nsh -j8
open kasan:
CONFIG_MM_KASAN=y
run:
qemu-system-arm -cpu cortex-a7 -nographic -machine virt,virtualization=off,gic-version=2 -net none -chardev stdio,id=con,mux=on -serial chardev:con -mon chardev=con,mode=readline -kernel ./nuttx
error:
run hanged
Rootcause:
In Qemu armv7a, the ram-end reserved for MMU PGTABLE:
And the up_allocate_heap() directly use the ram-end for heap in arch/arm/src/common/arm_allocateheap.c
*heap_size = CONFIG_RAM_END - g_idle_topstack;
Then they are conflict.
Usually, we won't use the heap end, so can't find the error.
BUT, the KASAN will use the heap end for shadow, so found the error.
Resolve:
up_allocate_heap() consider of MMU, re-define the RAM_END at chip.h
Signed-off-by: ligd <liguiding1@xiaomi.com>
This commit adds support for TX DMA transfers for USART peripheral. Code
refactor in sam_serial.h was also required in order to have correct
defines for all possible cases (both RX and TX DMA used, just one used,
none used).
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
When an application is being loaded `up_addrenv_create ` calls
`create_region` to create the address environment. Only the first
entry is mapped when the region is created. Virtual memory that is
not mapped will trigger an exception when accessed. Other memory
pages are allocated and mapped on-demand. This enables setting
larger heap and stack for the process without compromising the
overall system memory.
Current `CONFIG_PAGING` refers to an experimental implementation
to enable embedded MCUs with some limited RAM space to execute
large programs from some non-random access media.
On-demand paging should be implemented for the kernel mode with
address environment implementation enabled.
Previously we need turn off the PMP locks in K230 vendor u-boot to use
NuttX, this complicates the setup process. This patch supports running
NuttX with original vendor u-boot so that to reduce setup complexity.
It also enables empty NSH prompt string in AMP master config as the apps
side support is ready.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
